Polestar 2 Charging at Recharge

Polestar 2 Charger Won't Start or Begin Charging

You have plugged in your Polestar 2, the connector clicked, but nothing happens. The center display stays silent or shows an error. This is frustrating, but it is almost always fixable on the spot without calling support.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the center display
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• Polestar 2 charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Center display briefly shows charging screen, then returns to idle

What to Do

1. 1

   Unplug and reconnect firmly

   Remove the CCS2 or Type 2 connector, wait 10 seconds, then reinsert it with a firm push until you hear a clear click. Watch the charge port LED on the Polestar 2 for a steady light.

2. 2

   Check for a charging schedule

   On the center display, go to Settings, then Charging. If a charging schedule is active, disable it or set it to 'Direct' so the car charges immediately when plugged in.

3. 3

   Restart the charger session

   On the charger, end the current session if one is shown. Then start a new session by tapping your RFID card or restarting in the charger's app. Some chargers have a physical start/stop button.

4. 4

   Try Plug & Charge or a different payment method

   If your Polestar 2 has Plug & Charge enabled, check the charger supports it. Otherwise, switch to a different RFID card, contactless payment, or the charger operator's app.

5. 5

   Reboot the car's infotainment system

   Press and hold the home button on the center display for about 15 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication module.

6. 6

   Try a different charger or cable

   If the station has multiple stalls, move to a different one. If you are using a tethered cable, try bringing your own Type 2 cable. A faulty charger cable is more common than a faulty car.

Polestar 2 Charging Payment Failed at the Station

You are at the charger, your Polestar 2 is ready, but the payment will not go through. The charger says 'Authorization failed' or just does nothing after you tap your card. Payment issues are one of the most common reasons a charging session never starts, and they are usually fixable in a couple of minutes.

Symptoms

• Charger screen shows 'Authorization failed' or 'Payment declined' after tapping your card or RFID
• Charger app shows an error when trying to start a remote session for your Polestar 2
• Contactless bank card is declined even though it works at shops
• Plug & Charge does not activate automatically after plugging in the CCS2 connector
• Charger accepts payment but the session immediately ends with a zero-kWh charge

What to Do

1. 1

   Check if Plug & Charge is enabled

   On the Polestar 2 center display, go to Settings, then Charging. Confirm Plug & Charge is turned on. If it is on but the charger did not start automatically, this station likely does not support it. Use a different payment method.

2. 2

   Try the charger operator's app

   Look for the operator name on the charger (Ionity, Shell Recharge, Allego, etc.). Download their app if you do not have it, add a payment method, and start the session through the app. Make sure you select the correct stall number shown on the charger.

3. 3

   Try a different RFID card or payment method

   If you carry multiple charging cards, try a different one. Some roaming cards work across many networks. If you only have one card, try contactless payment with your bank card or phone if the charger supports it.

4. 4

   Check your bank card's available balance

   Open your banking app and check that you have enough available balance for the pre-authorization hold, which can be up to 50 EUR even for a short charge. Pending holds from previous charging sessions can temporarily reduce your available balance.

5. 5

   Restart the charger and try again

   Some chargers have a stop/reset button. Press it, wait for the screen to return to the start screen, then begin a fresh session. If there is no button, unplug your Polestar 2, wait 30 seconds, and replug.

6. 6

   Move to a different charger

   If nothing works at this stall, try a different stall at the same station. Payment terminals can fail independently. If the entire station is down, find the nearest alternative using the charger map on your Polestar 2 center display or Google Maps.

Polestar 2 Charging Slower Than Expected

You plugged in your Polestar 2 expecting 149 kW and the screen shows 40 kW. Or your home charger is stuck at 3 kW instead of 11 kW. Slow charging on the Polestar 2 is almost never a defect. It is usually the battery temperature, the charger itself, or a setting you can fix in two minutes.

Symptoms

• DC fast charging speed well below the 149 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops significantly after reaching 50-60%
• Charging session starts normally but slows down quickly
• Dashboard shows lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature

   Look at the charging screen on the center display. If the battery is cold (common in winter), drive for 15-20 minutes before charging or use the preconditioning feature through the Polestar app before arriving at the charger.

2. 2

   Check your state of charge

   If you are above 80%, the slower speed is normal. For fastest charging, arrive at the charger between 10-20% and charge to 80%.

3. 3

   Verify the charger is not shared

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if available.

4. 4

   Check the AC charge current setting

   In the Polestar 2, go to Settings, then Charging. Make sure the charge current limiter is set to maximum. If it shows a lower value, increase it.

5. 5

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Try a different charger at the same location or a different charging station.

Charger stuck in "preparing" state

You authenticated successfully, the charger says "preparing," but it never starts delivering power. This is one of the most reported issues on Recharge stations, especially at older units.

Symptoms

• Charger screen shows "Preparing" or "Initializing" for more than two minutes
• Your car's charging indicator does not activate
• The Recharge app shows the session as active but 0 kW delivered
• The charger fan spins up but no power flows

How to Fix It

1. 1

   Wait up to three minutes

   Some Recharge units, particularly the 300kW stations, take longer to complete the power handshake with your car. Give it a full three minutes before taking action.

2. 2

   Unplug and reconnect

   Remove the CCS2 connector, wait 15 seconds, then plug it back in firmly. This resets the communication between your car and the charger.

3. 3

   Stop the session in the Recharge app and start a new one

   Open the Recharge app, tap Stop on the active session, wait for it to fully end, then start a new session on the same charger. This clears any stuck state on the backend.

4. 4

   Try the other connector on the same unit

   Many Recharge stations have two CCS2 connectors. If one is stuck, the other connector on the same unit often works fine.

5. 5

   Use a different authentication method

   If you started with the app, try your RFID card instead, or vice versa. Sometimes the issue is with the authentication path, not the charger hardware.

Old Fortum branding causes app scan failure

Recharge was originally part of Fortum's charging operations before being spun off as a separate company. Some older stations still display Fortum logos and QR codes. Scanning an old Fortum QR code with the Recharge app may not work, or it may redirect to a dead Fortum page.

Symptoms

• QR code on the charger opens a Fortum website or shows an error
• Recharge app says "Charger not found" after scanning
• Station ID on the physical unit does not match what the Recharge app expects
• The charger has Fortum branding but is listed as Recharge in third-party apps

How to Fix It

1. 1

   Ignore the QR code and search by station name in the Recharge app

   Open the Recharge app, use the map or search to find the station by location. The charger will appear under its Recharge name even if the physical unit still says Fortum.

2. 2

   Enter the charger ID manually

   Look for a numeric ID on the charger, often printed on a sticker near the connector. In the Recharge app, tap "Enter ID" and type it in directly.

3. 3

   Use RFID or contactless payment instead of the app

   Tap your Recharge RFID card or a contactless bank card on the reader. This bypasses the app entirely and works regardless of the branding on the charger.

4. 4

   Check if contactless is available on this unit

   Not all Recharge stations support contactless bank card payment. Look for a card reader terminal on the charger. If there is no terminal, you will need the app or an RFID card.

RFID card from old Fortum account not recognized

If you had a Fortum Charge & Drive account and RFID card, it may not work automatically on the Recharge network. Some cards were migrated, others were not.

Symptoms

• Tapping your old Fortum RFID card shows "Card not recognized" on the charger
• The charger beeps but does not start a session
• Your Fortum card works on some stations but not others

How to Fix It

1. 1

   Log in to the Recharge app and check your RFID cards

   Open the Recharge app, go to your account settings, and look under RFID cards. If your old Fortum card is not listed, it was not migrated automatically.

2. 2

   Re-register your RFID card

   In the Recharge app, tap "Add RFID card" and follow the steps. You will need the card number printed on the back of your RFID card.

3. 3

   Use the app to start the session while you wait for RFID activation

   RFID card registration can take up to 24 hours to propagate across all stations. Use the app to authenticate in the meantime.

4. 4

   Order a new Recharge RFID card if re-registration fails

   Some older Fortum cards use a chip format that is not compatible. You can order a new Recharge RFID card through the app or website.

Contactless payment not accepted

You are trying to tap your bank card or phone to pay, but the charger does not respond or shows an error. Contactless payment availability varies across Recharge stations.

Symptoms

• No card reader terminal visible on the charger
• Card reader shows "Payment failed" or does not respond to taps
• Apple Pay or Google Pay not recognized
• The charger prompts for an RFID card but you only have a bank card

How to Fix It

1. 1

   Check if this station supports contactless payment

   Look for a separate payment terminal with a contactless symbol. Not all Recharge stations have been upgraded. The Recharge app shows payment options for each station on the station detail page.

2. 2

   Try removing and re-holding your card

   Hold your card flat against the reader for at least three seconds. Some terminals need a longer hold than you might expect. Remove the card fully, then try again.

3. 3

   Fall back to the Recharge app

   If contactless is not working, open the Recharge app and start the session from there. You need a payment method saved in the app.

4. 4

   Try a different card

   Some Visa Electron and certain prepaid cards are not accepted by the payment terminals. A standard Visa or Mastercard debit or credit card usually works.

Charging speed much lower than expected

The station is rated for 300kW, but your car is only pulling 50kW or less. While your car's battery management limits the maximum speed, Recharge stations can also throttle power.

Symptoms

• Charger display shows far less power than the station's rated capacity
• Charging speed drops suddenly mid-session
• Other cars at the same station are also charging slowly
• The Recharge app shows the session but at low power

How to Fix It

1. 1

   Check how many other cars are charging at the same station

   Recharge stations with multiple connectors often share a power cabinet. If two or three cars are charging simultaneously, the available power per car drops. This is normal and not a fault.

2. 2

   Check your battery level

   DC fast charging slows significantly above 80% on most EVs. If your battery is above 70-80%, the slower speed is your car protecting the battery, not a problem with the Recharge station.

3. 3

   Check the temperature

   In cold weather, your car may limit charging speed until the battery warms up. This can take 10-15 minutes of charging before speeds increase. Some cars precondition the battery if you set the charger as a destination in navigation.

4. 4

   Try a different connector at the station

   Individual connectors can have faults that limit power output. If another connector is free, unplug and try it.

5. 5

   Report the issue in the Recharge app

   If the speed is unusually low and none of the above apply, report it through the Recharge app. Tap the active session and look for a "Report issue" option. This helps Recharge identify hardware problems.