BP Pulse Charger Not Working?

Symptoms

• No beep or screen change after tapping your card
• Screen flashes 'Card read error' then resets
• Apple Pay or Google Pay shows 'Done' on your phone but the charger does not start
• Reader works on one unit but not the adjacent one

How to Fix It

1. 1

   Try a physical bank card instead of your phone

   Contactless phone payments sometimes fail on BP Pulse readers even when a physical card works fine. Hold the card flat against the reader for 2-3 seconds.

2. 2

   Check for a second tap point

   Some BP Pulse units have the contactless reader on the side panel rather than below the screen. Look for a card symbol printed on the housing.

3. 3

   Clean the reader surface

   Wipe dirt, rain, or condensation off the contactless reader area with your sleeve. Moisture on the sensor can prevent a clean read.

4. 4

   Start the session via the BP Pulse app instead

   Open the app, find the charger on the map, select the connector, and tap 'Start Charging.' This bypasses the physical reader entirely.

5. 5

   Try the other connector or an adjacent unit

   If the charger has two connectors, the other side may have a working reader. Or walk to the next unit. Contactless reader failures are often limited to one specific unit.

Symptoms

• App closes immediately after opening
• App freezes on the map screen then crashes
• Crash when tapping 'Start Charging' after selecting a connector
• 'App keeps stopping' notification from Android

How to Fix It

1. 1

   Force close and reopen the app

   Go to Android Settings, then Apps, then BP Pulse. Tap 'Force Stop,' wait a few seconds, then open the app again.

2. 2

   Clear the app cache

   In Settings, go to Apps, then BP Pulse, then Storage, then 'Clear Cache.' This removes temporary data without deleting your account. You will not need to log in again.

3. 3

   Check for an app update

   Open the Google Play Store, search for BP Pulse, and tap 'Update' if available. Crashes often follow a buggy release that gets patched within days.

4. 4

   Use contactless payment as a backup

   If the app will not cooperate, tap your bank card on the charger's contactless reader to start a session without the app.

5. 5

   Reinstall the app if crashes persist

   Uninstall BP Pulse, restart your phone, then reinstall from the Play Store. You will need to log in again, so make sure you know your BP Pulse account email.

Symptoms

• Screen stuck on 'Out of Service' message
• Charger appears available in the app but shows error on arrival
• Status light is red or off entirely
• Other chargers at the same location work fine

How to Fix It

1. 1

   Check the BP Pulse app for real-time status

   Open the app and look at this specific charger. If it shows as unavailable there too, the network has flagged it remotely. A maintenance team likely already knows.

2. 2

   Look for a reset button or power switch

   Some older BP Pulse units (especially former Chargemaster ones) have a small reset button behind a panel or near the base. Pressing it can sometimes clear a stuck error state.

3. 3

   Report it in the app

   Use the 'Report a problem' option on the charger's detail page in the BP Pulse app. This helps BP Pulse prioritize repairs and updates the status for other drivers.

4. 4

   Move to another charger

   An 'Out of Service' state usually means a backend fault, a communication issue with the network, or a pending software update. You cannot fix these yourself. Use another unit or location.

Symptoms

• Car dashboard shows charging stopped unexpectedly
• Charger screen returns to 'Plug in to start' after a few minutes
• You receive a session-ended notification in the app with a very short session
• This happens repeatedly at the same charger

How to Fix It

1. 1

   Check the connector is fully seated

   Unplug the cable, inspect the connector pins for dirt or debris, and plug it back in firmly until you hear a click. A loose connection can cause the charger to drop the session.

2. 2

   Check your car's charge limit

   If your car's charge limit is set very close to the current battery level, some vehicles will stop charging almost immediately. Set the limit to 80% or higher and try again.

3. 3

   Try the other connector type

   If the charger offers both CCS2 and CHAdeMO and your car supports CCS2, make sure you are using CCS2. Using the wrong connector obviously will not fit, but a worn CCS2 connector on one side may work better on the other unit.

4. 4

   Start a new session at a different unit

   Repeated drops at the same charger point to a hardware fault on that unit. Move to another charger and try again.

5. 5

   Report the faulty unit

   Note the charger ID (printed on the unit) and report it via the BP Pulse app or call BP Pulse support at 0330 016 5126 (UK). This helps get the unit serviced.

Symptoms

• Charged a higher rate than expected on your receipt
• Unsure whether your subscription is active
• Signed up for subscription but still seeing non-member prices
• Cannot figure out how to switch between plans

How to Fix It

1. 1

   Check your plan status in the app

   Open the BP Pulse app, go to your account settings, and look for your subscription status. If it says 'Active,' you should be getting the lower rate automatically.

2. 2

   Make sure you are starting sessions through the app

   Subscription pricing only applies when you start the session via the BP Pulse app or RFID card linked to your account. Tapping a contactless bank card will charge you the standard pay-as-you-go rate.

3. 3

   Review your charging history for rate discrepancies

   In the app, go to Charging History and check the per-kWh rate on recent sessions. Compare this to the subscription rate listed on the BP Pulse pricing page.

4. 4

   Cancel or change your plan if needed

   You can manage your subscription in the app under Account, then Subscription. If you charge infrequently, pay-as-you-go may actually cost less overall despite the higher per-kWh rate.