Volvo EX90 Charging at ChargePoint

Volvo EX90 Plugged In but the Charger Will Not Start

You connected the cable to your Volvo EX90 and nothing happens. No charging indicator on the screen, no confirmation from the charger. The EX90 supports Plug & Charge and multiple authentication methods, but when none of them work, you need to troubleshoot step by step.

Symptoms

• Charger displays an error after plugging in the EX90
• Charge port LED does not light up or stays amber
• 14.5-inch center screen shows no active charging session
• Charger screen says 'waiting for vehicle' or shows a timeout
• CCS connector plugs in but does not lock into the charge port

What to Do

1. 1

   Authenticate with the charger

   Check the charger's screen for payment instructions. Tap your RFID card, open the charging network's app, or use contactless payment. Plug & Charge should activate automatically on supported networks, but if it does not, use manual authentication.

2. 2

   Check the charge port on the left rear

   Open the charge port door fully. Check for ice, snow, or debris. In winter, gently clear any obstructions. Make sure the port cover is not partially blocking the connector.

3. 3

   Seat the connector firmly

   Push the CCS2 connector straight into the port until it clicks and locks. If it will not lock, pull it out and try again. Check that the connector pins are clean and undamaged.

4. 4

   Turn off scheduled charging

   On the center screen, go to Settings, then Charging. If a charging schedule is active, disable it or switch to 'charge immediately.' This is a common reason charging will not start at public chargers.

5. 5

   Restart the charging process

   Unplug the connector, lock and unlock the car using the Volvo Cars app or key, wait 15 seconds, then plug in again. This resets the charging communication.

Volvo EX90 Charger Payment Failed or Card Declined

You are at a public charger with your Volvo EX90 and the payment will not go through. The card reader rejects your card, the app throws an error, or Plug & Charge just does not activate. Payment issues at public chargers are one of the most common frustrations, and they have nothing to do with your car's charging system.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Plug & Charge does not activate when you connect the cable
• Charging app shows a payment error or insufficient balance
• Contactless payment terminal does not respond
• You cannot find any way to pay at the charger

What to Do

1. 1

   Check Plug & Charge status in the Volvo Cars app

   Open the Volvo Cars app and verify that Plug & Charge is enabled with a valid payment method. If the network supports it, try unplugging and reconnecting. If not, proceed to manual payment.

2. 2

   Try a different payment method

   Use a different credit or debit card, your phone's mobile wallet, or the charging network's app. Having multiple options avoids being stuck when one fails.

3. 3

   Check for pre-authorization holds

   Open your banking app and look for pending charges from the charging network. Multiple failed attempts may have placed several holds, reducing your available balance. Contact your bank if needed.

4. 4

   Use the charging network's app instead

   Find the network name on the charger. Download their app, create an account, add a payment method, and start the session through the app. This bypasses the physical payment terminal entirely.

5. 5

   Tap your RFID charging card

   If you carry an RFID card from a charging provider or roaming service, tap it on the charger's card reader. RFID cards are often more reliable than apps or contactless terminals.

Volvo EX90 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX90 expecting 250 kW and the 14.5-inch screen shows 60 kW. Or your wallbox is only delivering 3 kW instead of 11 kW. The EX90 has one of the fastest charging speeds in its class, but reaching that peak depends on battery temperature, state of charge, and the charger itself.

Symptoms

• DC fast charging speed well below the 250 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 40-50%
• Center screen shows lower power than the charger's rated output
• Charging session starts strong but slows down within 10 minutes

What to Do

1. 1

   Set the charger as your navigation destination

   Use Google Maps on the 14.5-inch center screen to navigate to the charging station. The EX90 will start preconditioning the battery automatically during the drive, preparing it for peak charging speed.

2. 2

   Check the charger's rated power

   Before plugging in, check the charger's label or the app for its maximum output. If the charger is rated at 150 kW, your EX90 cannot charge faster than 150 kW regardless of its 250 kW capability.

3. 3

   Check your state of charge

   For the fastest charging, arrive between 10-20%. The EX90's peak speeds are available at lower states of charge. Above 80%, charging will slow significantly.

4. 4

   Verify the charger is not sharing power

   Many chargers split power between two connectors. If someone is using the adjacent stall, both cars get reduced speeds. Move to a charger with both stalls free.

5. 5

   Check AC charge current settings

   If charging slowly on AC, check the EX90's settings to ensure the charge current limiter is set to maximum. Also verify your wallbox is properly wired for 3-phase.

6. 6

   Try a higher-powered charger

   To take advantage of the EX90's 250 kW capability, look for chargers rated at 300 kW or higher. These are available from networks like Ionity, Fastned, and others.

App shows "Available" but the charger is physically broken

The ChargePoint app shows a green status for a charger, but when you arrive, the unit is visibly damaged, has a blank screen, or displays an out-of-service message. This happens because ChargePoint's availability status depends on the charger reporting its own state, and a broken charger sometimes cannot report that it is broken.

Symptoms

• App shows the charger as available with a green icon
• Charger screen is blank, cracked, or showing an error message on site
• The connector is physically damaged or the cable is severed
• Other drivers at the station confirm the charger has been broken for days

How to Fix It

1. 1

   Check the other chargers at the same station

   ChargePoint stations often have multiple units. If one is broken, another unit nearby may work fine. Use the app to see all connectors at the location.

2. 2

   Report the broken charger in the ChargePoint app

   Open the station detail in the ChargePoint app, find the specific charger, and report the issue. Select the most accurate problem description. This updates the status for other drivers and alerts the station operator.

3. 3

   Check recent driver reports in the app

   The ChargePoint app sometimes shows recent check-ins or reports from other drivers. Before driving to a station, scroll down on the station detail page to see if anyone has reported issues recently.

4. 4

   Find the nearest alternative station

   In the ChargePoint app, tap "Find nearby" or zoom out on the map. Filter for DC fast chargers if you need speed. You can also check Google Maps or A Better Route Planner for non-ChargePoint alternatives.

RFID tap not registering

You tap your ChargePoint card on the reader and nothing happens. No beep, no screen change, no session. The RFID readers on ChargePoint stations can be finicky, especially on older European units.

Symptoms

• Tapping the RFID card produces no response from the charger
• The charger beeps but then shows "Authentication failed"
• The card works at some ChargePoint stations but not this one
• The RFID reader area is hard to locate on the charger

How to Fix It

1. 1

   Find the correct RFID reader location

   On ChargePoint stations, the RFID reader is sometimes in an unexpected spot. Look for a small RFID symbol, usually on the front face of the charger or near the screen. On some European units, it is on the side panel.

2. 2

   Hold the card flat and steady for three seconds

   Do not tap and pull away quickly. Press the card flat against the reader area and hold it still for a full three seconds. Some readers need this extra time.

3. 3

   Remove your card from any wallet or phone case

   If your ChargePoint card is in a wallet with other RFID cards or near your phone, interference can prevent the reader from detecting it. Hold the card alone against the reader.

4. 4

   Start the session from the ChargePoint app instead

   Open the ChargePoint app, find the station, select the specific charger, and tap "Start." This sends a start command over the network and does not rely on the physical RFID reader at all.

5. 5

   Check if your card is activated

   New ChargePoint RFID cards need to be activated in the ChargePoint app or on the website. Go to Account, then Cards, and verify your card is listed and active.

Session auto-terminates at 80%

Your charging session stops automatically when your battery reaches around 80%, even though you did not set a limit and wanted to charge further. Some ChargePoint stations, particularly those operated by local CPOs, have a configuration that ends sessions at 80% to free up the charger for the next driver.

Symptoms

• Charging stops at exactly 80% state of charge
• The ChargePoint app shows the session as "Complete" at 80%
• No error message on the charger, it simply stops
• Your car is still ready to accept more charge

How to Fix It

1. 1

   Check if this is a station policy

   Some station operators set an 80% cutoff on DC fast chargers to maximize charger availability. This is not a fault. Check the station detail in the ChargePoint app or look for signage at the station explaining time or charge limits.

2. 2

   Start a new session

   After the session ends at 80%, you can often start a new session on the same charger to continue charging. Unplug, wait 10 seconds, plug back in, and authenticate again.

3. 3

   Check your car's own charge limit

   Some EVs have a default charge limit set to 80% in the car's settings. Check your car's infotainment system under charging settings. If the limit is set to 80%, the car itself is stopping the session, not ChargePoint.

4. 4

   Switch to a different station if you need to charge above 80%

   If the 80% cutoff is a station policy and you need more charge, find a station without this restriction. AC chargers at destinations are usually a better choice for topping up above 80% because DC charging is very slow above that level anyway.

Waitlist feature not working

ChargePoint offers a waitlist feature that is supposed to notify you when a busy charger becomes available. In practice, the notifications are unreliable, especially at European stations.

Symptoms

• You joined the waitlist but never received a notification
• The notification arrived long after the charger became available
• The waitlist button is not available for some stations
• You received a notification but the charger was already taken by someone else

How to Fix It

1. 1

   Enable push notifications for the ChargePoint app

   Go to your phone's notification settings and make sure ChargePoint notifications are allowed. On iOS, check Settings, then Notifications, then ChargePoint. On Android, check App Info, then Notifications.

2. 2

   Stay within a reasonable distance of the station

   The waitlist is most useful when you are nearby, at a shop or restaurant within a few minutes of the charger. By the time you drive 15 minutes back to a station, the charger may already be taken again.

3. 3

   Do not rely solely on the waitlist

   Treat the waitlist as a nice-to-have, not a guarantee. Check the app manually every few minutes for availability updates, or look for an alternative station while you wait.

4. 4

   Check if the station supports the waitlist feature

   Not all ChargePoint stations have the waitlist enabled, particularly CPO-operated stations using ChargePoint hardware. If you do not see a waitlist option on the station page, the feature is not available there.

App interface confusing for European users

ChargePoint's app was designed primarily for the US market. European users sometimes encounter US-centric defaults, unfamiliar terminology, or features that do not apply in Europe.

Symptoms

• App defaults to miles instead of kilometers
• Pricing displayed in unexpected formats or currencies
• Filter options include connector types not used in Europe, like NACS
• Station details reference US-specific payment methods or loyalty programs
• Map loads centered on the US instead of your actual location

How to Fix It

1. 1

   Set your region and units in the app settings

   Open the ChargePoint app, go to Account or Settings, and look for region, language, or unit preferences. Set distance to kilometers and currency to your local currency.

2. 2

   Filter for CCS2 connectors

   When searching for stations, use the filter to show only CCS2 (the European DC fast charging standard). This hides US-only connector types from your results.

3. 3

   Check the station detail for European pricing

   Tap on a station to see the pricing breakdown. European ChargePoint stations typically show pricing in EUR, SEK, NOK, or GBP per kWh, sometimes with an additional per-minute fee after a certain duration.

4. 4

   Ignore US-specific features

   Features like ChargePoint Home integration or certain fleet management tools are designed for the US market. If something in the app does not seem relevant, it probably is not meant for European users.

CPO-operated station behaves differently than expected

Some stations use ChargePoint hardware and appear in the ChargePoint app, but they are owned and operated by a local charge point operator. These stations may have different pricing, access rules, or session limits than ChargePoint-owned stations.

Symptoms

• Pricing at the station does not match what you expected from ChargePoint
• Your ChargePoint account works but the session has unexpected restrictions
• The charger looks like ChargePoint but has another company's branding on it
• Customer support refers you to a different company for this station

How to Fix It

1. 1

   Check who operates the station

   In the ChargePoint app, the station detail page usually shows the operator or network name. If it says something other than ChargePoint, the station is CPO-operated and may have its own rules.

2. 2

   Read the pricing and terms on the station detail page

   CPO-operated stations set their own pricing. Check the ChargePoint app for the exact per-kWh rate and any time-based fees or session limits before you plug in.

3. 3

   Try the CPO's own app if ChargePoint authentication fails

   Some CPO stations accept ChargePoint cards but work more reliably with the operator's own app or RFID card. Look for the operator's name on the charger and download their app.

4. 4

   Contact the station operator for site-specific issues

   For problems like broken hardware, pricing errors, or access restrictions at a CPO-operated station, contact the operator directly. Their contact information is usually on the charger or in the station detail in the ChargePoint app.