Maxus eDeliver 3 Charging at Tesla Supercharger

Maxus eDeliver 3 Charger Will Not Start Charging

You plugged in the CCS2 cable and nothing happened. Or the charger keeps showing an error. The eDeliver 3 is a solid delivery van, but as a less common brand in Europe, it can occasionally encounter compatibility issues with certain chargers. Most start failures come down to authentication, cable seating, or charger compatibility.

Symptoms

• CCS2 connector plugged in but charger shows no active session
• Charger displays an error code immediately after connecting
• Dashboard shows the charge port is connected but charging does not begin
• Cable does not lock into the CCS2 port on the eDeliver 3
• Charger starts the handshake but fails with a protocol error

What to Do

1. 1

   Remove and reseat the CCS2 connector

   Pull the connector out completely, wait 10 seconds, and push it back in firmly. Make sure it clicks and locks. Check the charge port for debris.

2. 2

   Turn the vehicle off and on

   Switch the eDeliver 3 fully off, wait 30 seconds, then turn it back on. Unplug and replug the cable. This resets the charging communication system.

3. 3

   Re-authenticate with the charger

   Cancel any active session in your charging app and start fresh. If using RFID, hold the card against the reader for a few seconds. Try authenticating before you plug in if the charger supports that flow.

4. 4

   Try a different charger brand

   If the eDeliver 3 will not start on this charger, try a different brand of charger. The eDeliver 3 may have better compatibility with some charger manufacturers. Note which ones work for future reference.

5. 5

   Check for software updates

   Contact your Maxus dealer or check the Maxus app. Software updates can fix charging compatibility issues. The Maxus service network in Europe is smaller, so plan service visits ahead of time.

6. 6

   Contact Maxus support

   If the eDeliver 3 consistently fails to start on multiple chargers, there may be a vehicle-side issue. Contact your Maxus dealer. Keep a log of which chargers failed and any error codes displayed.

Maxus eDeliver 3 Charging Payment Failed at DC

The charger is right there, your eDeliver 3 needs a charge, and the payment just failed. Payment issues at public chargers have nothing to do with your van. They are about the charging network, your card, or your phone signal. Here is how to get around it and get charging.

Symptoms

• Charger displays a payment error or 'transaction declined' message
• Charging app shows 'session failed to start' after payment attempt
• RFID card is not recognized by the charger reader
• Contactless bank card tap does not register
• Authorization starts but times out before the charger delivers power

What to Do

1. 1

   Try a different payment method

   Switch from RFID to app or from app to contactless bank card. Always carry at least two options so one failure does not leave you stranded.

2. 2

   Check your mobile signal

   If signal is weak, the app cannot complete the transaction. Step away from walls or structures and try again.

3. 3

   Verify your payment details

   Open the charging app and check that your card is valid and up to date. Update if the card has been replaced.

4. 4

   Check accepted networks on the charger

   Look for logos showing which networks and apps work at this charger. If yours is not listed, you need a different payment method or a different charger.

5. 5

   Contact your fleet manager

   If using a company RFID card that is not working, your manager can check if the card is active and has no restrictions. Most RFID cards have a support number printed on them.

6. 6

   Find a nearby alternative charger

   If payment is not working here, check your app for the next closest charger on your route. Move on rather than losing delivery time.

Maxus eDeliver 3 Charging Slower Than Expected

You stopped at a public charger expecting a quick top-up and the charger shows 15 kW instead of the 90 kW maximum. The eDeliver 3's 52.5 kWh battery can reach up to 90 kW on DC, but the actual speed depends on temperature, state of charge, and the charger. As a less common brand in Europe, the eDeliver 3 may also encounter occasional charger compatibility quirks. Here is what to check.

Symptoms

• DC fast charging speed well below the 90 kW maximum
• AC charging stuck at about 3 kW instead of the 7 kW maximum
• Charging speed drops sharply after reaching 50-60% on the dashboard
• Charging starts at a reasonable speed but slows down within minutes
• Charger display shows lower power than its rated output

What to Do

1. 1

   Check the battery temperature

   Look at the dashboard for battery temperature information. If the battery is cold, driving for 20-30 minutes before charging can help. The eDeliver 3 lacks preconditioning, so the battery warms up only through driving.

2. 2

   Check your state of charge

   Look at the battery percentage on the dashboard. If you are above 80%, the slower speed is normal. Arrive between 10-20% for the fastest DC charging speeds.

3. 3

   Verify the charger is not sharing power

   Look at the charger. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

4. 4

   Try a different charger brand

   If speeds are consistently low at one type of charger, try a different brand or network. The eDeliver 3 may work better with some charger manufacturers than others due to its less common charging firmware.

5. 5

   Check for vehicle software updates

   Contact your Maxus dealer or check the Maxus app for available software updates. Updates can improve charging compatibility and speeds. The Maxus service network is smaller, so this may require scheduling ahead.

6. 6

   Accept the AC limitation

   If your depot wallbox delivers 7 kW or less, you are already at the eDeliver 3's maximum AC rate. A 3-phase 11 kW or 22 kW wallbox will not charge faster than 7 kW on this van. Plan overnight charging accordingly.

Non-Tesla vehicle cannot find the station in the Tesla app

You arrive at a Supercharger with your non-Tesla EV but the station does not appear in the Tesla app, or it shows as Tesla-only.

Symptoms

• Tesla app shows the station but does not list it as open to other brands
• Station appears on the map but the 'Start Charging' button is grayed out
• App says 'This location is not available for your vehicle'
• You can see other non-Tesla vehicles charging but the app will not let you start

How to Fix It

1. 1

   Confirm the station is open to non-Tesla vehicles

   Not all Supercharger locations are open to other brands. In the Tesla app, look for stations marked with a label indicating non-Tesla access. If there is no such label, the station is Tesla-only.

2. 2

   Update the Tesla app

   Tesla frequently adds new non-Tesla locations. If your app is outdated, recently opened stations may not appear as accessible. Update to the latest version.

3. 3

   Check your Tesla account setup

   You need a Tesla account with a valid payment method added, even if you do not own a Tesla. Open the app, go to your account settings, and confirm a credit or debit card is saved.

4. 4

   Try selecting the specific stall number

   After plugging in, open the Tesla app, select the station, and tap the stall number that matches the one you plugged into. The stall number is printed on the charger post.

5. 5

   Restart the Tesla app

   Force-close and reopen the app. Location and station data sometimes fails to load correctly on the first attempt.

Payment hold is larger than expected

Tesla places a pre-authorization hold on your payment method when you start a Supercharger session. This hold can be surprisingly large and may temporarily reduce your available balance.

Symptoms

• Bank notification shows a hold of 50 to 120 EUR before charging begins
• Available balance on your debit card drops significantly
• Multiple holds appear from previous sessions that have not been released yet
• Hold amount does not match the actual charging cost

How to Fix It

1. 1

   Understand that holds are temporary

   Tesla pre-authorizes a fixed amount to ensure payment. The actual charge replaces the hold once the session is complete. The hold typically releases within 1 to 5 business days depending on your bank.

2. 2

   Use a credit card instead of a debit card

   Credit cards handle pre-authorization holds without affecting your available cash balance. Debit cards temporarily lock the held amount from your account.

3. 3

   Check the Tesla app for final session cost

   After charging, the Tesla app shows the actual amount you will be billed. This is always less than or equal to the pre-authorization hold.

4. 4

   Contact your bank if holds persist beyond 7 days

   If a hold has not been released after a week, contact your bank and provide the transaction reference from the Tesla app. Banks can manually release stale holds.

Session ends early or stops unexpectedly

Charging stops before reaching your target battery level. The car disconnects or the Supercharger stops delivering power mid-session.

Symptoms

• Charging stops at 80% even though you set a higher limit
• Session ends after a few minutes with no error message
• Car shows 'Charging interrupted' or 'Check charge cable'
• Supercharger light turns from green to red or flashing

How to Fix It

1. 1

   Check your charge limit setting

   Tesla vehicles default to an 80% charge limit. Non-Tesla vehicles have their own limit settings in the infotainment system. Verify you have set the limit above where charging stopped.

2. 2

   Reseat the cable connector

   Unplug the cable, inspect the connector and your vehicle's charge port for debris, and plug it back in firmly. A loose connection can cause the session to drop.

3. 3

   Try a different stall

   Individual Supercharger stalls can have intermittent faults. Move to another stall, preferably one that is not paired with an active session (stalls sharing a power cabinet are usually labeled with paired numbers like 1A/1B).

4. 4

   Check for idle fees

   If you reached your charge limit and did not unplug promptly, Tesla may have ended the session and started idle fees. Check the Tesla app for notifications.

5. 5

   Restart your vehicle

   For non-Tesla vehicles, turn the car off completely, wait 30 seconds, and turn it back on. Then plug in again. Some vehicles need a restart to clear communication errors with the Supercharger.

Reduced charging speed due to power sharing

Your charging speed is significantly lower than the station's advertised maximum. This often happens because Supercharger stalls share power with a paired stall.

Symptoms

• Charging at 60 to 80 kW at a station rated for 250 kW
• Speed dropped when another vehicle plugged in at a nearby stall
• Speed is much lower than you got at the same station previously
• One stall charges fast while the paired stall is very slow

How to Fix It

1. 1

   Move to an unpaired stall

   Tesla Supercharger stalls are paired (for example, 1A and 1B share a power cabinet). If someone is using 1A, stall 1B will be slower. Choose a stall where neither paired unit is occupied.

2. 2

   Look at the stall labels

   Paired stalls usually share a number with A/B suffixes, or are directly adjacent. At V3 Superchargers (250 kW), power sharing is less of an issue than at older V2 stations (150 kW).

3. 3

   Check your battery temperature

   Tesla vehicles precondition the battery automatically when navigating to a Supercharger. If you did not use Tesla navigation (or you drive a non-Tesla), the battery may be cold and limiting charge speed on its own.

4. 4

   Arrive with a lower state of charge

   Charging speed decreases as the battery fills. For the fastest stop, arrive between 5 and 20% if you can do so safely. The difference in charge speed between arriving at 10% versus 40% is significant.

Non-Tesla vehicle CCS2 connector issues

At Supercharger stations open to non-Tesla vehicles, the CCS2 connector may not work correctly with your car. In Europe, open Supercharger stations have native CCS2 cables, so no adapter is needed.

Symptoms

• The CCS2 connector does not lock into your vehicle's charge port
• Session starts but drops after a few seconds
• Tesla app does not recognize your vehicle after plugging in
• The connector fits but no power is delivered

How to Fix It

1. 1

   Make sure you are using the CCS2 cable, not the Tesla connector

   Open Supercharger stations in Europe have separate CCS2 cables alongside Tesla connectors, or dedicated CCS2 posts. Use the CCS2 cable for non-Tesla vehicles.

2. 2

   Push the connector in firmly until it clicks

   CCS2 connectors need a firm push to fully seat and lock. If the connector is loose, the charger cannot communicate with your vehicle.

3. 3

   Start the session through the Tesla app

   Select the correct stall number in the Tesla app and start the session. The stall number is printed on the charger post. It must match exactly.

4. 4

   Try a different stall

   Individual stalls can have faulty connectors. Move to another stall, preferably one that is not paired with an active session.

5. 5

   Check vehicle compatibility

   Not all non-Tesla vehicles work perfectly at every Supercharger station. If your vehicle repeatedly fails to connect, check Tesla's website or app for your vehicle's compatibility status.