Volvo EX90 Charging at EnergyVision

Volvo EX90 Plugged In but the Charger Will Not Start

You connected the cable to your Volvo EX90 and nothing happens. No charging indicator on the screen, no confirmation from the charger. The EX90 supports Plug & Charge and multiple authentication methods, but when none of them work, you need to troubleshoot step by step.

Symptoms

• Charger displays an error after plugging in the EX90
• Charge port LED does not light up or stays amber
• 14.5-inch center screen shows no active charging session
• Charger screen says 'waiting for vehicle' or shows a timeout
• CCS connector plugs in but does not lock into the charge port

What to Do

1. 1

   Authenticate with the charger

   Check the charger's screen for payment instructions. Tap your RFID card, open the charging network's app, or use contactless payment. Plug & Charge should activate automatically on supported networks, but if it does not, use manual authentication.

2. 2

   Check the charge port on the left rear

   Open the charge port door fully. Check for ice, snow, or debris. In winter, gently clear any obstructions. Make sure the port cover is not partially blocking the connector.

3. 3

   Seat the connector firmly

   Push the CCS2 connector straight into the port until it clicks and locks. If it will not lock, pull it out and try again. Check that the connector pins are clean and undamaged.

4. 4

   Turn off scheduled charging

   On the center screen, go to Settings, then Charging. If a charging schedule is active, disable it or switch to 'charge immediately.' This is a common reason charging will not start at public chargers.

5. 5

   Restart the charging process

   Unplug the connector, lock and unlock the car using the Volvo Cars app or key, wait 15 seconds, then plug in again. This resets the charging communication.

Volvo EX90 Charger Payment Failed or Card Declined

You are at a public charger with your Volvo EX90 and the payment will not go through. The card reader rejects your card, the app throws an error, or Plug & Charge just does not activate. Payment issues at public chargers are one of the most common frustrations, and they have nothing to do with your car's charging system.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Plug & Charge does not activate when you connect the cable
• Charging app shows a payment error or insufficient balance
• Contactless payment terminal does not respond
• You cannot find any way to pay at the charger

What to Do

1. 1

   Check Plug & Charge status in the Volvo Cars app

   Open the Volvo Cars app and verify that Plug & Charge is enabled with a valid payment method. If the network supports it, try unplugging and reconnecting. If not, proceed to manual payment.

2. 2

   Try a different payment method

   Use a different credit or debit card, your phone's mobile wallet, or the charging network's app. Having multiple options avoids being stuck when one fails.

3. 3

   Check for pre-authorization holds

   Open your banking app and look for pending charges from the charging network. Multiple failed attempts may have placed several holds, reducing your available balance. Contact your bank if needed.

4. 4

   Use the charging network's app instead

   Find the network name on the charger. Download their app, create an account, add a payment method, and start the session through the app. This bypasses the physical payment terminal entirely.

5. 5

   Tap your RFID charging card

   If you carry an RFID card from a charging provider or roaming service, tap it on the charger's card reader. RFID cards are often more reliable than apps or contactless terminals.

Volvo EX90 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX90 expecting 250 kW and the 14.5-inch screen shows 60 kW. Or your wallbox is only delivering 3 kW instead of 11 kW. The EX90 has one of the fastest charging speeds in its class, but reaching that peak depends on battery temperature, state of charge, and the charger itself.

Symptoms

• DC fast charging speed well below the 250 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 40-50%
• Center screen shows lower power than the charger's rated output
• Charging session starts strong but slows down within 10 minutes

What to Do

1. 1

   Set the charger as your navigation destination

   Use Google Maps on the 14.5-inch center screen to navigate to the charging station. The EX90 will start preconditioning the battery automatically during the drive, preparing it for peak charging speed.

2. 2

   Check the charger's rated power

   Before plugging in, check the charger's label or the app for its maximum output. If the charger is rated at 150 kW, your EX90 cannot charge faster than 150 kW regardless of its 250 kW capability.

3. 3

   Check your state of charge

   For the fastest charging, arrive between 10-20%. The EX90's peak speeds are available at lower states of charge. Above 80%, charging will slow significantly.

4. 4

   Verify the charger is not sharing power

   Many chargers split power between two connectors. If someone is using the adjacent stall, both cars get reduced speeds. Move to a charger with both stalls free.

5. 5

   Check AC charge current settings

   If charging slowly on AC, check the EX90's settings to ensure the charge current limiter is set to maximum. Also verify your wallbox is properly wired for 3-phase.

6. 6

   Try a higher-powered charger

   To take advantage of the EX90's 250 kW capability, look for chargers rated at 300 kW or higher. These are available from networks like Ionity, Fastned, and others.

Session won't start or authentication fails

You try to start a session through the EnergyVision app or charge card, but the charger does not respond or shows an error.

Symptoms

• The app will not connect to the charger or keeps loading
• Your RFID charge card is not recognized
• You have no mobile data at the station location
• The charger screen shows an error after authentication

How to Fix It

1. 1

   Install and set up the EnergyVision app before you travel

   Create your account and add a payment method at home, on a reliable internet connection. Do not try to set up the app for the first time at a station with weak signal.

2. 2

   Try a different authentication method

   If the app is not working, try your EnergyVision charge card (RFID) instead, or vice versa. Having both options available increases your chances of starting a session.

3. 3

   Try switching between Wi-Fi and mobile data

   Some apps struggle with certain network configurations. Toggle your phone's Wi-Fi off (or on, if a nearby network is available) and try again. Sometimes a network switch forces the app to reconnect.

4. 4

   Restart the app and your phone

   Close the app completely (not just minimize), reopen it, and try again. If that fails, restart your phone.

5. 5

   Have a backup charging app ready

   Always carry a second charging app from a larger network. If EnergyVision is not working, you need to find an alternative charger from another operator.

Limited station coverage

EnergyVision has fewer stations than major networks. This means longer distances between chargers and fewer alternatives if a station is broken or occupied.

Symptoms

• The app shows very few stations along your route
• The nearest EnergyVision station is 50 km or more away
• You arrived at the only EnergyVision station in the area and it is out of order
• There is no second EnergyVision charger to fall back to

How to Fix It

1. 1

   Never rely on EnergyVision as your only charging option

   Plan your route with at least one alternative network at each stop. EnergyVision stations are a bonus when they work, but their spacing means you cannot depend on them exclusively.

2. 2

   Install apps for larger networks in the same region

   Identify which major networks operate near EnergyVision stations (Ionity, Shell Recharge, Fastned, or regional operators). Install their apps so you can switch quickly if needed.

3. 3

   Use a multi-network route planner

   A Better Routeplanner (ABRP) or similar tools show chargers from all operators. Plan your stops based on all available chargers, not just one network. EnergyVision stations will appear where they exist.

4. 4

   Charge a little extra at reliable stations before entering sparse areas

   If your next stop is an EnergyVision station in an area with few alternatives, charge to 90% at the station before it instead of the usual 80%. The extra buffer gives you range to reach a different charger if the EnergyVision station is down.

Different charger hardware at different locations

EnergyVision uses charger units from different manufacturers at different stations. This means the physical interface, cable handling, and screen layout vary from one station to the next.

Symptoms

• The charger at this station looks completely different from the last EnergyVision station you used
• The connector release mechanism works differently than expected
• The charger screen layout does not match what you see in the app
• Error codes or messages are in a different format than at other EnergyVision stations

How to Fix It

1. 1

   Check the charger unit for basic instructions

   Most charger manufacturers print basic instructions on the unit itself: where to plug in, how to release the connector, and where the emergency stop button is. Take a moment to read these, as they vary between manufacturers.

2. 2

   Start the session through the app, not the charger screen

   Regardless of the charger hardware, the EnergyVision app is the consistent interface. Start and stop sessions through the app. The charger screen is secondary.

3. 3

   If the connector release is different, check for a button or lever

   Some charger manufacturers use a push-button release, others use a lever, and some release automatically when the session ends. Look at the connector handle and the charger unit for release instructions.

4. 4

   Report hardware-specific problems in the app

   If a charger unit from a specific manufacturer is repeatedly problematic, report it through the EnergyVision app. Include details about what happened so the support team can pass it to the hardware vendor.

App not available in all app stores or regions

Smaller networks sometimes have app availability issues. The EnergyVision app may not appear in your app store if your account is set to a country where EnergyVision does not operate.

Symptoms

• You search for 'EnergyVision' in your app store and no results appear
• The app is listed but marked as 'not available in your country'
• You found the app but it will not install on your phone model
• A link to the app store listing leads to a 'not found' page

How to Fix It

1. 1

   Check the EnergyVision website for the correct app name and link

   The app may be listed under a slightly different name in some app stores. Visit the EnergyVision website on your phone and look for a direct download link that opens the correct store listing.

2. 2

   Check your app store country setting

   If your App Store or Google Play account is set to a country where EnergyVision does not operate, the app may be hidden. You can check this in your store account settings.

3. 3

   Check if a roaming app supports EnergyVision stations

   Some roaming platforms include smaller networks. Search for the station location in a roaming app (like Chargemap or Octopus Electroverse) to see if you can start a session through a third-party app instead.

4. 4

   Contact EnergyVision support for alternative access

   If you cannot install the app, contact EnergyVision through their website. They may have a web-based session starter or be able to suggest a roaming provider that includes their stations.

Slower support response times

As a smaller operator, EnergyVision may have fewer support staff than major networks. Response times for non-urgent issues can be longer, and phone support may have limited hours.

Symptoms

• You reported an issue through the app and have not heard back
• The support phone number goes to voicemail or has limited hours
• You need help at a station but cannot reach anyone
• Your email to support has not been answered after several days

How to Fix It

1. 1

   Use the app's support feature for the fastest response

   In-app support requests typically get prioritized over emails sent to a general address. If the app has a help, chat, or report issue option, use that first.

2. 2

   Include all relevant details in your first message

   To avoid back-and-forth that stretches across days, include: station location, charger ID (printed on the unit), time of the issue, what happened, and any error messages. Screenshots help.

3. 3

   Do not wait at a broken charger for support to respond

   If a charger is not working and support is not answering, move on. Report the issue through the app and drive to the next available charger from any network. Waiting at a broken charger hoping for a callback is not practical.

4. 4

   For billing disputes, document everything

   Screenshot your charging session details (from the app), note the charger ID and time, and save any error messages. If you were charged for a failed session, this documentation helps you get a refund when support responds.