Mercedes-Benz EQS Charging at BP Pulse

Mercedes-Benz EQS Charger Won't Start a Session

You connected the CCS2 cable to your EQS's right rear charge port, but the Hyperscreen shows no charging activity. No power flowing, no progress. This is frustrating, especially in a flagship sedan where everything should just work. The cause is usually authentication, cable seating, or the charger itself, not the EQS.

Symptoms

• CCS2 connector plugged in but the Hyperscreen shows no charging activity
• Charger screen displays an error or stays idle after authentication attempt
• Plug & Charge does not authenticate automatically at a supported station
• Charge port LED does not illuminate or blinks an error pattern
• Mercedes me app shows the EQS as connected but not charging

What to Do

1. 1

   Remove and firmly reseat the CCS2 connector

   Pull the connector out of the right rear charge port. Check for debris or moisture. Push it back in straight and firm until you hear a click and see the charge port LED respond. The CCS2 connector is heavy, so support it with both hands to ensure proper alignment.

2. 2

   Authenticate manually if Plug & Charge failed

   Open the charging network's app and start the session by scanning the QR code or selecting the charger. If you have an RFID card for this network, tap it on the reader. Do not wait for Plug & Charge if it did not work within 30 seconds.

3. 3

   Disable scheduled charging in MBUX

   On the Hyperscreen, open Settings, then Charging. Turn off any departure time or scheduled charging window. At a public charger, you want charging to start immediately. Re-enable scheduled charging when you are back at your home wallbox.

4. 4

   Lock and unlock the EQS to reset the charge controller

   Use the key or Mercedes me app to lock the car. Wait 15 seconds, then unlock. This resets the charge port locking mechanism and the onboard charging communication module. Reconnect the cable after unlocking.

5. 5

   Try a different connector or charger at the station

   If the station has multiple CCS2 connectors, try a different one. If the entire station seems unresponsive, use MBUX navigation to find another nearby charger. Report the faulty charger through the network's app.

Mercedes-Benz EQS Payment Failed at Charging Station

You are standing next to your EQS at a public charger and payment will not go through. Plug & Charge did not activate, the app shows an error, or your card was declined. Payment failures are one of the most common reasons charging sessions do not start. With the EQS, you have multiple authentication options to try before giving up.

Symptoms

• Plug & Charge does not authenticate when the CCS2 cable is connected
• Contactless card declined at the charger's payment terminal
• Mercedes me Charge or the network's app shows a payment error
• RFID card not recognized by the charger reader
• Session starts but stops immediately with a billing-related error

What to Do

1. 1

   Try Plug & Charge by connecting the cable

   Plug the CCS2 connector into the EQS's right rear charge port. Wait up to 30 seconds for Plug & Charge to authenticate. Check the Hyperscreen for a charging confirmation. If nothing happens after 30 seconds, Plug & Charge is not working at this station.

2. 2

   Use the charging network's app to start the session

   Open the app for the charging network shown on the charger. Scan the QR code or enter the charger ID. Start the session through the app. Verify your payment method in the app is valid and not expired.

3. 3

   Try contactless payment at the charger terminal

   If the charger has a contactless payment terminal, tap your bank card, Apple Pay, or Google Pay. If the first card is declined, try a different one. Some terminals accept only certain card brands.

4. 4

   Verify your Mercedes me Charge account

   Open the Mercedes me app. Go to Charge settings and check that Plug & Charge is enabled and your payment method is current. If you recently changed your payment method, it may need time to sync. Try restarting the Mercedes me app.

5. 5

   Try a different RFID card or roaming provider

   If you carry multiple RFID cards, try another network. Roaming providers with broad European coverage (Chargemap, Maingau, Shell Recharge) can fill gaps where Mercedes me Charge does not reach.

6. 6

   Find an alternative charger nearby

   If payment fails on this charger entirely, use the Hyperscreen to find another station nearby. A different charging network may accept your payment method. Filter by the networks you know work with your cards.

Mercedes-Benz EQS Charging Slower Than Expected

You plugged in your EQS at a 300 kW charger expecting close to 200 kW, but the Hyperscreen shows 50 kW. Or your home wallbox is stuck at 3.6 kW instead of 11 kW (or 22 kW if you have the optional upgrade). The EQS has a huge 118 kWh battery that can take a while to warm up. Slow charging is almost always temperature, state of charge, or the charger, not a defect.

Symptoms

• DC fast charging speed well below the 200 kW maximum shown on the Hyperscreen
• AC charging stuck at 3-4 kW instead of 11 kW or 22 kW
• Charging speed drops sharply after reaching 50-60% state of charge
• Charging session starts at reasonable speed but slows within minutes
• The 118 kWh battery takes significantly longer to charge than expected

What to Do

1. 1

   Route to the charger using MBUX navigation

   Enter the charging station as your destination on the Hyperscreen or MBUX. This activates automatic battery preconditioning for the 118 kWh pack. The EQS will display a preconditioning notification. Given the large battery, start routing at least 20-30 minutes before arrival for maximum benefit in cold weather.

2. 2

   Check your state of charge before expecting peak speed

   The EQS reaches 200 kW only at lower state of charge levels. For the fastest DC charging, arrive between 10-20%. If you are above 60%, the speed reduction is normal. With 580 km of range, you often do not need to charge above 80% on road trips.

3. 3

   Verify the charger can deliver the speed you expect

   Check the charger's rated output on the unit itself or in the charging app. A 50 kW charger will never give your EQS more than 50 kW. Look for chargers rated 150 kW or higher to take advantage of the EQS's capabilities. Avoid stalls paired with another vehicle.

4. 4

   Check AC charging settings and wallbox compatibility

   Open the charging settings in MBUX. Confirm the charge current is set to maximum. If you have the optional 22 kW onboard charger, verify your wallbox is 3-phase 32A. For the standard 11 kW charger, you need at least 3-phase 16A.

5. 5

   Check if Plug & Charge negotiated the correct power

   The EQS supports Plug & Charge. Occasionally, authentication issues cause the charger to default to a lower power tier. Unplug from the right rear charge port, wait 30 seconds, and reconnect. Check MBUX for any authentication errors.

6. 6

   Try a different charger

   If the speed is still low after checking all settings, try a different charger. Some chargers degrade over time. Use MBUX navigation or the Mercedes me app to find a high-power charger (150 kW+) nearby.

Contactless reader not responding

You tap your bank card or phone and nothing happens. The screen does not acknowledge the tap at all, or it briefly flashes and returns to the start screen.

Symptoms

• No beep or screen change after tapping your card
• Screen flashes 'Card read error' then resets
• Apple Pay or Google Pay shows 'Done' on your phone but the charger does not start
• Reader works on one unit but not the adjacent one

How to Fix It

1. 1

   Try a physical bank card instead of your phone

   Contactless phone payments sometimes fail on BP Pulse readers even when a physical card works fine. Hold the card flat against the reader for 2-3 seconds.

2. 2

   Check for a second tap point

   Some BP Pulse units have the contactless reader on the side panel rather than below the screen. Look for a card symbol printed on the housing.

3. 3

   Clean the reader surface

   Wipe dirt, rain, or condensation off the contactless reader area with your sleeve. Moisture on the sensor can prevent a clean read.

4. 4

   Start the session via the BP Pulse app instead

   Open the app, find the charger on the map, select the connector, and tap 'Start Charging.' This bypasses the physical reader entirely.

5. 5

   Try the other connector or an adjacent unit

   If the charger has two connectors, the other side may have a working reader. Or walk to the next unit. Contactless reader failures are often limited to one specific unit.

BP Pulse app crashing on Android

The app closes unexpectedly when you try to start a session, view the map, or enter payment details. This is more common on older Android versions and after recent app updates.

Symptoms

• App closes immediately after opening
• App freezes on the map screen then crashes
• Crash when tapping 'Start Charging' after selecting a connector
• 'App keeps stopping' notification from Android

How to Fix It

1. 1

   Force close and reopen the app

   Go to Android Settings, then Apps, then BP Pulse. Tap 'Force Stop,' wait a few seconds, then open the app again.

2. 2

   Clear the app cache

   In Settings, go to Apps, then BP Pulse, then Storage, then 'Clear Cache.' This removes temporary data without deleting your account. You will not need to log in again.

3. 3

   Check for an app update

   Open the Google Play Store, search for BP Pulse, and tap 'Update' if available. Crashes often follow a buggy release that gets patched within days.

4. 4

   Use contactless payment as a backup

   If the app will not cooperate, tap your bank card on the charger's contactless reader to start a session without the app.

5. 5

   Reinstall the app if crashes persist

   Uninstall BP Pulse, restart your phone, then reinstall from the Play Store. You will need to log in again, so make sure you know your BP Pulse account email.

Charger shows 'Out of Service' with no visible damage

The screen displays 'Out of Service' or 'Unavailable,' but the charger looks perfectly fine. No broken cables, no barrier tape, no obvious reason it should be offline.

Symptoms

• Screen stuck on 'Out of Service' message
• Charger appears available in the app but shows error on arrival
• Status light is red or off entirely
• Other chargers at the same location work fine

How to Fix It

1. 1

   Check the BP Pulse app for real-time status

   Open the app and look at this specific charger. If it shows as unavailable there too, the network has flagged it remotely. A maintenance team likely already knows.

2. 2

   Look for a reset button or power switch

   Some older BP Pulse units (especially former Chargemaster ones) have a small reset button behind a panel or near the base. Pressing it can sometimes clear a stuck error state.

3. 3

   Report it in the app

   Use the 'Report a problem' option on the charger's detail page in the BP Pulse app. This helps BP Pulse prioritize repairs and updates the status for other drivers.

4. 4

   Move to another charger

   An 'Out of Service' state usually means a backend fault, a communication issue with the network, or a pending software update. You cannot fix these yourself. Use another unit or location.

Charging session drops after 5-10 minutes

Charging starts normally, but the session ends on its own after a few minutes. Your car shows it is no longer receiving power, and the charger returns to the welcome screen.

Symptoms

• Car dashboard shows charging stopped unexpectedly
• Charger screen returns to 'Plug in to start' after a few minutes
• You receive a session-ended notification in the app with a very short session
• This happens repeatedly at the same charger

How to Fix It

1. 1

   Check the connector is fully seated

   Unplug the cable, inspect the connector pins for dirt or debris, and plug it back in firmly until you hear a click. A loose connection can cause the charger to drop the session.

2. 2

   Check your car's charge limit

   If your car's charge limit is set very close to the current battery level, some vehicles will stop charging almost immediately. Set the limit to 80% or higher and try again.

3. 3

   Try the other connector type

   If the charger offers both CCS2 and CHAdeMO and your car supports CCS2, make sure you are using CCS2. Using the wrong connector obviously will not fit, but a worn CCS2 connector on one side may work better on the other unit.

4. 4

   Start a new session at a different unit

   Repeated drops at the same charger point to a hardware fault on that unit. Move to another charger and try again.

5. 5

   Report the faulty unit

   Note the charger ID (printed on the unit) and report it via the BP Pulse app or call the BP Pulse support number shown on the charger. This helps get the unit serviced.

Subscription vs pay-as-you-go pricing confusion

BP Pulse offers a subscription plan with lower per-kWh rates and a pay-as-you-go option with higher rates. It is not always clear which pricing you are on, or whether the subscription is worth it for your usage.

Symptoms

• Charged a higher rate than expected on your receipt
• Unsure whether your subscription is active
• Signed up for subscription but still seeing non-member prices
• Cannot figure out how to switch between plans

How to Fix It

1. 1

   Check your plan status in the app

   Open the BP Pulse app, go to your account settings, and look for your subscription status. If it says 'Active,' you should be getting the lower rate automatically.

2. 2

   Make sure you are starting sessions through the app

   Subscription pricing only applies when you start the session via the BP Pulse app or RFID card linked to your account. Tapping a contactless bank card will charge you the standard pay-as-you-go rate.

3. 3

   Review your charging history for rate discrepancies

   In the app, go to Charging History and check the per-kWh rate on recent sessions. Compare this to the subscription rate listed on the BP Pulse pricing page.

4. 4

   Cancel or change your plan if needed

   You can manage your subscription in the app under Account, then Subscription. If you charge infrequently, pay-as-you-go may actually cost less overall despite the higher per-kWh rate.