Maxus eDeliver 3 Charging at Recharge

Maxus eDeliver 3 Charger Will Not Start Charging

You plugged in the CCS2 cable and nothing happened. Or the charger keeps showing an error. The eDeliver 3 is a solid delivery van, but as a less common brand in Europe, it can occasionally encounter compatibility issues with certain chargers. Most start failures come down to authentication, cable seating, or charger compatibility.

Symptoms

• CCS2 connector plugged in but charger shows no active session
• Charger displays an error code immediately after connecting
• Dashboard shows the charge port is connected but charging does not begin
• Cable does not lock into the CCS2 port on the eDeliver 3
• Charger starts the handshake but fails with a protocol error

What to Do

1. 1

   Remove and reseat the CCS2 connector

   Pull the connector out completely, wait 10 seconds, and push it back in firmly. Make sure it clicks and locks. Check the charge port for debris.

2. 2

   Turn the vehicle off and on

   Switch the eDeliver 3 fully off, wait 30 seconds, then turn it back on. Unplug and replug the cable. This resets the charging communication system.

3. 3

   Re-authenticate with the charger

   Cancel any active session in your charging app and start fresh. If using RFID, hold the card against the reader for a few seconds. Try authenticating before you plug in if the charger supports that flow.

4. 4

   Try a different charger brand

   If the eDeliver 3 will not start on this charger, try a different brand of charger. The eDeliver 3 may have better compatibility with some charger manufacturers. Note which ones work for future reference.

5. 5

   Check for software updates

   Contact your Maxus dealer or check the Maxus app. Software updates can fix charging compatibility issues. The Maxus service network in Europe is smaller, so plan service visits ahead of time.

6. 6

   Contact Maxus support

   If the eDeliver 3 consistently fails to start on multiple chargers, there may be a vehicle-side issue. Contact your Maxus dealer. Keep a log of which chargers failed and any error codes displayed.

Maxus eDeliver 3 Charging Payment Failed at DC

The charger is right there, your eDeliver 3 needs a charge, and the payment just failed. Payment issues at public chargers have nothing to do with your van. They are about the charging network, your card, or your phone signal. Here is how to get around it and get charging.

Symptoms

• Charger displays a payment error or 'transaction declined' message
• Charging app shows 'session failed to start' after payment attempt
• RFID card is not recognized by the charger reader
• Contactless bank card tap does not register
• Authorization starts but times out before the charger delivers power

What to Do

1. 1

   Try a different payment method

   Switch from RFID to app or from app to contactless bank card. Always carry at least two options so one failure does not leave you stranded.

2. 2

   Check your mobile signal

   If signal is weak, the app cannot complete the transaction. Step away from walls or structures and try again.

3. 3

   Verify your payment details

   Open the charging app and check that your card is valid and up to date. Update if the card has been replaced.

4. 4

   Check accepted networks on the charger

   Look for logos showing which networks and apps work at this charger. If yours is not listed, you need a different payment method or a different charger.

5. 5

   Contact your fleet manager

   If using a company RFID card that is not working, your manager can check if the card is active and has no restrictions. Most RFID cards have a support number printed on them.

6. 6

   Find a nearby alternative charger

   If payment is not working here, check your app for the next closest charger on your route. Move on rather than losing delivery time.

Maxus eDeliver 3 Charging Slower Than Expected

You stopped at a public charger expecting a quick top-up and the charger shows 15 kW instead of the 90 kW maximum. The eDeliver 3's 52.5 kWh battery can reach up to 90 kW on DC, but the actual speed depends on temperature, state of charge, and the charger. As a less common brand in Europe, the eDeliver 3 may also encounter occasional charger compatibility quirks. Here is what to check.

Symptoms

• DC fast charging speed well below the 90 kW maximum
• AC charging stuck at about 3 kW instead of the 7 kW maximum
• Charging speed drops sharply after reaching 50-60% on the dashboard
• Charging starts at a reasonable speed but slows down within minutes
• Charger display shows lower power than its rated output

What to Do

1. 1

   Check the battery temperature

   Look at the dashboard for battery temperature information. If the battery is cold, driving for 20-30 minutes before charging can help. The eDeliver 3 lacks preconditioning, so the battery warms up only through driving.

2. 2

   Check your state of charge

   Look at the battery percentage on the dashboard. If you are above 80%, the slower speed is normal. Arrive between 10-20% for the fastest DC charging speeds.

3. 3

   Verify the charger is not sharing power

   Look at the charger. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

4. 4

   Try a different charger brand

   If speeds are consistently low at one type of charger, try a different brand or network. The eDeliver 3 may work better with some charger manufacturers than others due to its less common charging firmware.

5. 5

   Check for vehicle software updates

   Contact your Maxus dealer or check the Maxus app for available software updates. Updates can improve charging compatibility and speeds. The Maxus service network is smaller, so this may require scheduling ahead.

6. 6

   Accept the AC limitation

   If your depot wallbox delivers 7 kW or less, you are already at the eDeliver 3's maximum AC rate. A 3-phase 11 kW or 22 kW wallbox will not charge faster than 7 kW on this van. Plan overnight charging accordingly.

Charger stuck in "preparing" state

You authenticated successfully, the charger says "preparing," but it never starts delivering power. This is one of the most reported issues on Recharge stations, especially at older units.

Symptoms

• Charger screen shows "Preparing" or "Initializing" for more than two minutes
• Your car's charging indicator does not activate
• The Recharge app shows the session as active but 0 kW delivered
• The charger fan spins up but no power flows

How to Fix It

1. 1

   Wait up to three minutes

   Some Recharge units, particularly the 300kW stations, take longer to complete the power handshake with your car. Give it a full three minutes before taking action.

2. 2

   Unplug and reconnect

   Remove the CCS2 connector, wait 15 seconds, then plug it back in firmly. This resets the communication between your car and the charger.

3. 3

   Stop the session in the Recharge app and start a new one

   Open the Recharge app, tap Stop on the active session, wait for it to fully end, then start a new session on the same charger. This clears any stuck state on the backend.

4. 4

   Try the other connector on the same unit

   Many Recharge stations have two CCS2 connectors. If one is stuck, the other connector on the same unit often works fine.

5. 5

   Use a different authentication method

   If you started with the app, try your RFID card instead, or vice versa. Sometimes the issue is with the authentication path, not the charger hardware.

Old Fortum branding causes app scan failure

Recharge was originally part of Fortum's charging operations before being spun off as a separate company. Some older stations still display Fortum logos and QR codes. Scanning an old Fortum QR code with the Recharge app may not work, or it may redirect to a dead Fortum page.

Symptoms

• QR code on the charger opens a Fortum website or shows an error
• Recharge app says "Charger not found" after scanning
• Station ID on the physical unit does not match what the Recharge app expects
• The charger has Fortum branding but is listed as Recharge in third-party apps

How to Fix It

1. 1

   Ignore the QR code and search by station name in the Recharge app

   Open the Recharge app, use the map or search to find the station by location. The charger will appear under its Recharge name even if the physical unit still says Fortum.

2. 2

   Enter the charger ID manually

   Look for a numeric ID on the charger, often printed on a sticker near the connector. In the Recharge app, tap "Enter ID" and type it in directly.

3. 3

   Use RFID or contactless payment instead of the app

   Tap your Recharge RFID card or a contactless bank card on the reader. This bypasses the app entirely and works regardless of the branding on the charger.

4. 4

   Check if contactless is available on this unit

   Not all Recharge stations support contactless bank card payment. Look for a card reader terminal on the charger. If there is no terminal, you will need the app or an RFID card.

RFID card from old Fortum account not recognized

If you had a Fortum Charge & Drive account and RFID card, it may not work automatically on the Recharge network. Some cards were migrated, others were not.

Symptoms

• Tapping your old Fortum RFID card shows "Card not recognized" on the charger
• The charger beeps but does not start a session
• Your Fortum card works on some stations but not others

How to Fix It

1. 1

   Log in to the Recharge app and check your RFID cards

   Open the Recharge app, go to your account settings, and look under RFID cards. If your old Fortum card is not listed, it was not migrated automatically.

2. 2

   Re-register your RFID card

   In the Recharge app, tap "Add RFID card" and follow the steps. You will need the card number printed on the back of your RFID card.

3. 3

   Use the app to start the session while you wait for RFID activation

   RFID card registration can take up to 24 hours to propagate across all stations. Use the app to authenticate in the meantime.

4. 4

   Order a new Recharge RFID card if re-registration fails

   Some older Fortum cards use a chip format that is not compatible. You can order a new Recharge RFID card through the app or website.

Contactless payment not accepted

You are trying to tap your bank card or phone to pay, but the charger does not respond or shows an error. Contactless payment availability varies across Recharge stations.

Symptoms

• No card reader terminal visible on the charger
• Card reader shows "Payment failed" or does not respond to taps
• Apple Pay or Google Pay not recognized
• The charger prompts for an RFID card but you only have a bank card

How to Fix It

1. 1

   Check if this station supports contactless payment

   Look for a separate payment terminal with a contactless symbol. Not all Recharge stations have been upgraded. The Recharge app shows payment options for each station on the station detail page.

2. 2

   Try removing and re-holding your card

   Hold your card flat against the reader for at least three seconds. Some terminals need a longer hold than you might expect. Remove the card fully, then try again.

3. 3

   Fall back to the Recharge app

   If contactless is not working, open the Recharge app and start the session from there. You need a payment method saved in the app.

4. 4

   Try a different card

   Some Visa Electron and certain prepaid cards are not accepted by the payment terminals. A standard Visa or Mastercard debit or credit card usually works.

Charging speed much lower than expected

The station is rated for 300kW, but your car is only pulling 50kW or less. While your car's battery management limits the maximum speed, Recharge stations can also throttle power.

Symptoms

• Charger display shows far less power than the station's rated capacity
• Charging speed drops suddenly mid-session
• Other cars at the same station are also charging slowly
• The Recharge app shows the session but at low power

How to Fix It

1. 1

   Check how many other cars are charging at the same station

   Recharge stations with multiple connectors often share a power cabinet. If two or three cars are charging simultaneously, the available power per car drops. This is normal and not a fault.

2. 2

   Check your battery level

   DC fast charging slows significantly above 80% on most EVs. If your battery is above 70-80%, the slower speed is your car protecting the battery, not a problem with the Recharge station.

3. 3

   Check the temperature

   In cold weather, your car may limit charging speed until the battery warms up. This can take 10-15 minutes of charging before speeds increase. Some cars precondition the battery if you set the charger as a destination in navigation.

4. 4

   Try a different connector at the station

   Individual connectors can have faults that limit power output. If another connector is free, unplug and try it.

5. 5

   Report the issue in the Recharge app

   If the speed is unusually low and none of the above apply, report it through the Recharge app. Tap the active session and look for a "Report issue" option. This helps Recharge identify hardware problems.