BMW i4 Charging at Shell Recharge

BMW i4 Charger Won't Start? Step-by-Step Solutions

You've plugged in the CCS2 cable to your BMW i4's right rear charge port, but nothing happens. This is one of the most common frustrations at public chargers. The good news is that most causes are fixable on the spot.

Symptoms

• CCS2 connector is plugged into the right rear port but the charger screen shows no vehicle detected
• Charger displays an error code and refuses to start the session
• My BMW app shows the car is plugged in but not charging
• The charge port LED on the i4 flashes or stays amber instead of turning blue
• Authentication via app or RFID card goes through but charging never begins

What to Do

1. 1

   Unplug the CCS2 cable and reseat it firmly

   Pull the connector out completely. Check the pins for debris or damage. Line it up straight with the charge port on the right rear and push until you hear a clear click. The charge port LED should respond.

2. 2

   Check the charge port LED color on the car

   Blue pulsing means the car is ready to charge. Amber or yellow means something is wrong on the car side. No light at all may mean the port isn't detecting the cable. Open the My BMW app for more detail.

3. 3

   Disable any charging schedule in iDrive

   On the iDrive curved display, go to the charging settings and check for active schedules or departure times. Disable scheduled charging temporarily if you want to charge immediately at a public station.

4. 4

   Try authenticating again or use a different method

   If Plug & Charge didn't start the session, open the charging network's app and start manually. If the app fails, try an RFID card. If you're using BMW Charging, check that your payment method is current in the My BMW app.

5. 5

   Restart the charger if possible

   Some chargers have a stop/reset button on the screen. Unplug, wait 30 seconds, and try again. If the charger has two cables, try the other connector. Check the charger's screen for error messages or an out-of-service notice.

6. 6

   Move to a different charger if the problem persists

   If nothing works after two attempts, the charger is likely faulty. Use the My BMW app or a charging map to find the next nearest station. Report the broken charger through the network's app to help other drivers.

BMW i4 Charging Payment Failed? How to Fix It Now

You're at the charger, the CCS2 cable is plugged into your BMW i4, but payment won't go through. Maybe Plug & Charge didn't kick in, the app is throwing errors, or your card was declined. Here's how to sort it out and start charging.

Symptoms

• Plug & Charge doesn't activate when you connect the CCS2 cable
• BMW Charging shows a payment error in the My BMW app
• The charger screen says authentication failed or payment declined
• Your RFID card is not recognized at this charging station
• Contactless card payment at the charger terminal is rejected

What to Do

1. 1

   Check if Plug & Charge is set up in the My BMW app

   Open the My BMW app, go to your charging settings, and verify that Plug & Charge is enabled and linked to an active payment method. If you see a setup prompt, complete it before trying again.

2. 2

   Update your payment method in BMW Charging

   In the My BMW app, navigate to your BMW Charging account and check your stored payment card. Update it if it's expired or recently replaced. The change should take effect within a few minutes.

3. 3

   Try the charging network's own app

   Identify which company operates the charger (the logo is usually on the unit). Download their app, create an account, add a payment method, and start the session through their app instead of BMW Charging.

4. 4

   Use a different RFID card or contactless payment

   If you have another RFID card from a different network, try that. Some chargers also accept contactless debit or credit cards. Look for a payment terminal on the charger, usually near the screen.

5. 5

   Try a different charger at the same station or a nearby station

   Sometimes a single charger's payment terminal malfunctions while others work fine. Try the next unit over. If the whole station is problematic, use iDrive navigation to find an alternative station nearby.

BMW i4 Charging Slower Than Expected? Fixes Here

Your BMW i4 eDrive40 supports up to 205 kW DC fast charging, but real-world speeds often fall short. Several factors specific to the i4's 80.7 kWh battery and 400V architecture can limit charging power. Here's how to diagnose and fix slow charging on your i4.

Symptoms

• DC charging speed stays well below 205 kW even at a high-power charger
• Charging curve drops sharply before reaching 60% state of charge
• AC charging at home or destination chargers maxes out at 3.6 kW instead of 11 kW
• iDrive curved display shows a lower charging rate than the charger's rated output
• Estimated charging time on the iDrive screen is much longer than expected

What to Do

1. 1

   Use iDrive navigation to route to your charging stop

   Enter the charging station as a waypoint or destination in iDrive. The i4 will automatically precondition the battery while you drive, warming it to the ideal temperature for fast charging. This alone can double your charging speed in cold weather.

2. 2

   Arrive at the charger with a lower state of charge

   The i4 charges fastest between 10% and 50%. If possible, plan your stop so you arrive closer to 10-20%. The difference between arriving at 15% versus 50% can save significant time.

3. 3

   Choose a charger stall that isn't sharing power

   Look at the charger setup. If two CCS2 cables come from one cabinet, pick a stall where the neighboring connector is free. Some stations label paired stalls with A/B designations.

4. 4

   Check your AC charging setup at home

   Open the My BMW app and look at the charging details during an AC session. If you're only getting 3.6 kW, your installation likely provides single-phase power. Ask your electrician about a three-phase connection to unlock the full 11 kW.

5. 5

   Check the charging status on the iDrive curved display

   While charging, the iDrive screen shows current power, estimated time remaining, and battery temperature. If power is low and battery temperature is also low, the car is still warming the pack. Give it a few minutes to ramp up.

6. 6

   Unplug at 80% and drive to the next charger if needed

   Charging from 80% to 100% on DC can take as long as 10% to 80%. On road trips, it's almost always faster to charge to 80%, drive, and stop again rather than waiting for a full charge.

RFID card not recognized at the charger

You tap your Shell Recharge RFID card on the charger's reader but it does not respond, beeps an error, or shows 'Card not recognized.'

Symptoms

• Charger beeps but displays 'Unknown card' or 'Authorization failed'
• No response at all when tapping the card
• Card works at some stations but not others
• Card worked yesterday at the same charger but does not work today

How to Fix It

1. 1

   Hold the card still on the reader for 3 to 5 seconds

   RFID readers at some chargers are slow. Do not tap and remove quickly. Hold the card flat against the reader and wait for a confirmation beep or screen change.

2. 2

   Check that your RFID card is activated

   New Shell Recharge RFID cards must be activated in the Shell Recharge app before first use. Go to the app, find the RFID section, and make sure the card status shows active.

3. 3

   Try starting the session through the app instead

   Open the Shell Recharge app, find the station, select the charger, and start the session digitally. This bypasses the RFID reader entirely and uses the roaming connection.

4. 4

   Check if the CPO supports Shell Recharge roaming

   Not every charger that appears in the Shell Recharge app accepts the Shell Recharge RFID card. Some chargers only accept app-based roaming. The station details in the app usually indicate which payment methods are supported.

5. 5

   Clean the card and try again

   Dirt, scratches, or a phone case between the card and reader can block the RFID signal. Remove the card from any holder, wipe it, and try again on the reader's sweet spot (often marked with a contactless symbol).

Roaming vs direct pricing confusion

The price you pay through Shell Recharge is different from the price shown on the charger's screen. This is because Shell Recharge adds a roaming markup on top of the CPO's base rate.

Symptoms

• Charger screen shows 0.39 EUR/kWh but Shell Recharge bills 0.55 EUR/kWh
• Invoice includes fees not displayed at the charger (session fee, per-minute fee)
• Same station is cheaper when using the CPO's own app
• Pricing in the Shell Recharge app does not match the final invoice

How to Fix It

1. 1

   Check the Shell Recharge app for the roaming price before starting

   Before you tap your card or start a session, open the Shell Recharge app and select the station. The app shows the Shell Recharge price, which includes any roaming fee. This is the price you will actually pay.

2. 2

   Understand the pricing structure

   Shell Recharge typically charges a per-kWh rate plus sometimes a session start fee or per-minute fee. The charger screen shows the CPO's direct price, not the roaming price. These are two different rates for two different billing relationships.

3. 3

   Consider using the CPO's own app for lower rates

   If you charge at the same network regularly (for example, Allego, Fastned, or EnBW), their own app usually offers a lower price than roaming through Shell Recharge. The trade-off is managing multiple apps.

4. 4

   Download your invoice from the Shell Recharge app

   Go to your charging history in the Shell Recharge app. Each session has a detailed breakdown showing energy delivered, per-kWh rate, session fees, and total cost. Compare this with what you expected.

Session not starting via QR code

You scan the QR code on the charger to start a session through the Shell Recharge app, but nothing happens or you get an error.

Symptoms

• QR code opens the Shell Recharge app but shows 'Station not found'
• QR code opens a web page instead of the app
• App shows 'Unable to start session' after scanning
• QR code is faded, damaged, or partially covered by a sticker

How to Fix It

1. 1

   Search for the station manually in the app

   If the QR code does not work, open the Shell Recharge app, search for the station by name or location, and start the session from the station page. You may need to select the specific connector or charger ID.

2. 2

   Check the charger ID number

   Every charger has an ID printed somewhere on the unit (usually near the QR code or on a label). Enter this ID manually in the Shell Recharge app if the QR scan fails.

3. 3

   Make sure the QR code belongs to Shell Recharge

   Many chargers have multiple QR codes from different roaming providers and the CPO itself. Make sure you are scanning the Shell Recharge QR code, not the CPO's own code. Scanning the wrong code opens the wrong app or website.

4. 4

   Try the RFID card or contactless payment instead

   QR code start is just one method. Tap your Shell Recharge RFID card or use contactless payment if the charger supports it.

5. 5

   Check your internet connection

   Starting a session via QR code requires the app to communicate with Shell Recharge's servers and the CPO's backend. If you have weak mobile signal (common at highway rest stops), the request may time out. Try switching between Wi-Fi and mobile data.

App showing wrong charger status

The Shell Recharge app shows a charger as available, occupied, or offline, but the actual status is different when you arrive.

Symptoms

• App shows 'Available' but the charger is out of order or has an error screen
• App shows 'Occupied' but no vehicle is connected
• Status has not updated for hours and seems stale
• App shows fewer chargers at a station than physically exist

How to Fix It

1. 1

   Understand that status data is delayed

   Shell Recharge gets charger status from the CPO's systems through the roaming connection. This data can lag by 5 to 15 minutes. A charger that just became available may still show as occupied in the app.

2. 2

   Try plugging in regardless of app status

   If you are already at the station and a charger looks physically available (no vehicle connected, no error on screen), try plugging in and starting a session. The real-time status at the charger overrides whatever the app shows.

3. 3

   Check the CPO's own app for more accurate status

   The CPO (the company that actually operates the charger) usually has more accurate real-time status than roaming aggregators like Shell Recharge. If accuracy matters, cross-check with the CPO's app or website.

4. 4

   Report the incorrect status

   Use the Shell Recharge app to report the charger issue. This helps improve status accuracy over time.

Billing discrepancy between Shell Recharge and the CPO

The amount billed by Shell Recharge does not match what you expected based on the energy delivered or the session duration. This can happen because of how roaming billing works.

Symptoms

• Billed for more kWh than your vehicle's dashboard shows
• Charged a session fee you did not expect
• Per-minute idle fee added even though you unplugged on time
• Double charge: both Shell Recharge and the CPO billed you

How to Fix It

1. 1

   Compare the Shell Recharge invoice with your vehicle's data

   Your vehicle's dashboard shows how much energy the battery received. The charger meters how much energy it delivered, which includes conversion losses. A 5 to 10% difference is normal.

2. 2

   Check for per-minute fees

   Some CPOs charge a per-minute fee (for time spent connected) on top of the per-kWh fee. This can be especially costly during slow AC charging sessions. Check the pricing breakdown in the Shell Recharge app.

3. 3

   Look for session or start fees

   Some stations add a fixed fee per session (for example, 0.35 EUR to 1.00 EUR). This appears in the Shell Recharge invoice as a separate line item.

4. 4

   Dispute the charge through the Shell Recharge app

   If the amount is clearly wrong (double billed, charged for a session that never started, or obviously excessive), contact Shell Recharge support through the app. Go to your charging history, select the session, and use the dispute or help option.

5. 5

   Keep your vehicle's charge data as evidence

   Take a photo of your vehicle's charging screen or dashboard showing the kWh received and the session duration. This is useful if you need to dispute a charge.