Volvo EX90 Charging at Atlante

Volvo EX90 Plugged In but the Charger Will Not Start

You connected the cable to your Volvo EX90 and nothing happens. No charging indicator on the screen, no confirmation from the charger. The EX90 supports Plug & Charge and multiple authentication methods, but when none of them work, you need to troubleshoot step by step.

Symptoms

• Charger displays an error after plugging in the EX90
• Charge port LED does not light up or stays amber
• 14.5-inch center screen shows no active charging session
• Charger screen says 'waiting for vehicle' or shows a timeout
• CCS connector plugs in but does not lock into the charge port

What to Do

1. 1

   Authenticate with the charger

   Check the charger's screen for payment instructions. Tap your RFID card, open the charging network's app, or use contactless payment. Plug & Charge should activate automatically on supported networks, but if it does not, use manual authentication.

2. 2

   Check the charge port on the left rear

   Open the charge port door fully. Check for ice, snow, or debris. In winter, gently clear any obstructions. Make sure the port cover is not partially blocking the connector.

3. 3

   Seat the connector firmly

   Push the CCS2 connector straight into the port until it clicks and locks. If it will not lock, pull it out and try again. Check that the connector pins are clean and undamaged.

4. 4

   Turn off scheduled charging

   On the center screen, go to Settings, then Charging. If a charging schedule is active, disable it or switch to 'charge immediately.' This is a common reason charging will not start at public chargers.

5. 5

   Restart the charging process

   Unplug the connector, lock and unlock the car using the Volvo Cars app or key, wait 15 seconds, then plug in again. This resets the charging communication.

Volvo EX90 Charger Payment Failed or Card Declined

You are at a public charger with your Volvo EX90 and the payment will not go through. The card reader rejects your card, the app throws an error, or Plug & Charge just does not activate. Payment issues at public chargers are one of the most common frustrations, and they have nothing to do with your car's charging system.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Plug & Charge does not activate when you connect the cable
• Charging app shows a payment error or insufficient balance
• Contactless payment terminal does not respond
• You cannot find any way to pay at the charger

What to Do

1. 1

   Check Plug & Charge status in the Volvo Cars app

   Open the Volvo Cars app and verify that Plug & Charge is enabled with a valid payment method. If the network supports it, try unplugging and reconnecting. If not, proceed to manual payment.

2. 2

   Try a different payment method

   Use a different credit or debit card, your phone's mobile wallet, or the charging network's app. Having multiple options avoids being stuck when one fails.

3. 3

   Check for pre-authorization holds

   Open your banking app and look for pending charges from the charging network. Multiple failed attempts may have placed several holds, reducing your available balance. Contact your bank if needed.

4. 4

   Use the charging network's app instead

   Find the network name on the charger. Download their app, create an account, add a payment method, and start the session through the app. This bypasses the physical payment terminal entirely.

5. 5

   Tap your RFID charging card

   If you carry an RFID card from a charging provider or roaming service, tap it on the charger's card reader. RFID cards are often more reliable than apps or contactless terminals.

Volvo EX90 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX90 expecting 250 kW and the 14.5-inch screen shows 60 kW. Or your wallbox is only delivering 3 kW instead of 11 kW. The EX90 has one of the fastest charging speeds in its class, but reaching that peak depends on battery temperature, state of charge, and the charger itself.

Symptoms

• DC fast charging speed well below the 250 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 40-50%
• Center screen shows lower power than the charger's rated output
• Charging session starts strong but slows down within 10 minutes

What to Do

1. 1

   Set the charger as your navigation destination

   Use Google Maps on the 14.5-inch center screen to navigate to the charging station. The EX90 will start preconditioning the battery automatically during the drive, preparing it for peak charging speed.

2. 2

   Check the charger's rated power

   Before plugging in, check the charger's label or the app for its maximum output. If the charger is rated at 150 kW, your EX90 cannot charge faster than 150 kW regardless of its 250 kW capability.

3. 3

   Check your state of charge

   For the fastest charging, arrive between 10-20%. The EX90's peak speeds are available at lower states of charge. Above 80%, charging will slow significantly.

4. 4

   Verify the charger is not sharing power

   Many chargers split power between two connectors. If someone is using the adjacent stall, both cars get reduced speeds. Move to a charger with both stalls free.

5. 5

   Check AC charge current settings

   If charging slowly on AC, check the EX90's settings to ensure the charge current limiter is set to maximum. Also verify your wallbox is properly wired for 3-phase.

6. 6

   Try a higher-powered charger

   To take advantage of the EX90's 250 kW capability, look for chargers rated at 300 kW or higher. These are available from networks like Ionity, Fastned, and others.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.