Ford E-Transit Charging at Mer

Ford E-Transit Van Charger Will Not Start a Session

You have plugged in your Ford E-Transit but the charger is not starting. When you are on a delivery route, every minute at a non-working charger costs you. Here is how to quickly diagnose and fix the most common reasons the session will not start.

Symptoms

• The CCS2 or Type 2 connector is in but no session starts
• The SYNC display does not show a charging session
• The charger screen displays an error after plugging in
• The charge port light does not illuminate
• The depot charger shows no activity overnight

What to Do

1. 1

   Authenticate with the charger

   Use your fleet charging card, RFID, or the network app to start a session. Make sure the charger confirms the session before plugging in.

2. 2

   Reinsert the connector firmly

   Remove the connector from the E-Transit's charge port on the left front side. Clean any visible dirt or debris, then push the connector back in firmly until it clicks.

3. 3

   Check for departure time settings

   On the SYNC display, go to Charging settings. If a departure time is set, the van may be waiting to start charging. Disable it for immediate charging.

4. 4

   Check the depot charger

   If at the depot, check the wallbox status light and the electrical panel circuit breaker. If multiple vans share a power management system, ask your fleet manager if load balancing is limiting your charger.

5. 5

   Reset the van's charging system

   Turn the van fully off, lock it, wait 30 seconds, then unlock and try again. This can clear fault states from previously interrupted sessions.

6. 6

   Use a different charger

   If on a delivery route, do not waste time troubleshooting a faulty public charger. Move to the next available charger.

Ford E-Transit Van Payment Failed at Charging Station

You are mid-route with deliveries to make and the charger will not accept your payment. Whether it is a fleet card, an RFID card, or an app, payment failures at public chargers waste time you do not have. Here is how to get past it quickly.

Symptoms

• Fleet charging card does not start a session
• RFID card tap produces no response
• The charging app shows a payment error
• Contactless bank card is declined at the charger
• The charger shows 'authorization failed' on screen

What to Do

1. 1

   Check the charger's accepted payment methods

   Look at the stickers on the charger for accepted networks. If your fleet card's logo is not there, this charger is not on your network.

2. 2

   Try a personal payment method

   If the fleet card fails, try a personal RFID card, a charging app, or a contactless bank card. Save the receipt for expense reimbursement.

3. 3

   Check if the fleet card is active

   Call your fleet manager or check the fleet card provider's app to confirm your card is active and not blocked. New or replacement cards sometimes need manual activation.

4. 4

   Hold the card steadily on the reader

   Place the RFID or fleet card flat on the reader and hold for 3 seconds. Van drivers in gloves may not get a clean tap on the first try.

5. 5

   Move to a different charger

   If the payment terminal on this unit is broken, try the next charger at the same station. Do not spend more than 5 minutes troubleshooting when you have deliveries.

6. 6

   Find a charger on your fleet network

   Use your fleet card provider's app to find the nearest charger that accepts your card. Plan your route around compatible chargers.

Ford E-Transit Van Charging Slower Than Expected Speed

You pulled your Ford E-Transit into a DC fast charger between deliveries and the speed is nowhere near 115 kW. Or your depot wallbox is barely delivering power overnight. Slow charging on a commercial van costs you time and money. Here is what is going on and what you can do about it.

Symptoms

• DC fast charging well below the 115 kW maximum
• Depot AC charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after 50-60% state of charge
• Mid-route charging takes longer than expected between deliveries
• The FordPass app shows a longer charge time than planned

What to Do

1. 1

   Navigate to the charger to activate preconditioning

   Before your delivery route, set the DC charger as a waypoint in the E-Transit's SYNC navigation. This warms the battery so it can accept full charging speed when you arrive.

2. 2

   Plan charging stops for low state of charge

   For the fastest mid-route top-ups, charge between 20-60%. This is where the E-Transit delivers its peak DC power. Avoid waiting to charge until the battery is nearly empty.

3. 3

   Check your depot charger setup

   Verify with your electrician or fleet manager that the depot wallbox is wired for three-phase at 16A per phase to deliver the full 11 kW. Single-phase installations deliver only about 3.7 kW.

4. 4

   Choose unshared DC chargers

   At public stations, look for chargers where both connectors are free. If another vehicle is using the paired cable, move to a different unit if time is tight.

5. 5

   Factor payload into range estimates

   A fully loaded E-Transit will have shorter range than the display estimates. Account for this when planning charging stops on your delivery route.

6. 6

   Try a different charger

   If DC speeds are well below 80 kW at a low state of charge with a warm battery, the charger may be degraded. Try another unit.

Station occupancy not updating in the app

The Mer app shows a station as available, but when you arrive, all connectors are occupied or out of service. The real-time status in the app can lag behind by several minutes.

Symptoms

• App shows "Available" but all connectors are in use when you arrive
• App shows a station as occupied but the chargers are visibly free
• Connector status flickers between available and occupied in the app
• Recently freed connectors still show as "In use" in the app for several minutes

How to Fix It

1. 1

   Pull to refresh the station detail in the Mer app

   On the station page, pull down to force a status refresh. The app does not always update automatically, and a manual refresh often shows the correct status.

2. 2

   Close and reopen the app

   Force-close the Mer app and reopen it. This clears any cached station data and pulls a fresh status from the server.

3. 3

   Check a third-party app for a second opinion

   Apps like Plugsurfing, A Better Route Planner, or Google Maps sometimes pull fresher data from Mer's backend. Use one of these to verify availability if the Mer app seems wrong.

4. 4

   Drive to the station if it is nearby

   If the station is less than five minutes away, it is often faster to just go and check. Occupancy can change in the time it takes to troubleshoot the app.

Third-party RFID card rejected

You are trying to authenticate with an RFID card from a roaming provider like Plugsurfing, NewMotion, or Virta, but the Mer charger rejects it. Not all third-party RFID cards are accepted at every Mer station.

Symptoms

• Charger screen shows "Card not recognized" after tapping
• The charger beeps once but nothing happens
• Your RFID card works at other networks but fails at Mer
• The charger prompts you to try again but repeated taps do not help

How to Fix It

1. 1

   Hold the card flat against the reader for three full seconds

   Do not tap and remove quickly. Some Mer readers need a longer hold to register the card. Keep it pressed flat against the RFID symbol.

2. 2

   Check if your roaming provider covers Mer stations

   Open your roaming provider's app and search for this specific Mer station. Some providers have roaming agreements with Mer but not for every station type or region.

3. 3

   Use the Mer app instead

   Download the Mer app if you do not have it. Create an account and add a payment method. You can start the session through the app even if your RFID card does not work.

4. 4

   Try contactless bank card payment

   Newer Mer stations have a contactless payment terminal. Look for a card reader with the contactless payment symbol. Tap your bank card or phone to start.

5. 5

   Try a Mer-issued RFID card for future visits

   You can order an RFID card directly from Mer through their app or website. Mer's own cards are accepted at all Mer stations without roaming issues.

Charger screen showing error but no error code

The charger screen displays a generic error message like "Error" or "Fault" without any specific code or explanation. This makes it hard to know if the problem is temporary or if the unit is broken.

Symptoms

• Charger screen shows "Error" or a red warning icon with no further detail
• The error appears before you even try to authenticate
• The error appears after plugging in but before power delivery starts
• Screen alternates between the normal start screen and the error message

How to Fix It

1. 1

   Unplug the connector and wait 30 seconds

   Some Mer chargers show transient errors after a previous session ended abnormally. Unplugging and waiting gives the charger time to reset its internal state.

2. 2

   Try the other connector on the same unit

   If the station has a second CCS2 connector, try that one. A hardware fault on one connector does not always affect the other.

3. 3

   Check if other cars are successfully charging at the station

   If nobody at the station is charging, the entire station may be down. If others are charging fine, the issue is limited to your connector.

4. 4

   Report the faulty unit in the Mer app

   Open the Mer app, find the station, and report the issue. Include which connector number has the error. This helps Mer send a technician and warns other drivers.

5. 5

   Move to a different station

   A charger with a persistent generic error is unlikely to start working on its own. Use the Mer app to find the nearest alternative station.

Cable locked and will not release in cold weather

You finished charging but the CCS2 cable will not unlock from your car. In Nordic winters, ice can form around the connector locking mechanism, making it physically difficult to release.

Symptoms

• Pressing the connector release button does not unlock the cable
• The connector feels frozen in place
• Your car shows "Charging complete" but the cable is stuck
• The locking pin on the connector is visibly iced over

How to Fix It

1. 1

   Make sure the charging session has fully ended

   The cable stays locked while a session is active. Stop the session in the Mer app or on the charger screen, then try releasing the connector again. Wait 10 seconds after the session ends.

2. 2

   Try unlocking from your car

   Most EVs have a cable release option in the infotainment system or a button near the charge port. Use your car's unlock function rather than the connector button.

3. 3

   Warm the connector gently

   If ice is the problem, pour lukewarm water (not boiling) over the connector and charge port area. You can also cup your hands around the connector to warm it with body heat. Do not use force or tools to pry it free.

4. 4

   Run the car's cabin heater for a few minutes

   Turning on the car's climate system can gradually warm the charge port area from the inside. This works slowly but can free a mildly frozen connector after 5-10 minutes.

5. 5

   Call Mer support if the cable is truly stuck

   If nothing works after 15 minutes, call the support number on the charger. Mer can remotely release the cable lock on their end. Do not pull with excessive force as this can damage both the connector and your car's charge port.

App requires location services for remote start

The Mer app asks you to enable location services before you can start a charging session, even when you are standing right next to the charger and selected it manually from the map.

Symptoms

• App shows "Enable location services to start charging" popup
• Start button is grayed out until location permission is granted
• The app worked fine before but now demands location after an update
• You can browse the map but cannot start a session without GPS enabled

How to Fix It

1. 1

   Enable location services temporarily

   Go to your phone's settings, find the Mer app, and set location access to "While Using the App." You can change it back after your session.

2. 2

   Make sure GPS has a fix

   In underground parking garages or areas with poor GPS reception, the app may not be able to confirm your location. Step outside or move closer to an open area until the app detects your position.

3. 3

   Use RFID or contactless payment instead

   If you do not want to share your location, use your RFID card or a contactless bank card to start the session. These methods do not require the app at all.

4. 4

   Scan the QR code on the charger

   Some Mer chargers have a QR code that opens the start process in a browser, bypassing the app's location requirement.

Former Grønn Kontakt station not found in Mer app

Mer acquired Grønn Kontakt in Norway, but some older stations may not appear correctly in the Mer app, especially during the transition period.

Symptoms

• Station visible on the street but not on the Mer app map
• Searching by the old Grønn Kontakt name returns no results
• QR code on the charger links to a Grønn Kontakt page that no longer works
• RFID card from Grønn Kontakt account rejected

How to Fix It

1. 1

   Update the Mer app to the latest version

   Older versions of the app may not include recently migrated Grønn Kontakt stations. Update from the App Store or Google Play.

2. 2

   Search by the station's physical address

   Instead of searching by station name, try the street address or zoom into the location on the app map. The station may appear under a new Mer name.

3. 3

   Enter the charger ID manually

   Look for a station or connector ID printed on the charger hardware. Enter this ID in the Mer app's manual start option.

4. 4

   Use contactless payment to bypass the app

   If the station has a payment terminal, tap your bank card to start. This works independently of whether the app has the station listed.