Tesla Model 3 Charging at BP Pulse

Tesla Model 3 Charger Won't Start a Charging Session

You have plugged in your Model 3, the charge port light is doing something weird, and nothing is happening. This is one of the most common frustrations for EV drivers. The good news is that it is almost always fixable on the spot. The cause is usually authentication, the charge port latch, or the charger itself.

Symptoms

• Charge port LED flashes amber or red after plugging in the CCS2 connector
• Touchscreen shows an error message instead of the charging screen
• Charger display says 'Waiting for vehicle' or 'Authentication failed'
• Charge port will not open when pressing the button on the connector
• Supercharger session does not start automatically after plugging in

What to Do

1. 1

   Unplug and replug the connector firmly

   Pull the connector out completely. Wait 5 seconds. Push it back in firmly until you hear a click and the charge port LED turns green or starts pulsing. On CCS2, the lower DC pins need to seat fully.

2. 2

   Check the touchscreen for error messages

   Look at the charging screen on the touchscreen. It will tell you if there is an error, if scheduled charging is active, or if the car is waiting for something. If Scheduled Charging is delaying the session, tap 'Charge Now' to override it.

3. 3

   Authenticate with the charging network

   At non-Tesla chargers, open the network's app (Ionity, Shell Recharge, or whichever network). Start the session through the app, or tap your RFID card on the charger. At Tesla Superchargers, this step is automatic.

4. 4

   Try the manual charge port release if the port is stuck

   If the charge port will not open, try tapping your Tesla key card on the B-pillar and pressing the charge port door. You can also open it from the touchscreen under Controls. In freezing weather, pour lukewarm water around the port to melt ice. Never force it.

5. 5

   Restart the touchscreen

   Hold both scroll wheels on the steering wheel for about 10 seconds until the Tesla logo appears. This restarts the infotainment system and can clear communication errors between the car and the charger.

6. 6

   Try a different charger or stall

   If nothing works, the charger may be faulty. Move to a different stall or station. At Superchargers, the Tesla app shows stall availability in real time.

Tesla Model 3 Payment Failed at the Charging Station

You plugged in, everything looked fine, and then the charger says payment failed. Or the session will not start because authentication did not go through. Payment problems are different at Tesla Superchargers versus non-Tesla CCS2 chargers, so the fix depends on where you are.

Symptoms

• Charger display shows 'Payment failed' or 'Transaction declined' after tapping a card
• Tesla Supercharger session will not start and the Tesla app shows a billing error
• Non-Tesla CCS2 charger shows 'Authentication failed' after scanning RFID or using an app
• Contactless payment terminal on the charger does not respond to your bank card
• Charging starts but stops after a few seconds with a payment-related error on the charger screen

What to Do

1. 1

   Check if this is a Tesla Supercharger or a non-Tesla station

   At Tesla Superchargers, payment is automatic through your Tesla account. At non-Tesla CCS2 chargers, you need to authenticate separately. The fix is completely different for each.

2. 2

   For Superchargers: update your payment method in the Tesla app

   Open the Tesla app, go to Account, then Payment. Check that your card is current and not expired. Add a new card if needed. Then try the Supercharger again. The session should start automatically after plugging in.

3. 3

   For non-Tesla chargers: authenticate through the network app

   Open the charging network's app (Ionity, Shell Recharge, Virta, or whichever network runs the charger). Select the charger, start the session, then plug in. Make sure the app shows your payment method is valid.

4. 4

   Try a different payment method at the charger

   If the contactless terminal failed, try the network's app instead. If the app failed, try an RFID card. If you do not have the network's app, some chargers accept ad-hoc payments through a QR code on the charger.

5. 5

   Call your bank if repeated transactions are declined

   If your card keeps getting declined at chargers, your bank may be blocking charging transactions. Call the number on the back of your card and let them know you are making EV charging payments. They can whitelist these merchants.

6. 6

   Move to a different charger if the payment terminal is broken

   If the charger's payment terminal is physically unresponsive, try a different stall. Report the broken terminal through the network's app so they can fix it.

Tesla Model 3 Charging Slower Than Expected at Charger

You plugged in your Model 3 expecting 175 kW and the touchscreen shows 50 kW. Or your home wallbox is stuck at 3 kW instead of 11 kW. Slow charging on the Model 3 is almost never a defect. It is usually the battery temperature, a charger limitation, or a setting you can fix on the touchscreen in under a minute.

Symptoms

• DC fast charging power well below the 175 kW maximum shown on the touchscreen
• AC home charging stuck at 3-4 kW instead of the expected 11 kW
• Charging speed drops sharply after reaching 50-60% on the touchscreen
• Supercharger shows lower kW than the stall is rated for
• Touchscreen charging animation shows a slow trickle instead of rapid charging

What to Do

1. 1

   Check the battery temperature on the touchscreen

   Tap the charging icon on the touchscreen. If the battery is cold, you will see a snowflake icon or a message about reduced charging speed. To fix this, use the Tesla nav to route to a Supercharger. The car will automatically precondition the battery during the drive.

2. 2

   Check your state of charge

   If you are above 80%, the slower speed is expected. For the fastest DC charging, arrive between 10-20%. The Model 3 LFP hits peak power in the 10-50% range.

3. 3

   Move to an unpaired Supercharger stall

   Look at the stall numbers. If they are labeled in pairs (1A/1B, 2A/2B), pick a stall where the paired stall is empty. At V3 or V4 Superchargers, this is not an issue.

4. 4

   Check the AC charge current limit

   On the touchscreen, go to Controls, then Charging. Look for the charge current slider or setting. Make sure it is set to the maximum value. This only affects AC charging, not Supercharging.

5. 5

   Try a different charger or stall

   If speeds are still low, the charger may be degraded. Try a different stall at the same location. On non-Tesla CCS chargers, some stations deliver less power than advertised.

6. 6

   Check for a software update

   Go to Controls, then Software on the touchscreen. If an update is available, install it. Tesla occasionally adjusts charging curves through software updates.

Contactless reader not responding

You tap your bank card or phone and nothing happens. The screen does not acknowledge the tap at all, or it briefly flashes and returns to the start screen.

Symptoms

• No beep or screen change after tapping your card
• Screen flashes 'Card read error' then resets
• Apple Pay or Google Pay shows 'Done' on your phone but the charger does not start
• Reader works on one unit but not the adjacent one

How to Fix It

1. 1

   Try a physical bank card instead of your phone

   Contactless phone payments sometimes fail on BP Pulse readers even when a physical card works fine. Hold the card flat against the reader for 2-3 seconds.

2. 2

   Check for a second tap point

   Some BP Pulse units have the contactless reader on the side panel rather than below the screen. Look for a card symbol printed on the housing.

3. 3

   Clean the reader surface

   Wipe dirt, rain, or condensation off the contactless reader area with your sleeve. Moisture on the sensor can prevent a clean read.

4. 4

   Start the session via the BP Pulse app instead

   Open the app, find the charger on the map, select the connector, and tap 'Start Charging.' This bypasses the physical reader entirely.

5. 5

   Try the other connector or an adjacent unit

   If the charger has two connectors, the other side may have a working reader. Or walk to the next unit. Contactless reader failures are often limited to one specific unit.

BP Pulse app crashing on Android

The app closes unexpectedly when you try to start a session, view the map, or enter payment details. This is more common on older Android versions and after recent app updates.

Symptoms

• App closes immediately after opening
• App freezes on the map screen then crashes
• Crash when tapping 'Start Charging' after selecting a connector
• 'App keeps stopping' notification from Android

How to Fix It

1. 1

   Force close and reopen the app

   Go to Android Settings, then Apps, then BP Pulse. Tap 'Force Stop,' wait a few seconds, then open the app again.

2. 2

   Clear the app cache

   In Settings, go to Apps, then BP Pulse, then Storage, then 'Clear Cache.' This removes temporary data without deleting your account. You will not need to log in again.

3. 3

   Check for an app update

   Open the Google Play Store, search for BP Pulse, and tap 'Update' if available. Crashes often follow a buggy release that gets patched within days.

4. 4

   Use contactless payment as a backup

   If the app will not cooperate, tap your bank card on the charger's contactless reader to start a session without the app.

5. 5

   Reinstall the app if crashes persist

   Uninstall BP Pulse, restart your phone, then reinstall from the Play Store. You will need to log in again, so make sure you know your BP Pulse account email.

Charger shows 'Out of Service' with no visible damage

The screen displays 'Out of Service' or 'Unavailable,' but the charger looks perfectly fine. No broken cables, no barrier tape, no obvious reason it should be offline.

Symptoms

• Screen stuck on 'Out of Service' message
• Charger appears available in the app but shows error on arrival
• Status light is red or off entirely
• Other chargers at the same location work fine

How to Fix It

1. 1

   Check the BP Pulse app for real-time status

   Open the app and look at this specific charger. If it shows as unavailable there too, the network has flagged it remotely. A maintenance team likely already knows.

2. 2

   Look for a reset button or power switch

   Some older BP Pulse units (especially former Chargemaster ones) have a small reset button behind a panel or near the base. Pressing it can sometimes clear a stuck error state.

3. 3

   Report it in the app

   Use the 'Report a problem' option on the charger's detail page in the BP Pulse app. This helps BP Pulse prioritize repairs and updates the status for other drivers.

4. 4

   Move to another charger

   An 'Out of Service' state usually means a backend fault, a communication issue with the network, or a pending software update. You cannot fix these yourself. Use another unit or location.

Charging session drops after 5-10 minutes

Charging starts normally, but the session ends on its own after a few minutes. Your car shows it is no longer receiving power, and the charger returns to the welcome screen.

Symptoms

• Car dashboard shows charging stopped unexpectedly
• Charger screen returns to 'Plug in to start' after a few minutes
• You receive a session-ended notification in the app with a very short session
• This happens repeatedly at the same charger

How to Fix It

1. 1

   Check the connector is fully seated

   Unplug the cable, inspect the connector pins for dirt or debris, and plug it back in firmly until you hear a click. A loose connection can cause the charger to drop the session.

2. 2

   Check your car's charge limit

   If your car's charge limit is set very close to the current battery level, some vehicles will stop charging almost immediately. Set the limit to 80% or higher and try again.

3. 3

   Try the other connector type

   If the charger offers both CCS2 and CHAdeMO and your car supports CCS2, make sure you are using CCS2. Using the wrong connector obviously will not fit, but a worn CCS2 connector on one side may work better on the other unit.

4. 4

   Start a new session at a different unit

   Repeated drops at the same charger point to a hardware fault on that unit. Move to another charger and try again.

5. 5

   Report the faulty unit

   Note the charger ID (printed on the unit) and report it via the BP Pulse app or call the BP Pulse support number shown on the charger. This helps get the unit serviced.

Subscription vs pay-as-you-go pricing confusion

BP Pulse offers a subscription plan with lower per-kWh rates and a pay-as-you-go option with higher rates. It is not always clear which pricing you are on, or whether the subscription is worth it for your usage.

Symptoms

• Charged a higher rate than expected on your receipt
• Unsure whether your subscription is active
• Signed up for subscription but still seeing non-member prices
• Cannot figure out how to switch between plans

How to Fix It

1. 1

   Check your plan status in the app

   Open the BP Pulse app, go to your account settings, and look for your subscription status. If it says 'Active,' you should be getting the lower rate automatically.

2. 2

   Make sure you are starting sessions through the app

   Subscription pricing only applies when you start the session via the BP Pulse app or RFID card linked to your account. Tapping a contactless bank card will charge you the standard pay-as-you-go rate.

3. 3

   Review your charging history for rate discrepancies

   In the app, go to Charging History and check the per-kWh rate on recent sessions. Compare this to the subscription rate listed on the BP Pulse pricing page.

4. 4

   Cancel or change your plan if needed

   You can manage your subscription in the app under Account, then Subscription. If you charge infrequently, pay-as-you-go may actually cost less overall despite the higher per-kWh rate.