Maxus eDeliver 3 Charging at Atlante

Maxus eDeliver 3 Charger Will Not Start Charging

You plugged in the CCS2 cable and nothing happened. Or the charger keeps showing an error. The eDeliver 3 is a solid delivery van, but as a less common brand in Europe, it can occasionally encounter compatibility issues with certain chargers. Most start failures come down to authentication, cable seating, or charger compatibility.

Symptoms

• CCS2 connector plugged in but charger shows no active session
• Charger displays an error code immediately after connecting
• Dashboard shows the charge port is connected but charging does not begin
• Cable does not lock into the CCS2 port on the eDeliver 3
• Charger starts the handshake but fails with a protocol error

What to Do

1. 1

   Remove and reseat the CCS2 connector

   Pull the connector out completely, wait 10 seconds, and push it back in firmly. Make sure it clicks and locks. Check the charge port for debris.

2. 2

   Turn the vehicle off and on

   Switch the eDeliver 3 fully off, wait 30 seconds, then turn it back on. Unplug and replug the cable. This resets the charging communication system.

3. 3

   Re-authenticate with the charger

   Cancel any active session in your charging app and start fresh. If using RFID, hold the card against the reader for a few seconds. Try authenticating before you plug in if the charger supports that flow.

4. 4

   Try a different charger brand

   If the eDeliver 3 will not start on this charger, try a different brand of charger. The eDeliver 3 may have better compatibility with some charger manufacturers. Note which ones work for future reference.

5. 5

   Check for software updates

   Contact your Maxus dealer or check the Maxus app. Software updates can fix charging compatibility issues. The Maxus service network in Europe is smaller, so plan service visits ahead of time.

6. 6

   Contact Maxus support

   If the eDeliver 3 consistently fails to start on multiple chargers, there may be a vehicle-side issue. Contact your Maxus dealer. Keep a log of which chargers failed and any error codes displayed.

Maxus eDeliver 3 Charging Payment Failed at DC

The charger is right there, your eDeliver 3 needs a charge, and the payment just failed. Payment issues at public chargers have nothing to do with your van. They are about the charging network, your card, or your phone signal. Here is how to get around it and get charging.

Symptoms

• Charger displays a payment error or 'transaction declined' message
• Charging app shows 'session failed to start' after payment attempt
• RFID card is not recognized by the charger reader
• Contactless bank card tap does not register
• Authorization starts but times out before the charger delivers power

What to Do

1. 1

   Try a different payment method

   Switch from RFID to app or from app to contactless bank card. Always carry at least two options so one failure does not leave you stranded.

2. 2

   Check your mobile signal

   If signal is weak, the app cannot complete the transaction. Step away from walls or structures and try again.

3. 3

   Verify your payment details

   Open the charging app and check that your card is valid and up to date. Update if the card has been replaced.

4. 4

   Check accepted networks on the charger

   Look for logos showing which networks and apps work at this charger. If yours is not listed, you need a different payment method or a different charger.

5. 5

   Contact your fleet manager

   If using a company RFID card that is not working, your manager can check if the card is active and has no restrictions. Most RFID cards have a support number printed on them.

6. 6

   Find a nearby alternative charger

   If payment is not working here, check your app for the next closest charger on your route. Move on rather than losing delivery time.

Maxus eDeliver 3 Charging Slower Than Expected

You stopped at a public charger expecting a quick top-up and the charger shows 15 kW instead of the 90 kW maximum. The eDeliver 3's 52.5 kWh battery can reach up to 90 kW on DC, but the actual speed depends on temperature, state of charge, and the charger. As a less common brand in Europe, the eDeliver 3 may also encounter occasional charger compatibility quirks. Here is what to check.

Symptoms

• DC fast charging speed well below the 90 kW maximum
• AC charging stuck at about 3 kW instead of the 7 kW maximum
• Charging speed drops sharply after reaching 50-60% on the dashboard
• Charging starts at a reasonable speed but slows down within minutes
• Charger display shows lower power than its rated output

What to Do

1. 1

   Check the battery temperature

   Look at the dashboard for battery temperature information. If the battery is cold, driving for 20-30 minutes before charging can help. The eDeliver 3 lacks preconditioning, so the battery warms up only through driving.

2. 2

   Check your state of charge

   Look at the battery percentage on the dashboard. If you are above 80%, the slower speed is normal. Arrive between 10-20% for the fastest DC charging speeds.

3. 3

   Verify the charger is not sharing power

   Look at the charger. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

4. 4

   Try a different charger brand

   If speeds are consistently low at one type of charger, try a different brand or network. The eDeliver 3 may work better with some charger manufacturers than others due to its less common charging firmware.

5. 5

   Check for vehicle software updates

   Contact your Maxus dealer or check the Maxus app for available software updates. Updates can improve charging compatibility and speeds. The Maxus service network is smaller, so this may require scheduling ahead.

6. 6

   Accept the AC limitation

   If your depot wallbox delivers 7 kW or less, you are already at the eDeliver 3's maximum AC rate. A 3-phase 11 kW or 22 kW wallbox will not charge faster than 7 kW on this van. Plan overnight charging accordingly.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.