Volvo EX90 Charging at GreenWay

Volvo EX90 Plugged In but the Charger Will Not Start

You connected the cable to your Volvo EX90 and nothing happens. No charging indicator on the screen, no confirmation from the charger. The EX90 supports Plug & Charge and multiple authentication methods, but when none of them work, you need to troubleshoot step by step.

Symptoms

• Charger displays an error after plugging in the EX90
• Charge port LED does not light up or stays amber
• 14.5-inch center screen shows no active charging session
• Charger screen says 'waiting for vehicle' or shows a timeout
• CCS connector plugs in but does not lock into the charge port

What to Do

1. 1

   Authenticate with the charger

   Check the charger's screen for payment instructions. Tap your RFID card, open the charging network's app, or use contactless payment. Plug & Charge should activate automatically on supported networks, but if it does not, use manual authentication.

2. 2

   Check the charge port on the left rear

   Open the charge port door fully. Check for ice, snow, or debris. In winter, gently clear any obstructions. Make sure the port cover is not partially blocking the connector.

3. 3

   Seat the connector firmly

   Push the CCS2 connector straight into the port until it clicks and locks. If it will not lock, pull it out and try again. Check that the connector pins are clean and undamaged.

4. 4

   Turn off scheduled charging

   On the center screen, go to Settings, then Charging. If a charging schedule is active, disable it or switch to 'charge immediately.' This is a common reason charging will not start at public chargers.

5. 5

   Restart the charging process

   Unplug the connector, lock and unlock the car using the Volvo Cars app or key, wait 15 seconds, then plug in again. This resets the charging communication.

Volvo EX90 Charger Payment Failed or Card Declined

You are at a public charger with your Volvo EX90 and the payment will not go through. The card reader rejects your card, the app throws an error, or Plug & Charge just does not activate. Payment issues at public chargers are one of the most common frustrations, and they have nothing to do with your car's charging system.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Plug & Charge does not activate when you connect the cable
• Charging app shows a payment error or insufficient balance
• Contactless payment terminal does not respond
• You cannot find any way to pay at the charger

What to Do

1. 1

   Check Plug & Charge status in the Volvo Cars app

   Open the Volvo Cars app and verify that Plug & Charge is enabled with a valid payment method. If the network supports it, try unplugging and reconnecting. If not, proceed to manual payment.

2. 2

   Try a different payment method

   Use a different credit or debit card, your phone's mobile wallet, or the charging network's app. Having multiple options avoids being stuck when one fails.

3. 3

   Check for pre-authorization holds

   Open your banking app and look for pending charges from the charging network. Multiple failed attempts may have placed several holds, reducing your available balance. Contact your bank if needed.

4. 4

   Use the charging network's app instead

   Find the network name on the charger. Download their app, create an account, add a payment method, and start the session through the app. This bypasses the physical payment terminal entirely.

5. 5

   Tap your RFID charging card

   If you carry an RFID card from a charging provider or roaming service, tap it on the charger's card reader. RFID cards are often more reliable than apps or contactless terminals.

Volvo EX90 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX90 expecting 250 kW and the 14.5-inch screen shows 60 kW. Or your wallbox is only delivering 3 kW instead of 11 kW. The EX90 has one of the fastest charging speeds in its class, but reaching that peak depends on battery temperature, state of charge, and the charger itself.

Symptoms

• DC fast charging speed well below the 250 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 40-50%
• Center screen shows lower power than the charger's rated output
• Charging session starts strong but slows down within 10 minutes

What to Do

1. 1

   Set the charger as your navigation destination

   Use Google Maps on the 14.5-inch center screen to navigate to the charging station. The EX90 will start preconditioning the battery automatically during the drive, preparing it for peak charging speed.

2. 2

   Check the charger's rated power

   Before plugging in, check the charger's label or the app for its maximum output. If the charger is rated at 150 kW, your EX90 cannot charge faster than 150 kW regardless of its 250 kW capability.

3. 3

   Check your state of charge

   For the fastest charging, arrive between 10-20%. The EX90's peak speeds are available at lower states of charge. Above 80%, charging will slow significantly.

4. 4

   Verify the charger is not sharing power

   Many chargers split power between two connectors. If someone is using the adjacent stall, both cars get reduced speeds. Move to a charger with both stalls free.

5. 5

   Check AC charge current settings

   If charging slowly on AC, check the EX90's settings to ensure the charge current limiter is set to maximum. Also verify your wallbox is properly wired for 3-phase.

6. 6

   Try a higher-powered charger

   To take advantage of the EX90's 250 kW capability, look for chargers rated at 300 kW or higher. These are available from networks like Ionity, Fastned, and others.

App-only payment with no backup option

GreenWay stations require the GreenWay app to start a session. There are no contactless card readers or RFID pads. If the app fails or your phone dies, you cannot charge.

Symptoms

• No card reader or RFID pad visible on the charger
• Charger screen shows a QR code or 'Use app to start' message
• You arrived without the app installed and cannot begin a session
• Your phone battery is low and you are worried it will die during setup

How to Fix It

1. 1

   Download the GreenWay app before your trip

   This is non-negotiable for GreenWay stations. Install the app, create an account, and add a payment method while you have good internet and battery. Do this before you leave, not at the charger.

2. 2

   Charge your phone before arriving at the station

   Since you need your phone to start and monitor the session, make sure it has enough battery. Use your car's USB port or a power bank on the way.

3. 3

   Try a roaming app as a backup

   Some GreenWay stations are accessible through roaming providers like Plugsurfing, Shell Recharge, or Chargemap. Check your roaming app's map to see if the specific station is covered before counting on it.

4. 4

   Scan the QR code on the charger

   If you do not have the app, scan the QR code with your phone camera. It may direct you to the app store or, in some cases, to a web-based session start page.

App requires location services for charger activation

The GreenWay app needs location services turned on to activate a charger. Without it, the app cannot verify that you are at the station and will not let you start a session.

Symptoms

• App shows 'Enable location services' and will not proceed
• You can see the charger on the map but cannot start a session
• The 'Start charging' button is grayed out or unresponsive
• App shows your location incorrectly, placing you far from the station

How to Fix It

1. 1

   Enable location services for the GreenWay app

   Go to your phone settings, find the GreenWay app, and set location access to 'While Using' or 'Always.' On iPhone: Settings, Privacy, Location Services, GreenWay. On Android: Settings, Apps, GreenWay, Permissions, Location.

2. 2

   Make sure GPS is turned on, not just Wi-Fi location

   In some areas, Wi-Fi-based location is inaccurate. Turn on full GPS (high accuracy mode on Android) for a precise position fix at the station.

3. 3

   Step outside your vehicle briefly

   If GPS signal is weak (underground parking, dense urban area), step a few meters away from your car with your phone. This can help the GPS lock onto your position.

4. 4

   Try selecting the charger manually

   If the app cannot determine your location, try tapping on the station on the map manually or entering the charger's ID number (printed on the charger unit). Some app versions allow manual selection as a fallback.

Coverage gaps between cities

GreenWay's network is concentrated in and around cities. Between major cities, especially on secondary roads, there can be long stretches with no GreenWay stations.

Symptoms

• No GreenWay stations shown on the app map for 100+ km stretches
• The nearest GreenWay station requires a detour off your route
• You planned a trip assuming GreenWay coverage and ran into a gap
• Available stations between cities are AC-only (slow), not DC fast charging

How to Fix It

1. 1

   Plan your route and charging stops before leaving

   Use the GreenWay app or a route planner like ABRP (A Better Route Planner) to map out charging stops. Identify gaps in advance so you are not caught by surprise.

2. 2

   Have alternative charging networks ready

   Install apps for other networks that operate in the region. In Slovakia and Poland, look for Ionity, Shell Recharge, or Greencharge. In Czech Republic, check CEZ or PRE. Having multiple apps ensures you always have a fallback.

3. 3

   Charge to a higher level before entering a gap

   If you know there is a 150+ km stretch without fast chargers, charge to 90 or even 95% at the last available station. The slower charging speed above 80% is worth it if the alternative is running out of range.

4. 4

   Check for AC chargers as emergency backup

   Hotels, shopping centers, and some gas stations in Central Europe have AC chargers (Type 2, 11 to 22 kW). These are slow but can add enough range to reach the next fast charger. Many are accessible through Chargemap or Plugsurfing.

Charger screen errors in local language only

When a GreenWay charger displays an error, the message is often in Slovak, Polish, or Czech with no English translation. Understanding what went wrong is difficult.

Symptoms

• Error message appears in Slovak, Polish, or Czech
• You cannot tell if the error is temporary or requires support
• The charger stopped and you do not know why
• The error code is visible but the description is in a language you do not read

How to Fix It

1. 1

   Note the error code, not just the text

   Most error messages include a numeric or alphanumeric code (like E-101 or ERR_04). Write down or photograph the code. This is useful for support and often means the same thing regardless of language.

2. 2

   Use your phone camera to translate the screen

   Open Google Translate or Apple Translate, switch to camera mode, and point it at the charger screen. This gives a real-time translation of the error message.

3. 3

   Try unplugging and restarting the session

   Many error messages clear on a retry. Unplug, wait 15 seconds, plug back in, and start a new session through the app. Common errors like 'Communication timeout' resolve themselves.

4. 4

   Contact GreenWay support with the error code

   If the error persists, contact support through the GreenWay app. Provide the error code and the station ID (printed on the charger). GreenWay support can tell you whether the issue is temporary or requires a technician.

Power limited at older installations

Some older GreenWay stations deliver less than 150 kW. They may be rated at 50 kW or have degraded power output due to aging hardware.

Symptoms

• Charging speed maxes out at 50 kW on a station advertised as 150 kW
• The charger label says 150 kW but your vehicle never receives more than 50 kW
• Speed is significantly lower than what you get at newer GreenWay stations
• The app shows the station as 150 kW but the charger hardware looks older

How to Fix It

1. 1

   Check the charger label for the actual rated power

   The charger unit itself has a label showing its maximum output. Older GreenWay units may be rated at 50 kW despite the station listing showing 150 kW (which may refer to a newer unit at the same location).

2. 2

   Check if the station has multiple charger types

   Some GreenWay stations have both older 50 kW and newer 150 kW chargers. Make sure you are plugged into the newer, higher-power unit. It is usually the larger cabinet.

3. 3

   Verify your vehicle's battery level and temperature

   Your vehicle limits charging speed when the battery is above 60 to 80% or when the battery is cold. Check your dashboard to confirm the car is requesting more than what the charger delivers.

4. 4

   Use a different station if speed matters

   If you need faster charging and the station is limited, check the GreenWay app for a newer station nearby. Filter by power level to find 150 kW units specifically.