Tesla Model S Charging at Shell Recharge

Tesla Model S Charger Will Not Start a Session

You plugged in your Model S and nothing is happening. No green light on the charge port, no animation on the 17-inch touchscreen, just silence. Whether you are at a Supercharger, a third-party CCS2 station, or a home wallbox, there are a handful of common reasons the session will not begin.

Symptoms

• Charge port LED stays white or flashes red after plugging in the connector
• 17-inch touchscreen shows no charging animation or displays an error message
• Supercharger stall makes a click but does not begin delivering power
• CCS2 connector at a third-party station locks in but charging never starts
• Tesla app shows 'Not Charging' even though the cable is connected

What to Do

1. 1

   Check the charge port LED color

   Walk to the left rear of the car and look at the charge port light. White means ready but not connected. Blue means communicating. Green means charging. Red or amber means there is a fault. If it is white with the cable plugged in, remove and reseat the connector firmly.

2. 2

   Unplug and replug the connector

   Remove the connector completely, wait five seconds, then reinsert it until you hear the latch click. On CCS2 connectors, make sure both the top (AC pins) and bottom (DC pins) sections are seated properly.

3. 3

   Check for scheduled charging on the touchscreen

   On the 17-inch touchscreen, go to Controls, then Charging. If scheduled charging is active, you will see the planned start time. Tap to disable it or select 'Charge Now' to override the schedule.

4. 4

   Authorize the session at non-Tesla chargers

   At third-party CCS2 stations, check whether the charger requires you to start the session through an app, RFID card, or contactless payment. Plug & Charge works at supported stations, but many still require manual authorization.

5. 5

   Try a different stall or charger

   If you are at a Supercharger, move to a different stall. If you are at a third-party station, try the other connector. A faulted charger looks identical to a working one from the outside.

6. 6

   Restart the touchscreen

   Hold both scroll wheels on the steering wheel for about 10 seconds until the 17-inch touchscreen goes black and reboots. This resets the charging controller and fixes some communication glitches. The car stays on during the reboot.

Tesla Model S Payment Failed at Charging Station

You are plugged in and the charger is waiting for payment, or the Supercharger session will not start because of a billing issue. Payment problems are one of the most common reasons drivers get stuck at chargers, and the Model S has multiple ways to pay depending on where you are charging.

Symptoms

• Supercharger session will not start and the Tesla app shows a payment error
• Third-party CCS2 charger displays 'Authorization failed' after tapping your card
• RFID card is not recognized by the charger's reader
• Plug & Charge does not activate at a supported station
• Contactless bank card is rejected by the charger's payment terminal

What to Do

1. 1

   Check your Tesla account payment method

   Open the Tesla app on your phone. Go to Account, then Payment. Verify your credit card is current and has not expired. If the card was replaced, update the details. Supercharger sessions will not start without a valid payment method on file.

2. 2

   Try a different payment method at the charger

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having at least two payment methods gives you a backup when one does not work.

3. 3

   Scan the charger QR code for browser payment

   Most public chargers have a QR code on the unit. Scanning it with your phone opens the operator's payment page in your browser. You can usually pay with a credit card directly without downloading their app.

4. 4

   Check your banking app for blocked transactions

   Open your banking app and look for flagged or declined transactions. Some banks require you to approve the charge manually. Approve it and retry the payment at the charger.

5. 5

   Try Plug & Charge by replugging

   If the charger supports Plug & Charge, unplug the CCS2 connector from your Model S, wait a few seconds, and replug. Payment should authorize automatically through the cable. This only works if your Tesla account has Plug & Charge enabled and the charger supports ISO 15118.

6. 6

   Move to a Supercharger or a different station

   If you cannot resolve the payment issue, find a Tesla Supercharger using the nav on the 17-inch touchscreen. Supercharger billing is handled entirely through your Tesla account, bypassing third-party payment systems.

Tesla Model S Charging Slower Than Expected at Charger

You pulled into a Supercharger expecting 250 kW and the 17-inch touchscreen shows 80 kW. Or your home wallbox is crawling at 3 kW instead of 11 kW. The Model S has one of the fastest charging curves on the road, but reaching peak speed depends on battery temperature, state of charge, and a few settings you can check in under a minute.

Symptoms

• DC fast charging power well below 250 kW on the touchscreen despite a rated charger
• AC home charging stuck at 3-4 kW instead of the expected 11 kW on 3-phase
• Charging speed drops sharply after 40-50% on the touchscreen during DC fast charging
• Supercharger shows significantly lower kW than neighboring stalls
• Non-Tesla CCS2 charger delivers far less power than its rated maximum

What to Do

1. 1

   Check if the battery was preconditioned

   On the 17-inch touchscreen, tap the charging icon. If you see a snowflake icon or a message about conditioning, the battery was not warm enough when you arrived. Next time, navigate to the charger using Tesla nav at least 20-30 minutes before arrival so preconditioning kicks in automatically.

2. 2

   Check your current state of charge

   If you are above 50%, the slower speed is expected on the 95 kWh NCA pack. Peak power happens roughly between 5-30%. For the fastest charging stops on a road trip, arrive between 10-20%.

3. 3

   Move to an unpaired Supercharger stall

   Look at the stall numbers. If they are labeled in A/B pairs (3A/3B, 4A/4B), pick a stall where the paired stall is empty. At V3 or V4 Superchargers with the Magic Dock or the new V4 cable, this is not a concern.

4. 4

   Check the AC charge current limit on the touchscreen

   Go to Controls, then Charging on the touchscreen. Look for the charge current setting. Make sure it is set to the maximum amperage. This only affects AC charging at home or destination chargers, not Supercharging.

5. 5

   Try a different charger or stall

   If speeds remain low, the charger hardware may be degraded. Try another stall at the same location. On non-Tesla CCS2 stations, check the charger display for error codes or reduced power notices.

6. 6

   Check for a Tesla software update

   Go to Controls, then Software on the touchscreen. If an update is pending, install it. Tesla has adjusted charging curves through over-the-air updates in the past, sometimes improving peak speeds.

RFID card not recognized at the charger

You tap your Shell Recharge RFID card on the charger's reader but it does not respond, beeps an error, or shows 'Card not recognized.'

Symptoms

• Charger beeps but displays 'Unknown card' or 'Authorization failed'
• No response at all when tapping the card
• Card works at some stations but not others
• Card worked yesterday at the same charger but does not work today

How to Fix It

1. 1

   Hold the card still on the reader for 3 to 5 seconds

   RFID readers at some chargers are slow. Do not tap and remove quickly. Hold the card flat against the reader and wait for a confirmation beep or screen change.

2. 2

   Check that your RFID card is activated

   New Shell Recharge RFID cards must be activated in the Shell Recharge app before first use. Go to the app, find the RFID section, and make sure the card status shows active.

3. 3

   Try starting the session through the app instead

   Open the Shell Recharge app, find the station, select the charger, and start the session digitally. This bypasses the RFID reader entirely and uses the roaming connection.

4. 4

   Check if the CPO supports Shell Recharge roaming

   Not every charger that appears in the Shell Recharge app accepts the Shell Recharge RFID card. Some chargers only accept app-based roaming. The station details in the app usually indicate which payment methods are supported.

5. 5

   Clean the card and try again

   Dirt, scratches, or a phone case between the card and reader can block the RFID signal. Remove the card from any holder, wipe it, and try again on the reader's sweet spot (often marked with a contactless symbol).

Roaming vs direct pricing confusion

The price you pay through Shell Recharge is different from the price shown on the charger's screen. This is because Shell Recharge adds a roaming markup on top of the CPO's base rate.

Symptoms

• Charger screen shows 0.39 EUR/kWh but Shell Recharge bills 0.55 EUR/kWh
• Invoice includes fees not displayed at the charger (session fee, per-minute fee)
• Same station is cheaper when using the CPO's own app
• Pricing in the Shell Recharge app does not match the final invoice

How to Fix It

1. 1

   Check the Shell Recharge app for the roaming price before starting

   Before you tap your card or start a session, open the Shell Recharge app and select the station. The app shows the Shell Recharge price, which includes any roaming fee. This is the price you will actually pay.

2. 2

   Understand the pricing structure

   Shell Recharge typically charges a per-kWh rate plus sometimes a session start fee or per-minute fee. The charger screen shows the CPO's direct price, not the roaming price. These are two different rates for two different billing relationships.

3. 3

   Consider using the CPO's own app for lower rates

   If you charge at the same network regularly (for example, Allego, Fastned, or EnBW), their own app usually offers a lower price than roaming through Shell Recharge. The trade-off is managing multiple apps.

4. 4

   Download your invoice from the Shell Recharge app

   Go to your charging history in the Shell Recharge app. Each session has a detailed breakdown showing energy delivered, per-kWh rate, session fees, and total cost. Compare this with what you expected.

Session not starting via QR code

You scan the QR code on the charger to start a session through the Shell Recharge app, but nothing happens or you get an error.

Symptoms

• QR code opens the Shell Recharge app but shows 'Station not found'
• QR code opens a web page instead of the app
• App shows 'Unable to start session' after scanning
• QR code is faded, damaged, or partially covered by a sticker

How to Fix It

1. 1

   Search for the station manually in the app

   If the QR code does not work, open the Shell Recharge app, search for the station by name or location, and start the session from the station page. You may need to select the specific connector or charger ID.

2. 2

   Check the charger ID number

   Every charger has an ID printed somewhere on the unit (usually near the QR code or on a label). Enter this ID manually in the Shell Recharge app if the QR scan fails.

3. 3

   Make sure the QR code belongs to Shell Recharge

   Many chargers have multiple QR codes from different roaming providers and the CPO itself. Make sure you are scanning the Shell Recharge QR code, not the CPO's own code. Scanning the wrong code opens the wrong app or website.

4. 4

   Try the RFID card or contactless payment instead

   QR code start is just one method. Tap your Shell Recharge RFID card or use contactless payment if the charger supports it.

5. 5

   Check your internet connection

   Starting a session via QR code requires the app to communicate with Shell Recharge's servers and the CPO's backend. If you have weak mobile signal (common at highway rest stops), the request may time out. Try switching between Wi-Fi and mobile data.

App showing wrong charger status

The Shell Recharge app shows a charger as available, occupied, or offline, but the actual status is different when you arrive.

Symptoms

• App shows 'Available' but the charger is out of order or has an error screen
• App shows 'Occupied' but no vehicle is connected
• Status has not updated for hours and seems stale
• App shows fewer chargers at a station than physically exist

How to Fix It

1. 1

   Understand that status data is delayed

   Shell Recharge gets charger status from the CPO's systems through the roaming connection. This data can lag by 5 to 15 minutes. A charger that just became available may still show as occupied in the app.

2. 2

   Try plugging in regardless of app status

   If you are already at the station and a charger looks physically available (no vehicle connected, no error on screen), try plugging in and starting a session. The real-time status at the charger overrides whatever the app shows.

3. 3

   Check the CPO's own app for more accurate status

   The CPO (the company that actually operates the charger) usually has more accurate real-time status than roaming aggregators like Shell Recharge. If accuracy matters, cross-check with the CPO's app or website.

4. 4

   Report the incorrect status

   Use the Shell Recharge app to report the charger issue. This helps improve status accuracy over time.

Billing discrepancy between Shell Recharge and the CPO

The amount billed by Shell Recharge does not match what you expected based on the energy delivered or the session duration. This can happen because of how roaming billing works.

Symptoms

• Billed for more kWh than your vehicle's dashboard shows
• Charged a session fee you did not expect
• Per-minute idle fee added even though you unplugged on time
• Double charge: both Shell Recharge and the CPO billed you

How to Fix It

1. 1

   Compare the Shell Recharge invoice with your vehicle's data

   Your vehicle's dashboard shows how much energy the battery received. The charger meters how much energy it delivered, which includes conversion losses. A 5 to 10% difference is normal.

2. 2

   Check for per-minute fees

   Some CPOs charge a per-minute fee (for time spent connected) on top of the per-kWh fee. This can be especially costly during slow AC charging sessions. Check the pricing breakdown in the Shell Recharge app.

3. 3

   Look for session or start fees

   Some stations add a fixed fee per session (for example, 0.35 EUR to 1.00 EUR). This appears in the Shell Recharge invoice as a separate line item.

4. 4

   Dispute the charge through the Shell Recharge app

   If the amount is clearly wrong (double billed, charged for a session that never started, or obviously excessive), contact Shell Recharge support through the app. Go to your charging history, select the session, and use the dispute or help option.

5. 5

   Keep your vehicle's charge data as evidence

   Take a photo of your vehicle's charging screen or dashboard showing the kWh received and the session duration. This is useful if you need to dispute a charge.