Polestar 2 Charging at Shell Recharge

Polestar 2 Charger Won't Start or Begin Charging

You have plugged in your Polestar 2, the connector clicked, but nothing happens. The center display stays silent or shows an error. This is frustrating, but it is almost always fixable on the spot without calling support.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the center display
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• Polestar 2 charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Center display briefly shows charging screen, then returns to idle

What to Do

1. 1

   Unplug and reconnect firmly

   Remove the CCS2 or Type 2 connector, wait 10 seconds, then reinsert it with a firm push until you hear a clear click. Watch the charge port LED on the Polestar 2 for a steady light.

2. 2

   Check for a charging schedule

   On the center display, go to Settings, then Charging. If a charging schedule is active, disable it or set it to 'Direct' so the car charges immediately when plugged in.

3. 3

   Restart the charger session

   On the charger, end the current session if one is shown. Then start a new session by tapping your RFID card or restarting in the charger's app. Some chargers have a physical start/stop button.

4. 4

   Try Plug & Charge or a different payment method

   If your Polestar 2 has Plug & Charge enabled, check the charger supports it. Otherwise, switch to a different RFID card, contactless payment, or the charger operator's app.

5. 5

   Reboot the car's infotainment system

   Press and hold the home button on the center display for about 15 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication module.

6. 6

   Try a different charger or cable

   If the station has multiple stalls, move to a different one. If you are using a tethered cable, try bringing your own Type 2 cable. A faulty charger cable is more common than a faulty car.

Polestar 2 Charging Payment Failed at the Station

You are at the charger, your Polestar 2 is ready, but the payment will not go through. The charger says 'Authorization failed' or just does nothing after you tap your card. Payment issues are one of the most common reasons a charging session never starts, and they are usually fixable in a couple of minutes.

Symptoms

• Charger screen shows 'Authorization failed' or 'Payment declined' after tapping your card or RFID
• Charger app shows an error when trying to start a remote session for your Polestar 2
• Contactless bank card is declined even though it works at shops
• Plug & Charge does not activate automatically after plugging in the CCS2 connector
• Charger accepts payment but the session immediately ends with a zero-kWh charge

What to Do

1. 1

   Check if Plug & Charge is enabled

   On the Polestar 2 center display, go to Settings, then Charging. Confirm Plug & Charge is turned on. If it is on but the charger did not start automatically, this station likely does not support it. Use a different payment method.

2. 2

   Try the charger operator's app

   Look for the operator name on the charger (Ionity, Shell Recharge, Allego, etc.). Download their app if you do not have it, add a payment method, and start the session through the app. Make sure you select the correct stall number shown on the charger.

3. 3

   Try a different RFID card or payment method

   If you carry multiple charging cards, try a different one. Some roaming cards work across many networks. If you only have one card, try contactless payment with your bank card or phone if the charger supports it.

4. 4

   Check your bank card's available balance

   Open your banking app and check that you have enough available balance for the pre-authorization hold, which can be up to 50 EUR even for a short charge. Pending holds from previous charging sessions can temporarily reduce your available balance.

5. 5

   Restart the charger and try again

   Some chargers have a stop/reset button. Press it, wait for the screen to return to the start screen, then begin a fresh session. If there is no button, unplug your Polestar 2, wait 30 seconds, and replug.

6. 6

   Move to a different charger

   If nothing works at this stall, try a different stall at the same station. Payment terminals can fail independently. If the entire station is down, find the nearest alternative using the charger map on your Polestar 2 center display or Google Maps.

Polestar 2 Charging Slower Than Expected

You plugged in your Polestar 2 expecting 149 kW and the screen shows 40 kW. Or your home charger is stuck at 3 kW instead of 11 kW. Slow charging on the Polestar 2 is almost never a defect. It is usually the battery temperature, the charger itself, or a setting you can fix in two minutes.

Symptoms

• DC fast charging speed well below the 149 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops significantly after reaching 50-60%
• Charging session starts normally but slows down quickly
• Dashboard shows lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature

   Look at the charging screen on the center display. If the battery is cold (common in winter), drive for 15-20 minutes before charging or use the preconditioning feature through the Polestar app before arriving at the charger.

2. 2

   Check your state of charge

   If you are above 80%, the slower speed is normal. For fastest charging, arrive at the charger between 10-20% and charge to 80%.

3. 3

   Verify the charger is not shared

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if available.

4. 4

   Check the AC charge current setting

   In the Polestar 2, go to Settings, then Charging. Make sure the charge current limiter is set to maximum. If it shows a lower value, increase it.

5. 5

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Try a different charger at the same location or a different charging station.

RFID card not recognized at the charger

You tap your Shell Recharge RFID card on the charger's reader but it does not respond, beeps an error, or shows 'Card not recognized.'

Symptoms

• Charger beeps but displays 'Unknown card' or 'Authorization failed'
• No response at all when tapping the card
• Card works at some stations but not others
• Card worked yesterday at the same charger but does not work today

How to Fix It

1. 1

   Hold the card still on the reader for 3 to 5 seconds

   RFID readers at some chargers are slow. Do not tap and remove quickly. Hold the card flat against the reader and wait for a confirmation beep or screen change.

2. 2

   Check that your RFID card is activated

   New Shell Recharge RFID cards must be activated in the Shell Recharge app before first use. Go to the app, find the RFID section, and make sure the card status shows active.

3. 3

   Try starting the session through the app instead

   Open the Shell Recharge app, find the station, select the charger, and start the session digitally. This bypasses the RFID reader entirely and uses the roaming connection.

4. 4

   Check if the CPO supports Shell Recharge roaming

   Not every charger that appears in the Shell Recharge app accepts the Shell Recharge RFID card. Some chargers only accept app-based roaming. The station details in the app usually indicate which payment methods are supported.

5. 5

   Clean the card and try again

   Dirt, scratches, or a phone case between the card and reader can block the RFID signal. Remove the card from any holder, wipe it, and try again on the reader's sweet spot (often marked with a contactless symbol).

Roaming vs direct pricing confusion

The price you pay through Shell Recharge is different from the price shown on the charger's screen. This is because Shell Recharge adds a roaming markup on top of the CPO's base rate.

Symptoms

• Charger screen shows 0.39 EUR/kWh but Shell Recharge bills 0.55 EUR/kWh
• Invoice includes fees not displayed at the charger (session fee, per-minute fee)
• Same station is cheaper when using the CPO's own app
• Pricing in the Shell Recharge app does not match the final invoice

How to Fix It

1. 1

   Check the Shell Recharge app for the roaming price before starting

   Before you tap your card or start a session, open the Shell Recharge app and select the station. The app shows the Shell Recharge price, which includes any roaming fee. This is the price you will actually pay.

2. 2

   Understand the pricing structure

   Shell Recharge typically charges a per-kWh rate plus sometimes a session start fee or per-minute fee. The charger screen shows the CPO's direct price, not the roaming price. These are two different rates for two different billing relationships.

3. 3

   Consider using the CPO's own app for lower rates

   If you charge at the same network regularly (for example, Allego, Fastned, or EnBW), their own app usually offers a lower price than roaming through Shell Recharge. The trade-off is managing multiple apps.

4. 4

   Download your invoice from the Shell Recharge app

   Go to your charging history in the Shell Recharge app. Each session has a detailed breakdown showing energy delivered, per-kWh rate, session fees, and total cost. Compare this with what you expected.

Session not starting via QR code

You scan the QR code on the charger to start a session through the Shell Recharge app, but nothing happens or you get an error.

Symptoms

• QR code opens the Shell Recharge app but shows 'Station not found'
• QR code opens a web page instead of the app
• App shows 'Unable to start session' after scanning
• QR code is faded, damaged, or partially covered by a sticker

How to Fix It

1. 1

   Search for the station manually in the app

   If the QR code does not work, open the Shell Recharge app, search for the station by name or location, and start the session from the station page. You may need to select the specific connector or charger ID.

2. 2

   Check the charger ID number

   Every charger has an ID printed somewhere on the unit (usually near the QR code or on a label). Enter this ID manually in the Shell Recharge app if the QR scan fails.

3. 3

   Make sure the QR code belongs to Shell Recharge

   Many chargers have multiple QR codes from different roaming providers and the CPO itself. Make sure you are scanning the Shell Recharge QR code, not the CPO's own code. Scanning the wrong code opens the wrong app or website.

4. 4

   Try the RFID card or contactless payment instead

   QR code start is just one method. Tap your Shell Recharge RFID card or use contactless payment if the charger supports it.

5. 5

   Check your internet connection

   Starting a session via QR code requires the app to communicate with Shell Recharge's servers and the CPO's backend. If you have weak mobile signal (common at highway rest stops), the request may time out. Try switching between Wi-Fi and mobile data.

App showing wrong charger status

The Shell Recharge app shows a charger as available, occupied, or offline, but the actual status is different when you arrive.

Symptoms

• App shows 'Available' but the charger is out of order or has an error screen
• App shows 'Occupied' but no vehicle is connected
• Status has not updated for hours and seems stale
• App shows fewer chargers at a station than physically exist

How to Fix It

1. 1

   Understand that status data is delayed

   Shell Recharge gets charger status from the CPO's systems through the roaming connection. This data can lag by 5 to 15 minutes. A charger that just became available may still show as occupied in the app.

2. 2

   Try plugging in regardless of app status

   If you are already at the station and a charger looks physically available (no vehicle connected, no error on screen), try plugging in and starting a session. The real-time status at the charger overrides whatever the app shows.

3. 3

   Check the CPO's own app for more accurate status

   The CPO (the company that actually operates the charger) usually has more accurate real-time status than roaming aggregators like Shell Recharge. If accuracy matters, cross-check with the CPO's app or website.

4. 4

   Report the incorrect status

   Use the Shell Recharge app to report the charger issue. This helps improve status accuracy over time.

Billing discrepancy between Shell Recharge and the CPO

The amount billed by Shell Recharge does not match what you expected based on the energy delivered or the session duration. This can happen because of how roaming billing works.

Symptoms

• Billed for more kWh than your vehicle's dashboard shows
• Charged a session fee you did not expect
• Per-minute idle fee added even though you unplugged on time
• Double charge: both Shell Recharge and the CPO billed you

How to Fix It

1. 1

   Compare the Shell Recharge invoice with your vehicle's data

   Your vehicle's dashboard shows how much energy the battery received. The charger meters how much energy it delivered, which includes conversion losses. A 5 to 10% difference is normal.

2. 2

   Check for per-minute fees

   Some CPOs charge a per-minute fee (for time spent connected) on top of the per-kWh fee. This can be especially costly during slow AC charging sessions. Check the pricing breakdown in the Shell Recharge app.

3. 3

   Look for session or start fees

   Some stations add a fixed fee per session (for example, 0.35 EUR to 1.00 EUR). This appears in the Shell Recharge invoice as a separate line item.

4. 4

   Dispute the charge through the Shell Recharge app

   If the amount is clearly wrong (double billed, charged for a session that never started, or obviously excessive), contact Shell Recharge support through the app. Go to your charging history, select the session, and use the dispute or help option.

5. 5

   Keep your vehicle's charge data as evidence

   Take a photo of your vehicle's charging screen or dashboard showing the kWh received and the session duration. This is useful if you need to dispute a charge.