Polestar 2 Charging at Atlante

Polestar 2 Charger Won't Start or Begin Charging

You have plugged in your Polestar 2, the connector clicked, but nothing happens. The center display stays silent or shows an error. This is frustrating, but it is almost always fixable on the spot without calling support.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the center display
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• Polestar 2 charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Center display briefly shows charging screen, then returns to idle

What to Do

1. 1

   Unplug and reconnect firmly

   Remove the CCS2 or Type 2 connector, wait 10 seconds, then reinsert it with a firm push until you hear a clear click. Watch the charge port LED on the Polestar 2 for a steady light.

2. 2

   Check for a charging schedule

   On the center display, go to Settings, then Charging. If a charging schedule is active, disable it or set it to 'Direct' so the car charges immediately when plugged in.

3. 3

   Restart the charger session

   On the charger, end the current session if one is shown. Then start a new session by tapping your RFID card or restarting in the charger's app. Some chargers have a physical start/stop button.

4. 4

   Try Plug & Charge or a different payment method

   If your Polestar 2 has Plug & Charge enabled, check the charger supports it. Otherwise, switch to a different RFID card, contactless payment, or the charger operator's app.

5. 5

   Reboot the car's infotainment system

   Press and hold the home button on the center display for about 15 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication module.

6. 6

   Try a different charger or cable

   If the station has multiple stalls, move to a different one. If you are using a tethered cable, try bringing your own Type 2 cable. A faulty charger cable is more common than a faulty car.

Polestar 2 Charging Payment Failed at the Station

You are at the charger, your Polestar 2 is ready, but the payment will not go through. The charger says 'Authorization failed' or just does nothing after you tap your card. Payment issues are one of the most common reasons a charging session never starts, and they are usually fixable in a couple of minutes.

Symptoms

• Charger screen shows 'Authorization failed' or 'Payment declined' after tapping your card or RFID
• Charger app shows an error when trying to start a remote session for your Polestar 2
• Contactless bank card is declined even though it works at shops
• Plug & Charge does not activate automatically after plugging in the CCS2 connector
• Charger accepts payment but the session immediately ends with a zero-kWh charge

What to Do

1. 1

   Check if Plug & Charge is enabled

   On the Polestar 2 center display, go to Settings, then Charging. Confirm Plug & Charge is turned on. If it is on but the charger did not start automatically, this station likely does not support it. Use a different payment method.

2. 2

   Try the charger operator's app

   Look for the operator name on the charger (Ionity, Shell Recharge, Allego, etc.). Download their app if you do not have it, add a payment method, and start the session through the app. Make sure you select the correct stall number shown on the charger.

3. 3

   Try a different RFID card or payment method

   If you carry multiple charging cards, try a different one. Some roaming cards work across many networks. If you only have one card, try contactless payment with your bank card or phone if the charger supports it.

4. 4

   Check your bank card's available balance

   Open your banking app and check that you have enough available balance for the pre-authorization hold, which can be up to 50 EUR even for a short charge. Pending holds from previous charging sessions can temporarily reduce your available balance.

5. 5

   Restart the charger and try again

   Some chargers have a stop/reset button. Press it, wait for the screen to return to the start screen, then begin a fresh session. If there is no button, unplug your Polestar 2, wait 30 seconds, and replug.

6. 6

   Move to a different charger

   If nothing works at this stall, try a different stall at the same station. Payment terminals can fail independently. If the entire station is down, find the nearest alternative using the charger map on your Polestar 2 center display or Google Maps.

Polestar 2 Charging Slower Than Expected

You plugged in your Polestar 2 expecting 149 kW and the screen shows 40 kW. Or your home charger is stuck at 3 kW instead of 11 kW. Slow charging on the Polestar 2 is almost never a defect. It is usually the battery temperature, the charger itself, or a setting you can fix in two minutes.

Symptoms

• DC fast charging speed well below the 149 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops significantly after reaching 50-60%
• Charging session starts normally but slows down quickly
• Dashboard shows lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature

   Look at the charging screen on the center display. If the battery is cold (common in winter), drive for 15-20 minutes before charging or use the preconditioning feature through the Polestar app before arriving at the charger.

2. 2

   Check your state of charge

   If you are above 80%, the slower speed is normal. For fastest charging, arrive at the charger between 10-20% and charge to 80%.

3. 3

   Verify the charger is not shared

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if available.

4. 4

   Check the AC charge current setting

   In the Polestar 2, go to Settings, then Charging. Make sure the charge current limiter is set to maximum. If it shows a lower value, increase it.

5. 5

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Try a different charger at the same location or a different charging station.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.