Tesla Model 3 Charging at Shell Recharge

Tesla Model 3 Charger Won't Start a Charging Session

You have plugged in your Model 3, the charge port light is doing something weird, and nothing is happening. This is one of the most common frustrations for EV drivers. The good news is that it is almost always fixable on the spot. The cause is usually authentication, the charge port latch, or the charger itself.

Symptoms

• Charge port LED flashes amber or red after plugging in the CCS2 connector
• Touchscreen shows an error message instead of the charging screen
• Charger display says 'Waiting for vehicle' or 'Authentication failed'
• Charge port will not open when pressing the button on the connector
• Supercharger session does not start automatically after plugging in

What to Do

1. 1

   Unplug and replug the connector firmly

   Pull the connector out completely. Wait 5 seconds. Push it back in firmly until you hear a click and the charge port LED turns green or starts pulsing. On CCS2, the lower DC pins need to seat fully.

2. 2

   Check the touchscreen for error messages

   Look at the charging screen on the touchscreen. It will tell you if there is an error, if scheduled charging is active, or if the car is waiting for something. If Scheduled Charging is delaying the session, tap 'Charge Now' to override it.

3. 3

   Authenticate with the charging network

   At non-Tesla chargers, open the network's app (Ionity, Shell Recharge, or whichever network). Start the session through the app, or tap your RFID card on the charger. At Tesla Superchargers, this step is automatic.

4. 4

   Try the manual charge port release if the port is stuck

   If the charge port will not open, try tapping your Tesla key card on the B-pillar and pressing the charge port door. You can also open it from the touchscreen under Controls. In freezing weather, pour lukewarm water around the port to melt ice. Never force it.

5. 5

   Restart the touchscreen

   Hold both scroll wheels on the steering wheel for about 10 seconds until the Tesla logo appears. This restarts the infotainment system and can clear communication errors between the car and the charger.

6. 6

   Try a different charger or stall

   If nothing works, the charger may be faulty. Move to a different stall or station. At Superchargers, the Tesla app shows stall availability in real time.

Tesla Model 3 Payment Failed at the Charging Station

You plugged in, everything looked fine, and then the charger says payment failed. Or the session will not start because authentication did not go through. Payment problems are different at Tesla Superchargers versus non-Tesla CCS2 chargers, so the fix depends on where you are.

Symptoms

• Charger display shows 'Payment failed' or 'Transaction declined' after tapping a card
• Tesla Supercharger session will not start and the Tesla app shows a billing error
• Non-Tesla CCS2 charger shows 'Authentication failed' after scanning RFID or using an app
• Contactless payment terminal on the charger does not respond to your bank card
• Charging starts but stops after a few seconds with a payment-related error on the charger screen

What to Do

1. 1

   Check if this is a Tesla Supercharger or a non-Tesla station

   At Tesla Superchargers, payment is automatic through your Tesla account. At non-Tesla CCS2 chargers, you need to authenticate separately. The fix is completely different for each.

2. 2

   For Superchargers: update your payment method in the Tesla app

   Open the Tesla app, go to Account, then Payment. Check that your card is current and not expired. Add a new card if needed. Then try the Supercharger again. The session should start automatically after plugging in.

3. 3

   For non-Tesla chargers: authenticate through the network app

   Open the charging network's app (Ionity, Shell Recharge, Virta, or whichever network runs the charger). Select the charger, start the session, then plug in. Make sure the app shows your payment method is valid.

4. 4

   Try a different payment method at the charger

   If the contactless terminal failed, try the network's app instead. If the app failed, try an RFID card. If you do not have the network's app, some chargers accept ad-hoc payments through a QR code on the charger.

5. 5

   Call your bank if repeated transactions are declined

   If your card keeps getting declined at chargers, your bank may be blocking charging transactions. Call the number on the back of your card and let them know you are making EV charging payments. They can whitelist these merchants.

6. 6

   Move to a different charger if the payment terminal is broken

   If the charger's payment terminal is physically unresponsive, try a different stall. Report the broken terminal through the network's app so they can fix it.

Tesla Model 3 Charging Slower Than Expected at Charger

You plugged in your Model 3 expecting 175 kW and the touchscreen shows 50 kW. Or your home wallbox is stuck at 3 kW instead of 11 kW. Slow charging on the Model 3 is almost never a defect. It is usually the battery temperature, a charger limitation, or a setting you can fix on the touchscreen in under a minute.

Symptoms

• DC fast charging power well below the 175 kW maximum shown on the touchscreen
• AC home charging stuck at 3-4 kW instead of the expected 11 kW
• Charging speed drops sharply after reaching 50-60% on the touchscreen
• Supercharger shows lower kW than the stall is rated for
• Touchscreen charging animation shows a slow trickle instead of rapid charging

What to Do

1. 1

   Check the battery temperature on the touchscreen

   Tap the charging icon on the touchscreen. If the battery is cold, you will see a snowflake icon or a message about reduced charging speed. To fix this, use the Tesla nav to route to a Supercharger. The car will automatically precondition the battery during the drive.

2. 2

   Check your state of charge

   If you are above 80%, the slower speed is expected. For the fastest DC charging, arrive between 10-20%. The Model 3 LFP hits peak power in the 10-50% range.

3. 3

   Move to an unpaired Supercharger stall

   Look at the stall numbers. If they are labeled in pairs (1A/1B, 2A/2B), pick a stall where the paired stall is empty. At V3 or V4 Superchargers, this is not an issue.

4. 4

   Check the AC charge current limit

   On the touchscreen, go to Controls, then Charging. Look for the charge current slider or setting. Make sure it is set to the maximum value. This only affects AC charging, not Supercharging.

5. 5

   Try a different charger or stall

   If speeds are still low, the charger may be degraded. Try a different stall at the same location. On non-Tesla CCS chargers, some stations deliver less power than advertised.

6. 6

   Check for a software update

   Go to Controls, then Software on the touchscreen. If an update is available, install it. Tesla occasionally adjusts charging curves through software updates.

RFID card not recognized at the charger

You tap your Shell Recharge RFID card on the charger's reader but it does not respond, beeps an error, or shows 'Card not recognized.'

Symptoms

• Charger beeps but displays 'Unknown card' or 'Authorization failed'
• No response at all when tapping the card
• Card works at some stations but not others
• Card worked yesterday at the same charger but does not work today

How to Fix It

1. 1

   Hold the card still on the reader for 3 to 5 seconds

   RFID readers at some chargers are slow. Do not tap and remove quickly. Hold the card flat against the reader and wait for a confirmation beep or screen change.

2. 2

   Check that your RFID card is activated

   New Shell Recharge RFID cards must be activated in the Shell Recharge app before first use. Go to the app, find the RFID section, and make sure the card status shows active.

3. 3

   Try starting the session through the app instead

   Open the Shell Recharge app, find the station, select the charger, and start the session digitally. This bypasses the RFID reader entirely and uses the roaming connection.

4. 4

   Check if the CPO supports Shell Recharge roaming

   Not every charger that appears in the Shell Recharge app accepts the Shell Recharge RFID card. Some chargers only accept app-based roaming. The station details in the app usually indicate which payment methods are supported.

5. 5

   Clean the card and try again

   Dirt, scratches, or a phone case between the card and reader can block the RFID signal. Remove the card from any holder, wipe it, and try again on the reader's sweet spot (often marked with a contactless symbol).

Roaming vs direct pricing confusion

The price you pay through Shell Recharge is different from the price shown on the charger's screen. This is because Shell Recharge adds a roaming markup on top of the CPO's base rate.

Symptoms

• Charger screen shows 0.39 EUR/kWh but Shell Recharge bills 0.55 EUR/kWh
• Invoice includes fees not displayed at the charger (session fee, per-minute fee)
• Same station is cheaper when using the CPO's own app
• Pricing in the Shell Recharge app does not match the final invoice

How to Fix It

1. 1

   Check the Shell Recharge app for the roaming price before starting

   Before you tap your card or start a session, open the Shell Recharge app and select the station. The app shows the Shell Recharge price, which includes any roaming fee. This is the price you will actually pay.

2. 2

   Understand the pricing structure

   Shell Recharge typically charges a per-kWh rate plus sometimes a session start fee or per-minute fee. The charger screen shows the CPO's direct price, not the roaming price. These are two different rates for two different billing relationships.

3. 3

   Consider using the CPO's own app for lower rates

   If you charge at the same network regularly (for example, Allego, Fastned, or EnBW), their own app usually offers a lower price than roaming through Shell Recharge. The trade-off is managing multiple apps.

4. 4

   Download your invoice from the Shell Recharge app

   Go to your charging history in the Shell Recharge app. Each session has a detailed breakdown showing energy delivered, per-kWh rate, session fees, and total cost. Compare this with what you expected.

Session not starting via QR code

You scan the QR code on the charger to start a session through the Shell Recharge app, but nothing happens or you get an error.

Symptoms

• QR code opens the Shell Recharge app but shows 'Station not found'
• QR code opens a web page instead of the app
• App shows 'Unable to start session' after scanning
• QR code is faded, damaged, or partially covered by a sticker

How to Fix It

1. 1

   Search for the station manually in the app

   If the QR code does not work, open the Shell Recharge app, search for the station by name or location, and start the session from the station page. You may need to select the specific connector or charger ID.

2. 2

   Check the charger ID number

   Every charger has an ID printed somewhere on the unit (usually near the QR code or on a label). Enter this ID manually in the Shell Recharge app if the QR scan fails.

3. 3

   Make sure the QR code belongs to Shell Recharge

   Many chargers have multiple QR codes from different roaming providers and the CPO itself. Make sure you are scanning the Shell Recharge QR code, not the CPO's own code. Scanning the wrong code opens the wrong app or website.

4. 4

   Try the RFID card or contactless payment instead

   QR code start is just one method. Tap your Shell Recharge RFID card or use contactless payment if the charger supports it.

5. 5

   Check your internet connection

   Starting a session via QR code requires the app to communicate with Shell Recharge's servers and the CPO's backend. If you have weak mobile signal (common at highway rest stops), the request may time out. Try switching between Wi-Fi and mobile data.

App showing wrong charger status

The Shell Recharge app shows a charger as available, occupied, or offline, but the actual status is different when you arrive.

Symptoms

• App shows 'Available' but the charger is out of order or has an error screen
• App shows 'Occupied' but no vehicle is connected
• Status has not updated for hours and seems stale
• App shows fewer chargers at a station than physically exist

How to Fix It

1. 1

   Understand that status data is delayed

   Shell Recharge gets charger status from the CPO's systems through the roaming connection. This data can lag by 5 to 15 minutes. A charger that just became available may still show as occupied in the app.

2. 2

   Try plugging in regardless of app status

   If you are already at the station and a charger looks physically available (no vehicle connected, no error on screen), try plugging in and starting a session. The real-time status at the charger overrides whatever the app shows.

3. 3

   Check the CPO's own app for more accurate status

   The CPO (the company that actually operates the charger) usually has more accurate real-time status than roaming aggregators like Shell Recharge. If accuracy matters, cross-check with the CPO's app or website.

4. 4

   Report the incorrect status

   Use the Shell Recharge app to report the charger issue. This helps improve status accuracy over time.

Billing discrepancy between Shell Recharge and the CPO

The amount billed by Shell Recharge does not match what you expected based on the energy delivered or the session duration. This can happen because of how roaming billing works.

Symptoms

• Billed for more kWh than your vehicle's dashboard shows
• Charged a session fee you did not expect
• Per-minute idle fee added even though you unplugged on time
• Double charge: both Shell Recharge and the CPO billed you

How to Fix It

1. 1

   Compare the Shell Recharge invoice with your vehicle's data

   Your vehicle's dashboard shows how much energy the battery received. The charger meters how much energy it delivered, which includes conversion losses. A 5 to 10% difference is normal.

2. 2

   Check for per-minute fees

   Some CPOs charge a per-minute fee (for time spent connected) on top of the per-kWh fee. This can be especially costly during slow AC charging sessions. Check the pricing breakdown in the Shell Recharge app.

3. 3

   Look for session or start fees

   Some stations add a fixed fee per session (for example, 0.35 EUR to 1.00 EUR). This appears in the Shell Recharge invoice as a separate line item.

4. 4

   Dispute the charge through the Shell Recharge app

   If the amount is clearly wrong (double billed, charged for a session that never started, or obviously excessive), contact Shell Recharge support through the app. Go to your charging history, select the session, and use the dispute or help option.

5. 5

   Keep your vehicle's charge data as evidence

   Take a photo of your vehicle's charging screen or dashboard showing the kWh received and the session duration. This is useful if you need to dispute a charge.