Hyundai Kona Electric Charging at BP Pulse

Hyundai Kona Electric Charger Won't Start? Fix Guide

You have plugged the cable into your Kona Electric, but nothing is happening. No charging indicator, no progress on the screen. The Kona Electric's charge port is in the front, under a flap on the nose of the car. This unusual location sometimes causes cable reach problems. But the issue is usually authentication, a car setting, or the charger itself.

Symptoms

• CCS2 or Type 2 cable plugged in but no charging indicator on the dashboard
• Charge port LED stays off or flashes an error pattern
• Charger screen shows an error or stays on the start screen
• Bluelink app shows the car is not connected to a charger
• Charging begins briefly then stops within seconds

What to Do

1. 1

   Open the front charge port and check the cable

   The charge port is on the front of the car, under a flap. Press the flap to open it. If it is stiff, press more firmly. Insert the CCS2 connector straight in until you hear a click. The LED should light up.

2. 2

   Make sure you are parked nose-in

   Unlike most EVs with rear charge ports, the Kona Electric needs to face the charger. If you backed in, the cable probably will not reach. Pull out and park nose-first.

3. 3

   Authenticate with the charger

   Tap your RFID card, use the charging network's app, or try contactless payment. The Kona Electric does not have Plug & Charge, so you will always need to authenticate manually at DC fast chargers.

4. 4

   Check for a charging schedule

   On the infotainment screen, go to EV settings, then Scheduled Charging. Disable any active schedule or tap 'Charge Now' to override it.

5. 5

   Unplug, wait 30 seconds, and try again

   Remove the cable, wait 30 seconds, reconnect, and re-authenticate. This resets both the car and charger communication.

6. 6

   Try a different charger

   If the session still will not start, the charger is likely faulty. Try another stall or station. Report the broken charger through the network's app.

Hyundai Kona Electric Charger Payment Failed at Station

You are at a public charger with your Kona Electric, the cable is in, but payment will not go through. The charger shows an error, the app is not cooperating, or your RFID card gets no response. The Kona Electric does not support Plug & Charge, so you always need to authenticate manually. Here is how to work through payment problems.

Symptoms

• Charger screen shows 'payment failed' or 'authorization error'
• RFID card tapped but the charger does not respond
• Charging network app shows an error or hangs during payment
• Contactless card payment declined at the charger terminal
• QR code on the charger leads to a page that will not load

What to Do

1. 1

   Try a different payment method

   If RFID failed, open the charging app. If the app failed, try contactless with a credit or debit card. Having multiple options is the fastest way past payment issues.

2. 2

   Check your charging app account

   Open the app and verify your payment method is valid. Look for expired cards, low prepaid balances, or account restrictions. Update your card details if needed.

3. 3

   Scan the QR code on the charger

   Many chargers have a QR code that opens a web-based payment page. This lets you pay without an account or app. Scan it with your phone camera.

4. 4

   Try a different stall at the same station

   If one charger's payment terminal is broken, the next one over may work fine. Walk to the next stall and try the same payment method.

5. 5

   Try a different charging station

   If all stalls at this location have payment issues, the entire station may have a connectivity problem. Head to a nearby alternative station.

Hyundai Kona Electric Charging Slower Than Expected

The Kona Electric supports up to 100 kW DC fast charging, which is solid but noticeably slower than the 233 kW that 800V Hyundai models can reach. If your Kona is pulling 30 kW at a charger rated for much more, something is off. In most cases, slow charging comes down to battery temperature, state of charge, or the charger not delivering its full rated output.

Symptoms

• DC fast charging speed well below the 100 kW maximum
• AC charging stuck at 3-4 kW instead of 11 kW on a 3-phase connection
• Charging speed drops significantly above 60% state of charge
• Session starts at low power and never ramps up to full speed
• Charger screen shows a lower power output than the unit's rated capacity

What to Do

1. 1

   Check the battery temperature

   Look at the charging information on the 12.3-inch touchscreen. If the battery is cold, use the preconditioning feature in the Bluelink app before arriving at the charger. Driving for 15-20 minutes also warms the battery naturally.

2. 2

   Check your state of charge

   If you are above 70%, the slowdown is expected on the Kona Electric. For road trip charging, plan to arrive between 10-20% and unplug at 80% for the best time-to-range ratio.

3. 3

   Check the charger's rated output

   Look at the charger's specs on its screen, on the unit label, or in the charging network's app. If it is a 50 kW charger, the Kona Electric is getting what the charger can deliver. Find a higher-powered CCS2 charger for faster sessions.

4. 4

   Check scheduled charging and charge limits

   On the infotainment screen or in the Bluelink app, make sure scheduled charging is not delaying or limiting the session. Check that the charge current limit is set to maximum.

5. 5

   Check if the charger is sharing power

   Look at the charger cabinet. If two cables come from the same unit and someone is charging on the other cable, you may be splitting power. Move to an unoccupied charger if available.

6. 6

   Try a different charger or station

   If speed is still low after checking everything, the charger may be underperforming. Try another stall or a different station entirely.

Contactless reader not responding

You tap your bank card or phone and nothing happens. The screen does not acknowledge the tap at all, or it briefly flashes and returns to the start screen.

Symptoms

• No beep or screen change after tapping your card
• Screen flashes 'Card read error' then resets
• Apple Pay or Google Pay shows 'Done' on your phone but the charger does not start
• Reader works on one unit but not the adjacent one

How to Fix It

1. 1

   Try a physical bank card instead of your phone

   Contactless phone payments sometimes fail on BP Pulse readers even when a physical card works fine. Hold the card flat against the reader for 2-3 seconds.

2. 2

   Check for a second tap point

   Some BP Pulse units have the contactless reader on the side panel rather than below the screen. Look for a card symbol printed on the housing.

3. 3

   Clean the reader surface

   Wipe dirt, rain, or condensation off the contactless reader area with your sleeve. Moisture on the sensor can prevent a clean read.

4. 4

   Start the session via the BP Pulse app instead

   Open the app, find the charger on the map, select the connector, and tap 'Start Charging.' This bypasses the physical reader entirely.

5. 5

   Try the other connector or an adjacent unit

   If the charger has two connectors, the other side may have a working reader. Or walk to the next unit. Contactless reader failures are often limited to one specific unit.

BP Pulse app crashing on Android

The app closes unexpectedly when you try to start a session, view the map, or enter payment details. This is more common on older Android versions and after recent app updates.

Symptoms

• App closes immediately after opening
• App freezes on the map screen then crashes
• Crash when tapping 'Start Charging' after selecting a connector
• 'App keeps stopping' notification from Android

How to Fix It

1. 1

   Force close and reopen the app

   Go to Android Settings, then Apps, then BP Pulse. Tap 'Force Stop,' wait a few seconds, then open the app again.

2. 2

   Clear the app cache

   In Settings, go to Apps, then BP Pulse, then Storage, then 'Clear Cache.' This removes temporary data without deleting your account. You will not need to log in again.

3. 3

   Check for an app update

   Open the Google Play Store, search for BP Pulse, and tap 'Update' if available. Crashes often follow a buggy release that gets patched within days.

4. 4

   Use contactless payment as a backup

   If the app will not cooperate, tap your bank card on the charger's contactless reader to start a session without the app.

5. 5

   Reinstall the app if crashes persist

   Uninstall BP Pulse, restart your phone, then reinstall from the Play Store. You will need to log in again, so make sure you know your BP Pulse account email.

Charger shows 'Out of Service' with no visible damage

The screen displays 'Out of Service' or 'Unavailable,' but the charger looks perfectly fine. No broken cables, no barrier tape, no obvious reason it should be offline.

Symptoms

• Screen stuck on 'Out of Service' message
• Charger appears available in the app but shows error on arrival
• Status light is red or off entirely
• Other chargers at the same location work fine

How to Fix It

1. 1

   Check the BP Pulse app for real-time status

   Open the app and look at this specific charger. If it shows as unavailable there too, the network has flagged it remotely. A maintenance team likely already knows.

2. 2

   Look for a reset button or power switch

   Some older BP Pulse units (especially former Chargemaster ones) have a small reset button behind a panel or near the base. Pressing it can sometimes clear a stuck error state.

3. 3

   Report it in the app

   Use the 'Report a problem' option on the charger's detail page in the BP Pulse app. This helps BP Pulse prioritize repairs and updates the status for other drivers.

4. 4

   Move to another charger

   An 'Out of Service' state usually means a backend fault, a communication issue with the network, or a pending software update. You cannot fix these yourself. Use another unit or location.

Charging session drops after 5-10 minutes

Charging starts normally, but the session ends on its own after a few minutes. Your car shows it is no longer receiving power, and the charger returns to the welcome screen.

Symptoms

• Car dashboard shows charging stopped unexpectedly
• Charger screen returns to 'Plug in to start' after a few minutes
• You receive a session-ended notification in the app with a very short session
• This happens repeatedly at the same charger

How to Fix It

1. 1

   Check the connector is fully seated

   Unplug the cable, inspect the connector pins for dirt or debris, and plug it back in firmly until you hear a click. A loose connection can cause the charger to drop the session.

2. 2

   Check your car's charge limit

   If your car's charge limit is set very close to the current battery level, some vehicles will stop charging almost immediately. Set the limit to 80% or higher and try again.

3. 3

   Try the other connector type

   If the charger offers both CCS2 and CHAdeMO and your car supports CCS2, make sure you are using CCS2. Using the wrong connector obviously will not fit, but a worn CCS2 connector on one side may work better on the other unit.

4. 4

   Start a new session at a different unit

   Repeated drops at the same charger point to a hardware fault on that unit. Move to another charger and try again.

5. 5

   Report the faulty unit

   Note the charger ID (printed on the unit) and report it via the BP Pulse app or call the BP Pulse support number shown on the charger. This helps get the unit serviced.

Subscription vs pay-as-you-go pricing confusion

BP Pulse offers a subscription plan with lower per-kWh rates and a pay-as-you-go option with higher rates. It is not always clear which pricing you are on, or whether the subscription is worth it for your usage.

Symptoms

• Charged a higher rate than expected on your receipt
• Unsure whether your subscription is active
• Signed up for subscription but still seeing non-member prices
• Cannot figure out how to switch between plans

How to Fix It

1. 1

   Check your plan status in the app

   Open the BP Pulse app, go to your account settings, and look for your subscription status. If it says 'Active,' you should be getting the lower rate automatically.

2. 2

   Make sure you are starting sessions through the app

   Subscription pricing only applies when you start the session via the BP Pulse app or RFID card linked to your account. Tapping a contactless bank card will charge you the standard pay-as-you-go rate.

3. 3

   Review your charging history for rate discrepancies

   In the app, go to Charging History and check the per-kWh rate on recent sessions. Compare this to the subscription rate listed on the BP Pulse pricing page.

4. 4

   Cancel or change your plan if needed

   You can manage your subscription in the app under Account, then Subscription. If you charge infrequently, pay-as-you-go may actually cost less overall despite the higher per-kWh rate.