Tesla Model S Charging at BP Pulse

Tesla Model S Charger Will Not Start a Session

You plugged in your Model S and nothing is happening. No green light on the charge port, no animation on the 17-inch touchscreen, just silence. Whether you are at a Supercharger, a third-party CCS2 station, or a home wallbox, there are a handful of common reasons the session will not begin.

Symptoms

• Charge port LED stays white or flashes red after plugging in the connector
• 17-inch touchscreen shows no charging animation or displays an error message
• Supercharger stall makes a click but does not begin delivering power
• CCS2 connector at a third-party station locks in but charging never starts
• Tesla app shows 'Not Charging' even though the cable is connected

What to Do

1. 1

   Check the charge port LED color

   Walk to the left rear of the car and look at the charge port light. White means ready but not connected. Blue means communicating. Green means charging. Red or amber means there is a fault. If it is white with the cable plugged in, remove and reseat the connector firmly.

2. 2

   Unplug and replug the connector

   Remove the connector completely, wait five seconds, then reinsert it until you hear the latch click. On CCS2 connectors, make sure both the top (AC pins) and bottom (DC pins) sections are seated properly.

3. 3

   Check for scheduled charging on the touchscreen

   On the 17-inch touchscreen, go to Controls, then Charging. If scheduled charging is active, you will see the planned start time. Tap to disable it or select 'Charge Now' to override the schedule.

4. 4

   Authorize the session at non-Tesla chargers

   At third-party CCS2 stations, check whether the charger requires you to start the session through an app, RFID card, or contactless payment. Plug & Charge works at supported stations, but many still require manual authorization.

5. 5

   Try a different stall or charger

   If you are at a Supercharger, move to a different stall. If you are at a third-party station, try the other connector. A faulted charger looks identical to a working one from the outside.

6. 6

   Restart the touchscreen

   Hold both scroll wheels on the steering wheel for about 10 seconds until the 17-inch touchscreen goes black and reboots. This resets the charging controller and fixes some communication glitches. The car stays on during the reboot.

Tesla Model S Payment Failed at Charging Station

You are plugged in and the charger is waiting for payment, or the Supercharger session will not start because of a billing issue. Payment problems are one of the most common reasons drivers get stuck at chargers, and the Model S has multiple ways to pay depending on where you are charging.

Symptoms

• Supercharger session will not start and the Tesla app shows a payment error
• Third-party CCS2 charger displays 'Authorization failed' after tapping your card
• RFID card is not recognized by the charger's reader
• Plug & Charge does not activate at a supported station
• Contactless bank card is rejected by the charger's payment terminal

What to Do

1. 1

   Check your Tesla account payment method

   Open the Tesla app on your phone. Go to Account, then Payment. Verify your credit card is current and has not expired. If the card was replaced, update the details. Supercharger sessions will not start without a valid payment method on file.

2. 2

   Try a different payment method at the charger

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having at least two payment methods gives you a backup when one does not work.

3. 3

   Scan the charger QR code for browser payment

   Most public chargers have a QR code on the unit. Scanning it with your phone opens the operator's payment page in your browser. You can usually pay with a credit card directly without downloading their app.

4. 4

   Check your banking app for blocked transactions

   Open your banking app and look for flagged or declined transactions. Some banks require you to approve the charge manually. Approve it and retry the payment at the charger.

5. 5

   Try Plug & Charge by replugging

   If the charger supports Plug & Charge, unplug the CCS2 connector from your Model S, wait a few seconds, and replug. Payment should authorize automatically through the cable. This only works if your Tesla account has Plug & Charge enabled and the charger supports ISO 15118.

6. 6

   Move to a Supercharger or a different station

   If you cannot resolve the payment issue, find a Tesla Supercharger using the nav on the 17-inch touchscreen. Supercharger billing is handled entirely through your Tesla account, bypassing third-party payment systems.

Tesla Model S Charging Slower Than Expected at Charger

You pulled into a Supercharger expecting 250 kW and the 17-inch touchscreen shows 80 kW. Or your home wallbox is crawling at 3 kW instead of 11 kW. The Model S has one of the fastest charging curves on the road, but reaching peak speed depends on battery temperature, state of charge, and a few settings you can check in under a minute.

Symptoms

• DC fast charging power well below 250 kW on the touchscreen despite a rated charger
• AC home charging stuck at 3-4 kW instead of the expected 11 kW on 3-phase
• Charging speed drops sharply after 40-50% on the touchscreen during DC fast charging
• Supercharger shows significantly lower kW than neighboring stalls
• Non-Tesla CCS2 charger delivers far less power than its rated maximum

What to Do

1. 1

   Check if the battery was preconditioned

   On the 17-inch touchscreen, tap the charging icon. If you see a snowflake icon or a message about conditioning, the battery was not warm enough when you arrived. Next time, navigate to the charger using Tesla nav at least 20-30 minutes before arrival so preconditioning kicks in automatically.

2. 2

   Check your current state of charge

   If you are above 50%, the slower speed is expected on the 95 kWh NCA pack. Peak power happens roughly between 5-30%. For the fastest charging stops on a road trip, arrive between 10-20%.

3. 3

   Move to an unpaired Supercharger stall

   Look at the stall numbers. If they are labeled in A/B pairs (3A/3B, 4A/4B), pick a stall where the paired stall is empty. At V3 or V4 Superchargers with the Magic Dock or the new V4 cable, this is not a concern.

4. 4

   Check the AC charge current limit on the touchscreen

   Go to Controls, then Charging on the touchscreen. Look for the charge current setting. Make sure it is set to the maximum amperage. This only affects AC charging at home or destination chargers, not Supercharging.

5. 5

   Try a different charger or stall

   If speeds remain low, the charger hardware may be degraded. Try another stall at the same location. On non-Tesla CCS2 stations, check the charger display for error codes or reduced power notices.

6. 6

   Check for a Tesla software update

   Go to Controls, then Software on the touchscreen. If an update is pending, install it. Tesla has adjusted charging curves through over-the-air updates in the past, sometimes improving peak speeds.

Contactless reader not responding

You tap your bank card or phone and nothing happens. The screen does not acknowledge the tap at all, or it briefly flashes and returns to the start screen.

Symptoms

• No beep or screen change after tapping your card
• Screen flashes 'Card read error' then resets
• Apple Pay or Google Pay shows 'Done' on your phone but the charger does not start
• Reader works on one unit but not the adjacent one

How to Fix It

1. 1

   Try a physical bank card instead of your phone

   Contactless phone payments sometimes fail on BP Pulse readers even when a physical card works fine. Hold the card flat against the reader for 2-3 seconds.

2. 2

   Check for a second tap point

   Some BP Pulse units have the contactless reader on the side panel rather than below the screen. Look for a card symbol printed on the housing.

3. 3

   Clean the reader surface

   Wipe dirt, rain, or condensation off the contactless reader area with your sleeve. Moisture on the sensor can prevent a clean read.

4. 4

   Start the session via the BP Pulse app instead

   Open the app, find the charger on the map, select the connector, and tap 'Start Charging.' This bypasses the physical reader entirely.

5. 5

   Try the other connector or an adjacent unit

   If the charger has two connectors, the other side may have a working reader. Or walk to the next unit. Contactless reader failures are often limited to one specific unit.

BP Pulse app crashing on Android

The app closes unexpectedly when you try to start a session, view the map, or enter payment details. This is more common on older Android versions and after recent app updates.

Symptoms

• App closes immediately after opening
• App freezes on the map screen then crashes
• Crash when tapping 'Start Charging' after selecting a connector
• 'App keeps stopping' notification from Android

How to Fix It

1. 1

   Force close and reopen the app

   Go to Android Settings, then Apps, then BP Pulse. Tap 'Force Stop,' wait a few seconds, then open the app again.

2. 2

   Clear the app cache

   In Settings, go to Apps, then BP Pulse, then Storage, then 'Clear Cache.' This removes temporary data without deleting your account. You will not need to log in again.

3. 3

   Check for an app update

   Open the Google Play Store, search for BP Pulse, and tap 'Update' if available. Crashes often follow a buggy release that gets patched within days.

4. 4

   Use contactless payment as a backup

   If the app will not cooperate, tap your bank card on the charger's contactless reader to start a session without the app.

5. 5

   Reinstall the app if crashes persist

   Uninstall BP Pulse, restart your phone, then reinstall from the Play Store. You will need to log in again, so make sure you know your BP Pulse account email.

Charger shows 'Out of Service' with no visible damage

The screen displays 'Out of Service' or 'Unavailable,' but the charger looks perfectly fine. No broken cables, no barrier tape, no obvious reason it should be offline.

Symptoms

• Screen stuck on 'Out of Service' message
• Charger appears available in the app but shows error on arrival
• Status light is red or off entirely
• Other chargers at the same location work fine

How to Fix It

1. 1

   Check the BP Pulse app for real-time status

   Open the app and look at this specific charger. If it shows as unavailable there too, the network has flagged it remotely. A maintenance team likely already knows.

2. 2

   Look for a reset button or power switch

   Some older BP Pulse units (especially former Chargemaster ones) have a small reset button behind a panel or near the base. Pressing it can sometimes clear a stuck error state.

3. 3

   Report it in the app

   Use the 'Report a problem' option on the charger's detail page in the BP Pulse app. This helps BP Pulse prioritize repairs and updates the status for other drivers.

4. 4

   Move to another charger

   An 'Out of Service' state usually means a backend fault, a communication issue with the network, or a pending software update. You cannot fix these yourself. Use another unit or location.

Charging session drops after 5-10 minutes

Charging starts normally, but the session ends on its own after a few minutes. Your car shows it is no longer receiving power, and the charger returns to the welcome screen.

Symptoms

• Car dashboard shows charging stopped unexpectedly
• Charger screen returns to 'Plug in to start' after a few minutes
• You receive a session-ended notification in the app with a very short session
• This happens repeatedly at the same charger

How to Fix It

1. 1

   Check the connector is fully seated

   Unplug the cable, inspect the connector pins for dirt or debris, and plug it back in firmly until you hear a click. A loose connection can cause the charger to drop the session.

2. 2

   Check your car's charge limit

   If your car's charge limit is set very close to the current battery level, some vehicles will stop charging almost immediately. Set the limit to 80% or higher and try again.

3. 3

   Try the other connector type

   If the charger offers both CCS2 and CHAdeMO and your car supports CCS2, make sure you are using CCS2. Using the wrong connector obviously will not fit, but a worn CCS2 connector on one side may work better on the other unit.

4. 4

   Start a new session at a different unit

   Repeated drops at the same charger point to a hardware fault on that unit. Move to another charger and try again.

5. 5

   Report the faulty unit

   Note the charger ID (printed on the unit) and report it via the BP Pulse app or call the BP Pulse support number shown on the charger. This helps get the unit serviced.

Subscription vs pay-as-you-go pricing confusion

BP Pulse offers a subscription plan with lower per-kWh rates and a pay-as-you-go option with higher rates. It is not always clear which pricing you are on, or whether the subscription is worth it for your usage.

Symptoms

• Charged a higher rate than expected on your receipt
• Unsure whether your subscription is active
• Signed up for subscription but still seeing non-member prices
• Cannot figure out how to switch between plans

How to Fix It

1. 1

   Check your plan status in the app

   Open the BP Pulse app, go to your account settings, and look for your subscription status. If it says 'Active,' you should be getting the lower rate automatically.

2. 2

   Make sure you are starting sessions through the app

   Subscription pricing only applies when you start the session via the BP Pulse app or RFID card linked to your account. Tapping a contactless bank card will charge you the standard pay-as-you-go rate.

3. 3

   Review your charging history for rate discrepancies

   In the app, go to Charging History and check the per-kWh rate on recent sessions. Compare this to the subscription rate listed on the BP Pulse pricing page.

4. 4

   Cancel or change your plan if needed

   You can manage your subscription in the app under Account, then Subscription. If you charge infrequently, pay-as-you-go may actually cost less overall despite the higher per-kWh rate.