Hyundai Kona Electric Charging at Recharge

Hyundai Kona Electric Charger Won't Start? Fix Guide

You have plugged the cable into your Kona Electric, but nothing is happening. No charging indicator, no progress on the screen. The Kona Electric's charge port is in the front, under a flap on the nose of the car. This unusual location sometimes causes cable reach problems. But the issue is usually authentication, a car setting, or the charger itself.

Symptoms

• CCS2 or Type 2 cable plugged in but no charging indicator on the dashboard
• Charge port LED stays off or flashes an error pattern
• Charger screen shows an error or stays on the start screen
• Bluelink app shows the car is not connected to a charger
• Charging begins briefly then stops within seconds

What to Do

1. 1

   Open the front charge port and check the cable

   The charge port is on the front of the car, under a flap. Press the flap to open it. If it is stiff, press more firmly. Insert the CCS2 connector straight in until you hear a click. The LED should light up.

2. 2

   Make sure you are parked nose-in

   Unlike most EVs with rear charge ports, the Kona Electric needs to face the charger. If you backed in, the cable probably will not reach. Pull out and park nose-first.

3. 3

   Authenticate with the charger

   Tap your RFID card, use the charging network's app, or try contactless payment. The Kona Electric does not have Plug & Charge, so you will always need to authenticate manually at DC fast chargers.

4. 4

   Check for a charging schedule

   On the infotainment screen, go to EV settings, then Scheduled Charging. Disable any active schedule or tap 'Charge Now' to override it.

5. 5

   Unplug, wait 30 seconds, and try again

   Remove the cable, wait 30 seconds, reconnect, and re-authenticate. This resets both the car and charger communication.

6. 6

   Try a different charger

   If the session still will not start, the charger is likely faulty. Try another stall or station. Report the broken charger through the network's app.

Hyundai Kona Electric Charger Payment Failed at Station

You are at a public charger with your Kona Electric, the cable is in, but payment will not go through. The charger shows an error, the app is not cooperating, or your RFID card gets no response. The Kona Electric does not support Plug & Charge, so you always need to authenticate manually. Here is how to work through payment problems.

Symptoms

• Charger screen shows 'payment failed' or 'authorization error'
• RFID card tapped but the charger does not respond
• Charging network app shows an error or hangs during payment
• Contactless card payment declined at the charger terminal
• QR code on the charger leads to a page that will not load

What to Do

1. 1

   Try a different payment method

   If RFID failed, open the charging app. If the app failed, try contactless with a credit or debit card. Having multiple options is the fastest way past payment issues.

2. 2

   Check your charging app account

   Open the app and verify your payment method is valid. Look for expired cards, low prepaid balances, or account restrictions. Update your card details if needed.

3. 3

   Scan the QR code on the charger

   Many chargers have a QR code that opens a web-based payment page. This lets you pay without an account or app. Scan it with your phone camera.

4. 4

   Try a different stall at the same station

   If one charger's payment terminal is broken, the next one over may work fine. Walk to the next stall and try the same payment method.

5. 5

   Try a different charging station

   If all stalls at this location have payment issues, the entire station may have a connectivity problem. Head to a nearby alternative station.

Hyundai Kona Electric Charging Slower Than Expected

The Kona Electric supports up to 100 kW DC fast charging, which is solid but noticeably slower than the 233 kW that 800V Hyundai models can reach. If your Kona is pulling 30 kW at a charger rated for much more, something is off. In most cases, slow charging comes down to battery temperature, state of charge, or the charger not delivering its full rated output.

Symptoms

• DC fast charging speed well below the 100 kW maximum
• AC charging stuck at 3-4 kW instead of 11 kW on a 3-phase connection
• Charging speed drops significantly above 60% state of charge
• Session starts at low power and never ramps up to full speed
• Charger screen shows a lower power output than the unit's rated capacity

What to Do

1. 1

   Check the battery temperature

   Look at the charging information on the 12.3-inch touchscreen. If the battery is cold, use the preconditioning feature in the Bluelink app before arriving at the charger. Driving for 15-20 minutes also warms the battery naturally.

2. 2

   Check your state of charge

   If you are above 70%, the slowdown is expected on the Kona Electric. For road trip charging, plan to arrive between 10-20% and unplug at 80% for the best time-to-range ratio.

3. 3

   Check the charger's rated output

   Look at the charger's specs on its screen, on the unit label, or in the charging network's app. If it is a 50 kW charger, the Kona Electric is getting what the charger can deliver. Find a higher-powered CCS2 charger for faster sessions.

4. 4

   Check scheduled charging and charge limits

   On the infotainment screen or in the Bluelink app, make sure scheduled charging is not delaying or limiting the session. Check that the charge current limit is set to maximum.

5. 5

   Check if the charger is sharing power

   Look at the charger cabinet. If two cables come from the same unit and someone is charging on the other cable, you may be splitting power. Move to an unoccupied charger if available.

6. 6

   Try a different charger or station

   If speed is still low after checking everything, the charger may be underperforming. Try another stall or a different station entirely.

Charger stuck in "preparing" state

You authenticated successfully, the charger says "preparing," but it never starts delivering power. This is one of the most reported issues on Recharge stations, especially at older units.

Symptoms

• Charger screen shows "Preparing" or "Initializing" for more than two minutes
• Your car's charging indicator does not activate
• The Recharge app shows the session as active but 0 kW delivered
• The charger fan spins up but no power flows

How to Fix It

1. 1

   Wait up to three minutes

   Some Recharge units, particularly the 300kW stations, take longer to complete the power handshake with your car. Give it a full three minutes before taking action.

2. 2

   Unplug and reconnect

   Remove the CCS2 connector, wait 15 seconds, then plug it back in firmly. This resets the communication between your car and the charger.

3. 3

   Stop the session in the Recharge app and start a new one

   Open the Recharge app, tap Stop on the active session, wait for it to fully end, then start a new session on the same charger. This clears any stuck state on the backend.

4. 4

   Try the other connector on the same unit

   Many Recharge stations have two CCS2 connectors. If one is stuck, the other connector on the same unit often works fine.

5. 5

   Use a different authentication method

   If you started with the app, try your RFID card instead, or vice versa. Sometimes the issue is with the authentication path, not the charger hardware.

Old Fortum branding causes app scan failure

Recharge was originally part of Fortum's charging operations before being spun off as a separate company. Some older stations still display Fortum logos and QR codes. Scanning an old Fortum QR code with the Recharge app may not work, or it may redirect to a dead Fortum page.

Symptoms

• QR code on the charger opens a Fortum website or shows an error
• Recharge app says "Charger not found" after scanning
• Station ID on the physical unit does not match what the Recharge app expects
• The charger has Fortum branding but is listed as Recharge in third-party apps

How to Fix It

1. 1

   Ignore the QR code and search by station name in the Recharge app

   Open the Recharge app, use the map or search to find the station by location. The charger will appear under its Recharge name even if the physical unit still says Fortum.

2. 2

   Enter the charger ID manually

   Look for a numeric ID on the charger, often printed on a sticker near the connector. In the Recharge app, tap "Enter ID" and type it in directly.

3. 3

   Use RFID or contactless payment instead of the app

   Tap your Recharge RFID card or a contactless bank card on the reader. This bypasses the app entirely and works regardless of the branding on the charger.

4. 4

   Check if contactless is available on this unit

   Not all Recharge stations support contactless bank card payment. Look for a card reader terminal on the charger. If there is no terminal, you will need the app or an RFID card.

RFID card from old Fortum account not recognized

If you had a Fortum Charge & Drive account and RFID card, it may not work automatically on the Recharge network. Some cards were migrated, others were not.

Symptoms

• Tapping your old Fortum RFID card shows "Card not recognized" on the charger
• The charger beeps but does not start a session
• Your Fortum card works on some stations but not others

How to Fix It

1. 1

   Log in to the Recharge app and check your RFID cards

   Open the Recharge app, go to your account settings, and look under RFID cards. If your old Fortum card is not listed, it was not migrated automatically.

2. 2

   Re-register your RFID card

   In the Recharge app, tap "Add RFID card" and follow the steps. You will need the card number printed on the back of your RFID card.

3. 3

   Use the app to start the session while you wait for RFID activation

   RFID card registration can take up to 24 hours to propagate across all stations. Use the app to authenticate in the meantime.

4. 4

   Order a new Recharge RFID card if re-registration fails

   Some older Fortum cards use a chip format that is not compatible. You can order a new Recharge RFID card through the app or website.

Contactless payment not accepted

You are trying to tap your bank card or phone to pay, but the charger does not respond or shows an error. Contactless payment availability varies across Recharge stations.

Symptoms

• No card reader terminal visible on the charger
• Card reader shows "Payment failed" or does not respond to taps
• Apple Pay or Google Pay not recognized
• The charger prompts for an RFID card but you only have a bank card

How to Fix It

1. 1

   Check if this station supports contactless payment

   Look for a separate payment terminal with a contactless symbol. Not all Recharge stations have been upgraded. The Recharge app shows payment options for each station on the station detail page.

2. 2

   Try removing and re-holding your card

   Hold your card flat against the reader for at least three seconds. Some terminals need a longer hold than you might expect. Remove the card fully, then try again.

3. 3

   Fall back to the Recharge app

   If contactless is not working, open the Recharge app and start the session from there. You need a payment method saved in the app.

4. 4

   Try a different card

   Some Visa Electron and certain prepaid cards are not accepted by the payment terminals. A standard Visa or Mastercard debit or credit card usually works.

Charging speed much lower than expected

The station is rated for 300kW, but your car is only pulling 50kW or less. While your car's battery management limits the maximum speed, Recharge stations can also throttle power.

Symptoms

• Charger display shows far less power than the station's rated capacity
• Charging speed drops suddenly mid-session
• Other cars at the same station are also charging slowly
• The Recharge app shows the session but at low power

How to Fix It

1. 1

   Check how many other cars are charging at the same station

   Recharge stations with multiple connectors often share a power cabinet. If two or three cars are charging simultaneously, the available power per car drops. This is normal and not a fault.

2. 2

   Check your battery level

   DC fast charging slows significantly above 80% on most EVs. If your battery is above 70-80%, the slower speed is your car protecting the battery, not a problem with the Recharge station.

3. 3

   Check the temperature

   In cold weather, your car may limit charging speed until the battery warms up. This can take 10-15 minutes of charging before speeds increase. Some cars precondition the battery if you set the charger as a destination in navigation.

4. 4

   Try a different connector at the station

   Individual connectors can have faults that limit power output. If another connector is free, unplug and try it.

5. 5

   Report the issue in the Recharge app

   If the speed is unusually low and none of the above apply, report it through the Recharge app. Tap the active session and look for a "Report issue" option. This helps Recharge identify hardware problems.