Mercedes eVito Charging at Recharge

Mercedes eVito Van Charger Will Not Start a Session

You have connected the charger to your Mercedes eVito and nothing is happening. No session, no power, no charging light. When you are between jobs or trying to charge at the depot, you need this resolved quickly. Here is how.

Symptoms

• CCS2 or Type 2 connector is plugged in but no session starts
• The MBUX display does not show charging activity
• The charger screen shows an error after plug-in
• The charge port indicator stays off or flashes amber
• The depot wallbox status light does not change when plugged in

What to Do

1. 1

   Authenticate before plugging in

   At public chargers, tap your RFID card or start the session in the app before inserting the connector. Wait for the charger to confirm it is ready.

2. 2

   Clean and reinsert the connector

   Remove the connector, wipe the charge port on the eVito with a dry cloth to remove any dirt, then reinsert the connector firmly until it clicks.

3. 3

   Check MBUX charging settings

   On the MBUX display, navigate to the charging menu. Check if departure time charging is active. Disable it for immediate charging.

4. 4

   Check the depot electrical panel

   If at the depot, check the circuit breaker for the charging circuit. Also check the wallbox status indicator. Report issues to your fleet manager.

5. 5

   Lock and unlock the van

   Use the key to lock the eVito, wait 20 seconds, then unlock. This can reset the charging electronics after a fault state.

6. 6

   Move to a different charger

   If the charger is faulty, do not waste time. Move to another unit or station, especially if you are mid-route.

Mercedes eVito Van Payment Failed at Charging Station

You are at a public charger with your Mercedes eVito and the payment will not go through. Whether it is a fleet card, personal RFID, or an app, payment failures at public chargers waste time between jobs. Here is how to resolve it fast.

Symptoms

• Fleet card does not start a session at the charger
• RFID card tap produces no response
• Charging app shows a payment authorization error
• Contactless bank card is declined
• Charger shows 'payment failed' on the screen

What to Do

1. 1

   Check accepted payment methods

   Look at the charger stickers and screen for accepted networks and cards. If your fleet card logo is not shown, this charger is not on your network.

2. 2

   Try a different payment method

   Switch between fleet card, personal RFID, charging app, and contactless bank card. One may work where others fail.

3. 3

   Verify fleet card status

   Contact your fleet manager or check the fleet card provider app to confirm the card is active and has not hit a spending limit.

4. 4

   Hold the card steadily

   Place the card flat against the reader for 3 seconds. Do not tap and pull away quickly. Gloves can interfere with NFC reading.

5. 5

   Cancel and retry

   Cancel any pending session in the app, wait 60 seconds, and start a fresh attempt.

6. 6

   Move to another charger unit

   If the payment reader on this unit is broken, try the next charger at the station. Do not waste time troubleshooting hardware you cannot fix.

Mercedes eVito Van Charging Slower Than Expected Speed

Your Mercedes eVito is charging slower than the 110 kW DC maximum. Or your depot wallbox is barely delivering power overnight. Without battery preconditioning, the eVito is especially sensitive to cold weather. Here is what to check and how to improve your charging speed.

Symptoms

• DC fast charging well below the 110 kW maximum
• Depot AC charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops quickly after 40-50% state of charge
• Winter charging starts extremely slowly
• Mid-route DC charging takes too long between jobs

What to Do

1. 1

   Drive before charging in cold weather

   Since the eVito lacks preconditioning, drive for at least 20-30 minutes before stopping at a DC charger in winter. This warms the battery through use.

2. 2

   Charge between 20-50% for fastest speeds

   Plan your mid-route charging stops to arrive between 20-50% state of charge. This is where the eVito can approach its 110 kW peak.

3. 3

   Check your depot charger wiring

   Ask your fleet manager or electrician to verify the depot wallbox is wired for three-phase at 16A per phase for 11 kW. Single-phase installations are common but much slower.

4. 4

   Choose unshared DC chargers

   At public stations, check if the charger is sharing power. If another vehicle is on the paired connector, try a different unit.

5. 5

   Use MBUX to check charging status

   The MBUX infotainment system shows current charging power and estimated time. Use this to verify speeds and decide if you should move to a different charger.

6. 6

   Try a different charger

   If speeds remain well below expected at a low state of charge, the charger may be faulty. Move to another unit.

Charger stuck in "preparing" state

You authenticated successfully, the charger says "preparing," but it never starts delivering power. This is one of the most reported issues on Recharge stations, especially at older units.

Symptoms

• Charger screen shows "Preparing" or "Initializing" for more than two minutes
• Your car's charging indicator does not activate
• The Recharge app shows the session as active but 0 kW delivered
• The charger fan spins up but no power flows

How to Fix It

1. 1

   Wait up to three minutes

   Some Recharge units, particularly the 300kW stations, take longer to complete the power handshake with your car. Give it a full three minutes before taking action.

2. 2

   Unplug and reconnect

   Remove the CCS2 connector, wait 15 seconds, then plug it back in firmly. This resets the communication between your car and the charger.

3. 3

   Stop the session in the Recharge app and start a new one

   Open the Recharge app, tap Stop on the active session, wait for it to fully end, then start a new session on the same charger. This clears any stuck state on the backend.

4. 4

   Try the other connector on the same unit

   Many Recharge stations have two CCS2 connectors. If one is stuck, the other connector on the same unit often works fine.

5. 5

   Use a different authentication method

   If you started with the app, try your RFID card instead, or vice versa. Sometimes the issue is with the authentication path, not the charger hardware.

Old Fortum branding causes app scan failure

Recharge was originally part of Fortum's charging operations before being spun off as a separate company. Some older stations still display Fortum logos and QR codes. Scanning an old Fortum QR code with the Recharge app may not work, or it may redirect to a dead Fortum page.

Symptoms

• QR code on the charger opens a Fortum website or shows an error
• Recharge app says "Charger not found" after scanning
• Station ID on the physical unit does not match what the Recharge app expects
• The charger has Fortum branding but is listed as Recharge in third-party apps

How to Fix It

1. 1

   Ignore the QR code and search by station name in the Recharge app

   Open the Recharge app, use the map or search to find the station by location. The charger will appear under its Recharge name even if the physical unit still says Fortum.

2. 2

   Enter the charger ID manually

   Look for a numeric ID on the charger, often printed on a sticker near the connector. In the Recharge app, tap "Enter ID" and type it in directly.

3. 3

   Use RFID or contactless payment instead of the app

   Tap your Recharge RFID card or a contactless bank card on the reader. This bypasses the app entirely and works regardless of the branding on the charger.

4. 4

   Check if contactless is available on this unit

   Not all Recharge stations support contactless bank card payment. Look for a card reader terminal on the charger. If there is no terminal, you will need the app or an RFID card.

RFID card from old Fortum account not recognized

If you had a Fortum Charge & Drive account and RFID card, it may not work automatically on the Recharge network. Some cards were migrated, others were not.

Symptoms

• Tapping your old Fortum RFID card shows "Card not recognized" on the charger
• The charger beeps but does not start a session
• Your Fortum card works on some stations but not others

How to Fix It

1. 1

   Log in to the Recharge app and check your RFID cards

   Open the Recharge app, go to your account settings, and look under RFID cards. If your old Fortum card is not listed, it was not migrated automatically.

2. 2

   Re-register your RFID card

   In the Recharge app, tap "Add RFID card" and follow the steps. You will need the card number printed on the back of your RFID card.

3. 3

   Use the app to start the session while you wait for RFID activation

   RFID card registration can take up to 24 hours to propagate across all stations. Use the app to authenticate in the meantime.

4. 4

   Order a new Recharge RFID card if re-registration fails

   Some older Fortum cards use a chip format that is not compatible. You can order a new Recharge RFID card through the app or website.

Contactless payment not accepted

You are trying to tap your bank card or phone to pay, but the charger does not respond or shows an error. Contactless payment availability varies across Recharge stations.

Symptoms

• No card reader terminal visible on the charger
• Card reader shows "Payment failed" or does not respond to taps
• Apple Pay or Google Pay not recognized
• The charger prompts for an RFID card but you only have a bank card

How to Fix It

1. 1

   Check if this station supports contactless payment

   Look for a separate payment terminal with a contactless symbol. Not all Recharge stations have been upgraded. The Recharge app shows payment options for each station on the station detail page.

2. 2

   Try removing and re-holding your card

   Hold your card flat against the reader for at least three seconds. Some terminals need a longer hold than you might expect. Remove the card fully, then try again.

3. 3

   Fall back to the Recharge app

   If contactless is not working, open the Recharge app and start the session from there. You need a payment method saved in the app.

4. 4

   Try a different card

   Some Visa Electron and certain prepaid cards are not accepted by the payment terminals. A standard Visa or Mastercard debit or credit card usually works.

Charging speed much lower than expected

The station is rated for 300kW, but your car is only pulling 50kW or less. While your car's battery management limits the maximum speed, Recharge stations can also throttle power.

Symptoms

• Charger display shows far less power than the station's rated capacity
• Charging speed drops suddenly mid-session
• Other cars at the same station are also charging slowly
• The Recharge app shows the session but at low power

How to Fix It

1. 1

   Check how many other cars are charging at the same station

   Recharge stations with multiple connectors often share a power cabinet. If two or three cars are charging simultaneously, the available power per car drops. This is normal and not a fault.

2. 2

   Check your battery level

   DC fast charging slows significantly above 80% on most EVs. If your battery is above 70-80%, the slower speed is your car protecting the battery, not a problem with the Recharge station.

3. 3

   Check the temperature

   In cold weather, your car may limit charging speed until the battery warms up. This can take 10-15 minutes of charging before speeds increase. Some cars precondition the battery if you set the charger as a destination in navigation.

4. 4

   Try a different connector at the station

   Individual connectors can have faults that limit power output. If another connector is free, unplug and try it.

5. 5

   Report the issue in the Recharge app

   If the speed is unusually low and none of the above apply, report it through the Recharge app. Tap the active session and look for a "Report issue" option. This helps Recharge identify hardware problems.