Volvo EX90 Charging at Recharge

Volvo EX90 Plugged In but the Charger Will Not Start

You connected the cable to your Volvo EX90 and nothing happens. No charging indicator on the screen, no confirmation from the charger. The EX90 supports Plug & Charge and multiple authentication methods, but when none of them work, you need to troubleshoot step by step.

Symptoms

• Charger displays an error after plugging in the EX90
• Charge port LED does not light up or stays amber
• 14.5-inch center screen shows no active charging session
• Charger screen says 'waiting for vehicle' or shows a timeout
• CCS connector plugs in but does not lock into the charge port

What to Do

1. 1

   Authenticate with the charger

   Check the charger's screen for payment instructions. Tap your RFID card, open the charging network's app, or use contactless payment. Plug & Charge should activate automatically on supported networks, but if it does not, use manual authentication.

2. 2

   Check the charge port on the left rear

   Open the charge port door fully. Check for ice, snow, or debris. In winter, gently clear any obstructions. Make sure the port cover is not partially blocking the connector.

3. 3

   Seat the connector firmly

   Push the CCS2 connector straight into the port until it clicks and locks. If it will not lock, pull it out and try again. Check that the connector pins are clean and undamaged.

4. 4

   Turn off scheduled charging

   On the center screen, go to Settings, then Charging. If a charging schedule is active, disable it or switch to 'charge immediately.' This is a common reason charging will not start at public chargers.

5. 5

   Restart the charging process

   Unplug the connector, lock and unlock the car using the Volvo Cars app or key, wait 15 seconds, then plug in again. This resets the charging communication.

Volvo EX90 Charger Payment Failed or Card Declined

You are at a public charger with your Volvo EX90 and the payment will not go through. The card reader rejects your card, the app throws an error, or Plug & Charge just does not activate. Payment issues at public chargers are one of the most common frustrations, and they have nothing to do with your car's charging system.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Plug & Charge does not activate when you connect the cable
• Charging app shows a payment error or insufficient balance
• Contactless payment terminal does not respond
• You cannot find any way to pay at the charger

What to Do

1. 1

   Check Plug & Charge status in the Volvo Cars app

   Open the Volvo Cars app and verify that Plug & Charge is enabled with a valid payment method. If the network supports it, try unplugging and reconnecting. If not, proceed to manual payment.

2. 2

   Try a different payment method

   Use a different credit or debit card, your phone's mobile wallet, or the charging network's app. Having multiple options avoids being stuck when one fails.

3. 3

   Check for pre-authorization holds

   Open your banking app and look for pending charges from the charging network. Multiple failed attempts may have placed several holds, reducing your available balance. Contact your bank if needed.

4. 4

   Use the charging network's app instead

   Find the network name on the charger. Download their app, create an account, add a payment method, and start the session through the app. This bypasses the physical payment terminal entirely.

5. 5

   Tap your RFID charging card

   If you carry an RFID card from a charging provider or roaming service, tap it on the charger's card reader. RFID cards are often more reliable than apps or contactless terminals.

Volvo EX90 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX90 expecting 250 kW and the 14.5-inch screen shows 60 kW. Or your wallbox is only delivering 3 kW instead of 11 kW. The EX90 has one of the fastest charging speeds in its class, but reaching that peak depends on battery temperature, state of charge, and the charger itself.

Symptoms

• DC fast charging speed well below the 250 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 40-50%
• Center screen shows lower power than the charger's rated output
• Charging session starts strong but slows down within 10 minutes

What to Do

1. 1

   Set the charger as your navigation destination

   Use Google Maps on the 14.5-inch center screen to navigate to the charging station. The EX90 will start preconditioning the battery automatically during the drive, preparing it for peak charging speed.

2. 2

   Check the charger's rated power

   Before plugging in, check the charger's label or the app for its maximum output. If the charger is rated at 150 kW, your EX90 cannot charge faster than 150 kW regardless of its 250 kW capability.

3. 3

   Check your state of charge

   For the fastest charging, arrive between 10-20%. The EX90's peak speeds are available at lower states of charge. Above 80%, charging will slow significantly.

4. 4

   Verify the charger is not sharing power

   Many chargers split power between two connectors. If someone is using the adjacent stall, both cars get reduced speeds. Move to a charger with both stalls free.

5. 5

   Check AC charge current settings

   If charging slowly on AC, check the EX90's settings to ensure the charge current limiter is set to maximum. Also verify your wallbox is properly wired for 3-phase.

6. 6

   Try a higher-powered charger

   To take advantage of the EX90's 250 kW capability, look for chargers rated at 300 kW or higher. These are available from networks like Ionity, Fastned, and others.

Charger stuck in "preparing" state

You authenticated successfully, the charger says "preparing," but it never starts delivering power. This is one of the most reported issues on Recharge stations, especially at older units.

Symptoms

• Charger screen shows "Preparing" or "Initializing" for more than two minutes
• Your car's charging indicator does not activate
• The Recharge app shows the session as active but 0 kW delivered
• The charger fan spins up but no power flows

How to Fix It

1. 1

   Wait up to three minutes

   Some Recharge units, particularly the 300kW stations, take longer to complete the power handshake with your car. Give it a full three minutes before taking action.

2. 2

   Unplug and reconnect

   Remove the CCS2 connector, wait 15 seconds, then plug it back in firmly. This resets the communication between your car and the charger.

3. 3

   Stop the session in the Recharge app and start a new one

   Open the Recharge app, tap Stop on the active session, wait for it to fully end, then start a new session on the same charger. This clears any stuck state on the backend.

4. 4

   Try the other connector on the same unit

   Many Recharge stations have two CCS2 connectors. If one is stuck, the other connector on the same unit often works fine.

5. 5

   Use a different authentication method

   If you started with the app, try your RFID card instead, or vice versa. Sometimes the issue is with the authentication path, not the charger hardware.

Old Fortum branding causes app scan failure

Recharge was originally part of Fortum's charging operations before being spun off as a separate company. Some older stations still display Fortum logos and QR codes. Scanning an old Fortum QR code with the Recharge app may not work, or it may redirect to a dead Fortum page.

Symptoms

• QR code on the charger opens a Fortum website or shows an error
• Recharge app says "Charger not found" after scanning
• Station ID on the physical unit does not match what the Recharge app expects
• The charger has Fortum branding but is listed as Recharge in third-party apps

How to Fix It

1. 1

   Ignore the QR code and search by station name in the Recharge app

   Open the Recharge app, use the map or search to find the station by location. The charger will appear under its Recharge name even if the physical unit still says Fortum.

2. 2

   Enter the charger ID manually

   Look for a numeric ID on the charger, often printed on a sticker near the connector. In the Recharge app, tap "Enter ID" and type it in directly.

3. 3

   Use RFID or contactless payment instead of the app

   Tap your Recharge RFID card or a contactless bank card on the reader. This bypasses the app entirely and works regardless of the branding on the charger.

4. 4

   Check if contactless is available on this unit

   Not all Recharge stations support contactless bank card payment. Look for a card reader terminal on the charger. If there is no terminal, you will need the app or an RFID card.

RFID card from old Fortum account not recognized

If you had a Fortum Charge & Drive account and RFID card, it may not work automatically on the Recharge network. Some cards were migrated, others were not.

Symptoms

• Tapping your old Fortum RFID card shows "Card not recognized" on the charger
• The charger beeps but does not start a session
• Your Fortum card works on some stations but not others

How to Fix It

1. 1

   Log in to the Recharge app and check your RFID cards

   Open the Recharge app, go to your account settings, and look under RFID cards. If your old Fortum card is not listed, it was not migrated automatically.

2. 2

   Re-register your RFID card

   In the Recharge app, tap "Add RFID card" and follow the steps. You will need the card number printed on the back of your RFID card.

3. 3

   Use the app to start the session while you wait for RFID activation

   RFID card registration can take up to 24 hours to propagate across all stations. Use the app to authenticate in the meantime.

4. 4

   Order a new Recharge RFID card if re-registration fails

   Some older Fortum cards use a chip format that is not compatible. You can order a new Recharge RFID card through the app or website.

Contactless payment not accepted

You are trying to tap your bank card or phone to pay, but the charger does not respond or shows an error. Contactless payment availability varies across Recharge stations.

Symptoms

• No card reader terminal visible on the charger
• Card reader shows "Payment failed" or does not respond to taps
• Apple Pay or Google Pay not recognized
• The charger prompts for an RFID card but you only have a bank card

How to Fix It

1. 1

   Check if this station supports contactless payment

   Look for a separate payment terminal with a contactless symbol. Not all Recharge stations have been upgraded. The Recharge app shows payment options for each station on the station detail page.

2. 2

   Try removing and re-holding your card

   Hold your card flat against the reader for at least three seconds. Some terminals need a longer hold than you might expect. Remove the card fully, then try again.

3. 3

   Fall back to the Recharge app

   If contactless is not working, open the Recharge app and start the session from there. You need a payment method saved in the app.

4. 4

   Try a different card

   Some Visa Electron and certain prepaid cards are not accepted by the payment terminals. A standard Visa or Mastercard debit or credit card usually works.

Charging speed much lower than expected

The station is rated for 300kW, but your car is only pulling 50kW or less. While your car's battery management limits the maximum speed, Recharge stations can also throttle power.

Symptoms

• Charger display shows far less power than the station's rated capacity
• Charging speed drops suddenly mid-session
• Other cars at the same station are also charging slowly
• The Recharge app shows the session but at low power

How to Fix It

1. 1

   Check how many other cars are charging at the same station

   Recharge stations with multiple connectors often share a power cabinet. If two or three cars are charging simultaneously, the available power per car drops. This is normal and not a fault.

2. 2

   Check your battery level

   DC fast charging slows significantly above 80% on most EVs. If your battery is above 70-80%, the slower speed is your car protecting the battery, not a problem with the Recharge station.

3. 3

   Check the temperature

   In cold weather, your car may limit charging speed until the battery warms up. This can take 10-15 minutes of charging before speeds increase. Some cars precondition the battery if you set the charger as a destination in navigation.

4. 4

   Try a different connector at the station

   Individual connectors can have faults that limit power output. If another connector is free, unplug and try it.

5. 5

   Report the issue in the Recharge app

   If the speed is unusually low and none of the above apply, report it through the Recharge app. Tap the active session and look for a "Report issue" option. This helps Recharge identify hardware problems.