Maxus eDeliver 3 Charging at Mer

Maxus eDeliver 3 Charger Will Not Start Charging

You plugged in the CCS2 cable and nothing happened. Or the charger keeps showing an error. The eDeliver 3 is a solid delivery van, but as a less common brand in Europe, it can occasionally encounter compatibility issues with certain chargers. Most start failures come down to authentication, cable seating, or charger compatibility.

Symptoms

• CCS2 connector plugged in but charger shows no active session
• Charger displays an error code immediately after connecting
• Dashboard shows the charge port is connected but charging does not begin
• Cable does not lock into the CCS2 port on the eDeliver 3
• Charger starts the handshake but fails with a protocol error

What to Do

1. 1

   Remove and reseat the CCS2 connector

   Pull the connector out completely, wait 10 seconds, and push it back in firmly. Make sure it clicks and locks. Check the charge port for debris.

2. 2

   Turn the vehicle off and on

   Switch the eDeliver 3 fully off, wait 30 seconds, then turn it back on. Unplug and replug the cable. This resets the charging communication system.

3. 3

   Re-authenticate with the charger

   Cancel any active session in your charging app and start fresh. If using RFID, hold the card against the reader for a few seconds. Try authenticating before you plug in if the charger supports that flow.

4. 4

   Try a different charger brand

   If the eDeliver 3 will not start on this charger, try a different brand of charger. The eDeliver 3 may have better compatibility with some charger manufacturers. Note which ones work for future reference.

5. 5

   Check for software updates

   Contact your Maxus dealer or check the Maxus app. Software updates can fix charging compatibility issues. The Maxus service network in Europe is smaller, so plan service visits ahead of time.

6. 6

   Contact Maxus support

   If the eDeliver 3 consistently fails to start on multiple chargers, there may be a vehicle-side issue. Contact your Maxus dealer. Keep a log of which chargers failed and any error codes displayed.

Maxus eDeliver 3 Charging Payment Failed at DC

The charger is right there, your eDeliver 3 needs a charge, and the payment just failed. Payment issues at public chargers have nothing to do with your van. They are about the charging network, your card, or your phone signal. Here is how to get around it and get charging.

Symptoms

• Charger displays a payment error or 'transaction declined' message
• Charging app shows 'session failed to start' after payment attempt
• RFID card is not recognized by the charger reader
• Contactless bank card tap does not register
• Authorization starts but times out before the charger delivers power

What to Do

1. 1

   Try a different payment method

   Switch from RFID to app or from app to contactless bank card. Always carry at least two options so one failure does not leave you stranded.

2. 2

   Check your mobile signal

   If signal is weak, the app cannot complete the transaction. Step away from walls or structures and try again.

3. 3

   Verify your payment details

   Open the charging app and check that your card is valid and up to date. Update if the card has been replaced.

4. 4

   Check accepted networks on the charger

   Look for logos showing which networks and apps work at this charger. If yours is not listed, you need a different payment method or a different charger.

5. 5

   Contact your fleet manager

   If using a company RFID card that is not working, your manager can check if the card is active and has no restrictions. Most RFID cards have a support number printed on them.

6. 6

   Find a nearby alternative charger

   If payment is not working here, check your app for the next closest charger on your route. Move on rather than losing delivery time.

Maxus eDeliver 3 Charging Slower Than Expected

You stopped at a public charger expecting a quick top-up and the charger shows 15 kW instead of the 90 kW maximum. The eDeliver 3's 52.5 kWh battery can reach up to 90 kW on DC, but the actual speed depends on temperature, state of charge, and the charger. As a less common brand in Europe, the eDeliver 3 may also encounter occasional charger compatibility quirks. Here is what to check.

Symptoms

• DC fast charging speed well below the 90 kW maximum
• AC charging stuck at about 3 kW instead of the 7 kW maximum
• Charging speed drops sharply after reaching 50-60% on the dashboard
• Charging starts at a reasonable speed but slows down within minutes
• Charger display shows lower power than its rated output

What to Do

1. 1

   Check the battery temperature

   Look at the dashboard for battery temperature information. If the battery is cold, driving for 20-30 minutes before charging can help. The eDeliver 3 lacks preconditioning, so the battery warms up only through driving.

2. 2

   Check your state of charge

   Look at the battery percentage on the dashboard. If you are above 80%, the slower speed is normal. Arrive between 10-20% for the fastest DC charging speeds.

3. 3

   Verify the charger is not sharing power

   Look at the charger. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

4. 4

   Try a different charger brand

   If speeds are consistently low at one type of charger, try a different brand or network. The eDeliver 3 may work better with some charger manufacturers than others due to its less common charging firmware.

5. 5

   Check for vehicle software updates

   Contact your Maxus dealer or check the Maxus app for available software updates. Updates can improve charging compatibility and speeds. The Maxus service network is smaller, so this may require scheduling ahead.

6. 6

   Accept the AC limitation

   If your depot wallbox delivers 7 kW or less, you are already at the eDeliver 3's maximum AC rate. A 3-phase 11 kW or 22 kW wallbox will not charge faster than 7 kW on this van. Plan overnight charging accordingly.

Station occupancy not updating in the app

The Mer app shows a station as available, but when you arrive, all connectors are occupied or out of service. The real-time status in the app can lag behind by several minutes.

Symptoms

• App shows "Available" but all connectors are in use when you arrive
• App shows a station as occupied but the chargers are visibly free
• Connector status flickers between available and occupied in the app
• Recently freed connectors still show as "In use" in the app for several minutes

How to Fix It

1. 1

   Pull to refresh the station detail in the Mer app

   On the station page, pull down to force a status refresh. The app does not always update automatically, and a manual refresh often shows the correct status.

2. 2

   Close and reopen the app

   Force-close the Mer app and reopen it. This clears any cached station data and pulls a fresh status from the server.

3. 3

   Check a third-party app for a second opinion

   Apps like Plugsurfing, A Better Route Planner, or Google Maps sometimes pull fresher data from Mer's backend. Use one of these to verify availability if the Mer app seems wrong.

4. 4

   Drive to the station if it is nearby

   If the station is less than five minutes away, it is often faster to just go and check. Occupancy can change in the time it takes to troubleshoot the app.

Third-party RFID card rejected

You are trying to authenticate with an RFID card from a roaming provider like Plugsurfing, NewMotion, or Virta, but the Mer charger rejects it. Not all third-party RFID cards are accepted at every Mer station.

Symptoms

• Charger screen shows "Card not recognized" after tapping
• The charger beeps once but nothing happens
• Your RFID card works at other networks but fails at Mer
• The charger prompts you to try again but repeated taps do not help

How to Fix It

1. 1

   Hold the card flat against the reader for three full seconds

   Do not tap and remove quickly. Some Mer readers need a longer hold to register the card. Keep it pressed flat against the RFID symbol.

2. 2

   Check if your roaming provider covers Mer stations

   Open your roaming provider's app and search for this specific Mer station. Some providers have roaming agreements with Mer but not for every station type or region.

3. 3

   Use the Mer app instead

   Download the Mer app if you do not have it. Create an account and add a payment method. You can start the session through the app even if your RFID card does not work.

4. 4

   Try contactless bank card payment

   Newer Mer stations have a contactless payment terminal. Look for a card reader with the contactless payment symbol. Tap your bank card or phone to start.

5. 5

   Try a Mer-issued RFID card for future visits

   You can order an RFID card directly from Mer through their app or website. Mer's own cards are accepted at all Mer stations without roaming issues.

Charger screen showing error but no error code

The charger screen displays a generic error message like "Error" or "Fault" without any specific code or explanation. This makes it hard to know if the problem is temporary or if the unit is broken.

Symptoms

• Charger screen shows "Error" or a red warning icon with no further detail
• The error appears before you even try to authenticate
• The error appears after plugging in but before power delivery starts
• Screen alternates between the normal start screen and the error message

How to Fix It

1. 1

   Unplug the connector and wait 30 seconds

   Some Mer chargers show transient errors after a previous session ended abnormally. Unplugging and waiting gives the charger time to reset its internal state.

2. 2

   Try the other connector on the same unit

   If the station has a second CCS2 connector, try that one. A hardware fault on one connector does not always affect the other.

3. 3

   Check if other cars are successfully charging at the station

   If nobody at the station is charging, the entire station may be down. If others are charging fine, the issue is limited to your connector.

4. 4

   Report the faulty unit in the Mer app

   Open the Mer app, find the station, and report the issue. Include which connector number has the error. This helps Mer send a technician and warns other drivers.

5. 5

   Move to a different station

   A charger with a persistent generic error is unlikely to start working on its own. Use the Mer app to find the nearest alternative station.

Cable locked and will not release in cold weather

You finished charging but the CCS2 cable will not unlock from your car. In Nordic winters, ice can form around the connector locking mechanism, making it physically difficult to release.

Symptoms

• Pressing the connector release button does not unlock the cable
• The connector feels frozen in place
• Your car shows "Charging complete" but the cable is stuck
• The locking pin on the connector is visibly iced over

How to Fix It

1. 1

   Make sure the charging session has fully ended

   The cable stays locked while a session is active. Stop the session in the Mer app or on the charger screen, then try releasing the connector again. Wait 10 seconds after the session ends.

2. 2

   Try unlocking from your car

   Most EVs have a cable release option in the infotainment system or a button near the charge port. Use your car's unlock function rather than the connector button.

3. 3

   Warm the connector gently

   If ice is the problem, pour lukewarm water (not boiling) over the connector and charge port area. You can also cup your hands around the connector to warm it with body heat. Do not use force or tools to pry it free.

4. 4

   Run the car's cabin heater for a few minutes

   Turning on the car's climate system can gradually warm the charge port area from the inside. This works slowly but can free a mildly frozen connector after 5-10 minutes.

5. 5

   Call Mer support if the cable is truly stuck

   If nothing works after 15 minutes, call the support number on the charger. Mer can remotely release the cable lock on their end. Do not pull with excessive force as this can damage both the connector and your car's charge port.

App requires location services for remote start

The Mer app asks you to enable location services before you can start a charging session, even when you are standing right next to the charger and selected it manually from the map.

Symptoms

• App shows "Enable location services to start charging" popup
• Start button is grayed out until location permission is granted
• The app worked fine before but now demands location after an update
• You can browse the map but cannot start a session without GPS enabled

How to Fix It

1. 1

   Enable location services temporarily

   Go to your phone's settings, find the Mer app, and set location access to "While Using the App." You can change it back after your session.

2. 2

   Make sure GPS has a fix

   In underground parking garages or areas with poor GPS reception, the app may not be able to confirm your location. Step outside or move closer to an open area until the app detects your position.

3. 3

   Use RFID or contactless payment instead

   If you do not want to share your location, use your RFID card or a contactless bank card to start the session. These methods do not require the app at all.

4. 4

   Scan the QR code on the charger

   Some Mer chargers have a QR code that opens the start process in a browser, bypassing the app's location requirement.

Former Grønn Kontakt station not found in Mer app

Mer acquired Grønn Kontakt in Norway, but some older stations may not appear correctly in the Mer app, especially during the transition period.

Symptoms

• Station visible on the street but not on the Mer app map
• Searching by the old Grønn Kontakt name returns no results
• QR code on the charger links to a Grønn Kontakt page that no longer works
• RFID card from Grønn Kontakt account rejected

How to Fix It

1. 1

   Update the Mer app to the latest version

   Older versions of the app may not include recently migrated Grønn Kontakt stations. Update from the App Store or Google Play.

2. 2

   Search by the station's physical address

   Instead of searching by station name, try the street address or zoom into the location on the app map. The station may appear under a new Mer name.

3. 3

   Enter the charger ID manually

   Look for a station or connector ID printed on the charger hardware. Enter this ID in the Mer app's manual start option.

4. 4

   Use contactless payment to bypass the app

   If the station has a payment terminal, tap your bank card to start. This works independently of whether the app has the station listed.