Polestar 2 Charging at Allego

Polestar 2 Charger Won't Start or Begin Charging

You have plugged in your Polestar 2, the connector clicked, but nothing happens. The center display stays silent or shows an error. This is frustrating, but it is almost always fixable on the spot without calling support.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the center display
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• Polestar 2 charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Center display briefly shows charging screen, then returns to idle

What to Do

1. 1

   Unplug and reconnect firmly

   Remove the CCS2 or Type 2 connector, wait 10 seconds, then reinsert it with a firm push until you hear a clear click. Watch the charge port LED on the Polestar 2 for a steady light.

2. 2

   Check for a charging schedule

   On the center display, go to Settings, then Charging. If a charging schedule is active, disable it or set it to 'Direct' so the car charges immediately when plugged in.

3. 3

   Restart the charger session

   On the charger, end the current session if one is shown. Then start a new session by tapping your RFID card or restarting in the charger's app. Some chargers have a physical start/stop button.

4. 4

   Try Plug & Charge or a different payment method

   If your Polestar 2 has Plug & Charge enabled, check the charger supports it. Otherwise, switch to a different RFID card, contactless payment, or the charger operator's app.

5. 5

   Reboot the car's infotainment system

   Press and hold the home button on the center display for about 15 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication module.

6. 6

   Try a different charger or cable

   If the station has multiple stalls, move to a different one. If you are using a tethered cable, try bringing your own Type 2 cable. A faulty charger cable is more common than a faulty car.

Polestar 2 Charging Payment Failed at the Station

You are at the charger, your Polestar 2 is ready, but the payment will not go through. The charger says 'Authorization failed' or just does nothing after you tap your card. Payment issues are one of the most common reasons a charging session never starts, and they are usually fixable in a couple of minutes.

Symptoms

• Charger screen shows 'Authorization failed' or 'Payment declined' after tapping your card or RFID
• Charger app shows an error when trying to start a remote session for your Polestar 2
• Contactless bank card is declined even though it works at shops
• Plug & Charge does not activate automatically after plugging in the CCS2 connector
• Charger accepts payment but the session immediately ends with a zero-kWh charge

What to Do

1. 1

   Check if Plug & Charge is enabled

   On the Polestar 2 center display, go to Settings, then Charging. Confirm Plug & Charge is turned on. If it is on but the charger did not start automatically, this station likely does not support it. Use a different payment method.

2. 2

   Try the charger operator's app

   Look for the operator name on the charger (Ionity, Shell Recharge, Allego, etc.). Download their app if you do not have it, add a payment method, and start the session through the app. Make sure you select the correct stall number shown on the charger.

3. 3

   Try a different RFID card or payment method

   If you carry multiple charging cards, try a different one. Some roaming cards work across many networks. If you only have one card, try contactless payment with your bank card or phone if the charger supports it.

4. 4

   Check your bank card's available balance

   Open your banking app and check that you have enough available balance for the pre-authorization hold, which can be up to 50 EUR even for a short charge. Pending holds from previous charging sessions can temporarily reduce your available balance.

5. 5

   Restart the charger and try again

   Some chargers have a stop/reset button. Press it, wait for the screen to return to the start screen, then begin a fresh session. If there is no button, unplug your Polestar 2, wait 30 seconds, and replug.

6. 6

   Move to a different charger

   If nothing works at this stall, try a different stall at the same station. Payment terminals can fail independently. If the entire station is down, find the nearest alternative using the charger map on your Polestar 2 center display or Google Maps.

Polestar 2 Charging Slower Than Expected

You plugged in your Polestar 2 expecting 149 kW and the screen shows 40 kW. Or your home charger is stuck at 3 kW instead of 11 kW. Slow charging on the Polestar 2 is almost never a defect. It is usually the battery temperature, the charger itself, or a setting you can fix in two minutes.

Symptoms

• DC fast charging speed well below the 149 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops significantly after reaching 50-60%
• Charging session starts normally but slows down quickly
• Dashboard shows lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature

   Look at the charging screen on the center display. If the battery is cold (common in winter), drive for 15-20 minutes before charging or use the preconditioning feature through the Polestar app before arriving at the charger.

2. 2

   Check your state of charge

   If you are above 80%, the slower speed is normal. For fastest charging, arrive at the charger between 10-20% and charge to 80%.

3. 3

   Verify the charger is not shared

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if available.

4. 4

   Check the AC charge current setting

   In the Polestar 2, go to Settings, then Charging. Make sure the charge current limiter is set to maximum. If it shows a lower value, increase it.

5. 5

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Try a different charger at the same location or a different charging station.

Allego app not starting a session

You open the Allego app, select the charger, tap 'Start,' and nothing happens. The app may spin, show an error, or claim the charger is offline even though the screen in front of you says otherwise.

Symptoms

• Allego app shows a loading spinner that never finishes
• 'Charger unavailable' in the app but the physical charger looks operational
• App crashes when tapping 'Start Charging'
• Session appears to start in the app but the charger does not begin delivering power

How to Fix It

1. 1

   Make sure you selected the correct charger and connector

   Allego stations often have multiple charging points. Each one has its own ID, usually printed on a sticker near the connector. Match this ID to the one shown in the Allego app. Selecting the wrong point is the most common reason a session will not start.

2. 2

   Plug in the cable before starting the session in the app

   Most Allego chargers require the cable to be connected to your car first. The charger needs to detect a vehicle before it will accept a start command from the app.

3. 3

   Close and reopen the Allego app

   Force-close the app completely (swipe it away from your recent apps), wait a few seconds, and reopen it. Try starting the session again.

4. 4

   Scan the QR code on the charger instead

   Most Allego chargers have a QR code that opens a web-based payment page. This works independently of the Allego app and lets you pay with a credit card without needing an account.

5. 5

   Use an RFID card from a roaming provider

   If you have an RFID card from a provider like Shell Recharge, Plugsurfing, or Chargemap, hold it against the reader on the charger. This bypasses the Allego app entirely.

Charger not appearing in the Allego app

You are standing in front of a physical Allego charger, but it does not show up on the Allego app map. The charger is clearly operational and other drivers are using it.

Symptoms

• Charger location is missing from the the Allego app map entirely
• App shows the location but with zero available connectors
• Charger appears under a different brand name in other apps but not in the Allego app
• Newly installed charger not yet listed

How to Fix It

1. 1

   Check if the charger is operated under a different brand

   Allego operates under various local labels in different countries. The charger might be listed under the local brand name rather than 'Allego' in some apps. Look for a sticker or sign on the charger that shows the operator name and EVSE ID.

2. 2

   Search by charger ID instead of location

   In the Allego app, try the search function and enter the charger's EVSE ID (printed on the unit, usually starting with a country code like DE*, NL*, or FR*). This can find chargers that are not correctly placed on the map.

3. 3

   Use the QR code on the charger

   Scan the QR code on the charger with your phone camera. This will open a direct link to start a session, even if the charger is missing from the app map.

4. 4

   Try a different charging app

   Allego chargers are accessible through many roaming providers. Open an app like Chargemap, Shell Recharge, or Plugsurfing and search for the same location. You may be able to start the session there.

Third-party RFID card not accepted

You hold your RFID card from another provider against the reader and the charger beeps but rejects it, or nothing happens at all.

Symptoms

• Charger beeps once but displays 'Card not recognized'
• No reaction when holding the RFID card to the reader
• Card works at other networks but not at this Allego charger
• 'Authorization failed' message on the charger screen

How to Fix It

1. 1

   Check if your roaming provider covers Allego

   Not all RFID providers have roaming agreements with Allego. Check your provider's app or website to confirm Allego is listed in their coverage. Some providers cover only certain Allego locations.

2. 2

   Hold the card flat and steady for 3 seconds

   Do not wave or tap the card. Place it flat against the reader and hold it still. Allego readers can be slower to respond than some other networks.

3. 3

   Try a different position on the reader

   The RFID antenna inside the reader has a specific sweet spot. Move your card slowly across the reader surface until you get a response. On some Allego chargers, the reader is on the right side panel rather than the front.

4. 4

   Check your RFID card is activated

   Some providers require you to activate your RFID card in their app before first use. Open your provider's app and look for card activation or card management settings.

5. 5

   Fall back to QR code or Allego app

   If your RFID card will not work, scan the QR code on the charger for direct credit card payment, or download the Allego app and register to start the session digitally.

Long delay before charging actually starts

You have authenticated and the charger says it is starting, but 30 seconds, sometimes over a minute, passes before any power flows to your car.

Symptoms

• Charger screen says 'Starting' or 'Initializing' for over 30 seconds
• Car shows 'Waiting for charger' or 'Preparing'
• Power reading stays at 0 kW for a full minute after authentication
• You wonder if you should unplug and try again

How to Fix It

1. 1

   Wait at least 90 seconds before taking action

   Allego high-power chargers perform a communication handshake with your car before delivering power. This includes safety checks, voltage negotiation, and isolation testing. A 30-60 second delay is normal, especially on 350 kW units.

2. 2

   Do not unplug during the initialization phase

   Unplugging and re-plugging resets the entire handshake process. If the charger screen shows any progress (status messages, icons changing), let it complete.

3. 3

   Check if your car's charge port is locked

   The connector should be locked into your car's charge port during initialization. If you can wiggle the connector freely, it may not be fully inserted. Push it in firmly and listen for the lock click.

4. 4

   If nothing happens after 2 minutes, restart the session

   Unplug the connector, wait 10 seconds, plug it back in, and authenticate again. If the delay repeats, try a different connector or charger at the same station.

Charging power much lower than advertised

The charger is rated for 350 kW, but your car is only pulling 50 kW or less. The session is working, just far slower than expected.

Symptoms

• Car or charger display shows 40-80 kW on a 350 kW charger
• Estimated charge time is much longer than expected
• Power started high but dropped dramatically within minutes
• Other cars at the same station seem to charge faster

How to Fix It

1. 1

   Check your battery level

   DC charging slows significantly above 60-70% state of charge on most cars. If your battery is already at 65% or higher, the reduced speed is your car protecting its battery, not a charger problem.

2. 2

   Check your car's maximum DC charging rate

   A 350 kW charger can deliver up to 350 kW, but your car decides how much to accept. Many EVs top out at 100-150 kW. Check your car's specifications for its maximum DC charging speed.

3. 3

   Consider battery temperature

   Cold batteries charge slowly. If you have been parked for hours in cold weather without preconditioning, your car may limit charging to 30-60 kW until the battery warms up. Some cars let you precondition the battery by setting the charger as your navigation destination.

4. 4

   Check if the station is power-sharing

   Some Allego stations share power between multiple chargers. If three cars are charging simultaneously, each one may get less than the maximum. This is normal at shared-power sites.

5. 5

   Try a different connector at the same station

   Occasionally one connector delivers less power due to a hardware limitation. If you are getting unusually low power even at a low battery level, unplug and try the next unit.