Kia EV9 Charging at ABC-lataus

Kia EV9 Charger Won't Start? Step-by-Step Fix Guide

You have plugged the cable into your EV9's right rear charge port, but nothing is happening. No charging indicator on the panoramic display, no LED confirmation. On a large SUV you rely on for family trips or long drives, a failed charge start can be stressful. In most cases, the issue is authentication, utility mode being on, a car setting, or the charger itself.

Symptoms

• CCS2 or Type 2 cable plugged in but no charging indicator on the panoramic display
• Charge port LED stays off or flashes red
• Charger screen shows an error or remains on the start screen
• Kia Connect app shows the car is not connected to a charger
• Charging starts briefly then stops within a few seconds

What to Do

1. 1

   Turn off V2L utility mode

   On the EV9's infotainment screen, go to EV settings. Make sure utility mode or V2L is turned off. Also check the exterior V2L outlet on the rear bumper. If a device was plugged in there, the car may still be in discharge mode.

2. 2

   Check the charge port and cable

   Open the charge port on the right rear fender. The EV9 is a tall vehicle, so the port is relatively high. Press the flap firmly to open. Insert the CCS2 connector straight in until it clicks. The LED should light up.

3. 3

   Authenticate with the charger

   If Plug & Charge does not start the session, tap your RFID card, use the charging network's app, or try contactless payment. Have a backup method ready.

4. 4

   Check for a charging schedule

   On the infotainment screen, go to EV settings, then Scheduled Charging. If a schedule is active, disable it or tap 'Charge Now' to override. The Kia Connect app can also manage schedules.

5. 5

   Unplug, wait 30 seconds, and try again

   Remove the cable completely, wait 30 seconds, reconnect, and re-authenticate. This resets the communication between the EV9 and the charger.

6. 6

   Try a different charger

   If nothing works, try another stall at the same station or a different station. Report the broken charger through the charging network's app.

Kia EV9 Charger Payment Failed at a Public Station

You are at a public charger with your EV9, the CCS2 cable is connected, but the payment will not go through. The charger shows an error, the app is not cooperating, or your RFID card gets nothing. Payment problems are one of the most common reasons charging fails to start, and they are almost never a car problem. Here is how to work through it.

Symptoms

• Charger screen shows 'payment failed' or 'authorization error'
• RFID card tapped but the charger does not respond
• Charging network app shows an error during authorization
• Plug & Charge does not start the session automatically
• Contactless card payment declined at the terminal

What to Do

1. 1

   Try a different payment method

   If RFID failed, try the charging network's app. If the app failed, try contactless payment with a card. Switch between methods quickly rather than retrying the same one.

2. 2

   Check your charging network account

   Open the charging app and check your payment details. Look for expired cards, low prepaid balances, or account issues. Update your payment method if needed.

3. 3

   Verify Plug & Charge configuration

   In the Kia Connect app, check that Plug & Charge is enabled and linked to the correct charging network. Also verify that this specific station supports Plug & Charge. Not all stations do.

4. 4

   Look for a QR code on the charger

   Many chargers have a QR code that opens a web payment page. This lets you pay without an account or app. Scan it with your phone camera.

5. 5

   Try a different charger at the same station

   If one stall's payment terminal is not working, another may be fine. Walk to the next charger and try your payment method again.

Kia EV9 Charging Slower Than Expected at DC or AC

The EV9 is Kia's largest electric SUV, with a 96 kWh battery and 800V architecture that supports up to 233 kW DC charging. When you see 60 kW on the charger screen instead of 200+, it does not match what the specs promise. In most cases, slow charging on the EV9 comes down to battery temperature, the charger's actual voltage and output, or a car setting worth checking.

Symptoms

• DC fast charging speed well below the 233 kW maximum
• AC charging stuck at 3-4 kW instead of the full 11 kW
• Charging speed drops sharply above 60-70% state of charge
• Session starts at low power and never ramps up
• Panoramic display shows much lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature

   Look at the EV information on the panoramic display. If the battery is cold, use the built-in navigation to set a charging destination. The EV9 will precondition the battery automatically on the way. This is especially important in winter given the large battery.

2. 2

   Check whether the charger supports 800V

   Look at the charger specs on its screen or in the charging network's app. If it is a 400V charger, the EV9's multi-charging system handles the conversion, but you will not see 233 kW. Seek out chargers that explicitly list 800V support.

3. 3

   Check your state of charge

   If you are above 80%, the speed drop is normal. For road trips, plan stops to arrive between 10-20% and unplug at 80%. The EV9's consumption is around 204 Wh/km, so factor that into your stop planning.

4. 4

   Review scheduled charging and charge limits

   On the EV settings screen or in the Kia Connect app, check that scheduled charging is not delaying the session and the charge current limit is at maximum.

5. 5

   Check if the charger is sharing power

   Look at the charger cabinet. If two cables come from the same unit and someone is on the other cable, your speed may be halved. Move to an unoccupied charger if one is available.

6. 6

   Try a different charger or station

   If speed is still low after checking everything, the charger may be underperforming its rated output. Try another stall or head to a different station.

Session fails to start or charger shows an error

You plug in and try to authenticate, but the charger does not begin charging. This can happen due to communication issues between your vehicle and the charger, or a problem with authentication.

Symptoms

• Charger shows an error after you try to start a session
• Contactless card payment does not work at this station (older unit without payment terminal)
• Card reader beeps but the session does not start
• The app says the session is starting but nothing happens at the charger

How to Fix It

1. 1

   Unplug, wait 30 seconds, and try again

   The initial communication handshake between your vehicle and the charger can fail. Unplug the connector, wait at least 30 seconds, and reconnect. The second attempt often works.

2. 2

   Try starting the session through the ABC-lataus app

   If the card reader is not cooperating, open the ABC-lataus app, select the station, and start the session from your phone. This bypasses the physical card reader entirely.

3. 3

   Try contactless card payment at newer stations

   Some newer ABC-lataus high-power stations have a contactless payment terminal. If the app is not cooperating, look for a card reader on the charger unit and tap your bank card. Older stations may not have this option.

4. 4

   Try a different charger unit at the same station

   If the station has multiple charger units, switch to another one. One unit may have a hardware issue while the others work fine.

Finding the EV charger at a busy fuel station

ABC-lataus chargers are located at ABC fuel stations, which also serve diesel and petrol vehicles. The EV charging spots can be easy to miss if you are visiting for the first time.

Symptoms

• You arrived at the ABC station but cannot see the EV charger
• The charger is behind the fuel pump area or in a separate parking section
• Other vehicles (non-EV) are parked in the charging spots
• Signage is not visible from the main road entrance

How to Fix It

1. 1

   Check the ABC-lataus app for the charger's exact location

   The app shows station details including photos or layout hints. Some ABC stations place chargers at the far end of the parking area, away from the fuel pumps.

2. 2

   Look for the CCS2 cable and charging unit

   The charger unit is taller than a fuel pump and usually has a clearly different design. Look for a separate bay with a CCS2 cable, often marked with green signage or an EV symbol on the ground.

3. 3

   Drive past the fuel pumps

   At many ABC stations, the EV charger is positioned after the fuel pump area or in a dedicated corner of the parking lot. Do not stop at the fuel pumps. Continue through and scan for the charging unit.

4. 4

   If an ICE vehicle is blocking the spot, report it

   ABC stations serve all types of vehicles. If a non-EV is parked in the charging bay, contact ABC customer service through the app. Unfortunately, there is not much you can do in the moment besides trying another station.

App setup confusion within the S-Group ecosystem

The ABC-lataus app is part of the S-Group digital ecosystem. If you already use S-mobiili for groceries or fuel, the relationship between the apps can be confusing.

Symptoms

• You are not sure whether to use S-mobiili or the ABC-lataus app
• Your S-Group login works in one app but not the other
• Charging payments do not appear in your S-mobiili transaction history
• You created a new account instead of linking your existing S-Group membership

How to Fix It

1. 1

   Use the ABC-lataus app for starting and managing charging sessions

   While S-mobiili handles your broader S-Group membership, the ABC-lataus app is the dedicated tool for finding stations, starting sessions, and viewing charging history. Install it separately from the App Store or Google Play.

2. 2

   Log in with your existing S-Group credentials

   Use the same username and password you use for S-mobiili or s-kanava.fi. Do not create a new account.

3. 3

   Check payment method settings in the ABC-lataus app

   Even if you have a payment card saved in S-mobiili, the ABC-lataus app may require you to add a payment method separately. Go to settings or payment in the ABC-lataus app and add your card there.

4. 4

   Verify your account is set up for charging

   Check the ABC-lataus app settings to make sure your payment method is saved and charging is enabled.

Connector stuck or difficult to insert in winter cold

Finnish winters mean temperatures well below freezing. The CCS2 connector locking mechanism and the vehicle's charge port can freeze, making it hard to plug in or unplug.

Symptoms

• The CCS2 connector will not click into your vehicle's charge port
• The connector is plugged in but the locking mechanism will not engage
• You cannot release the connector after charging is complete
• The connector handle feels stiff or the release button is frozen

How to Fix It

1. 1

   Check your vehicle's charge port for ice

   Open the charge port door and look for ice buildup around the opening or inside the port. Brush away any loose ice or snow with your hand or a soft brush. Do not use sharp tools, as you can damage the pins.

2. 2

   Warm the connector in your hands for a moment

   If the connector handle feels frozen stiff, hold it in your hands for 30 seconds to warm the mechanism slightly. The locking button and release lever work better when they are not frozen solid.

3. 3

   Push the connector in firmly and straight

   In cold weather, plastic contracts and tolerances get tighter. Line up the connector carefully and push it in with steady, even pressure. Do not force it at an angle.

4. 4

   If the connector is stuck after charging, try unlocking from your car

   Use your vehicle's unlock button or the in-car menu to release the charge port lock. Some vehicles also release the connector when you unlock the doors. If it is still stuck, wait a few minutes. The charging session generates heat that may free the mechanism.

5. 5

   Contact support if the connector will not release

   Do not yank the connector. Forcing it can damage both the cable and your vehicle's charge port. Call ABC-lataus support and they can guide you through a remote release or send help.

Charging session starts but power delivery is low

The charger is rated for 200 kW, but your session is delivering significantly less. Several factors specific to ABC-lataus stations can contribute.

Symptoms

• Dashboard shows 30 to 50 kW at a 200 kW rated charger
• Charging speed drops after a few minutes
• Speed is lower than what you get at other fast chargers
• The charger screen shows a lower maximum than 200 kW

How to Fix It

1. 1

   Check your vehicle's maximum DC charging rate

   A 200 kW charger does not mean your vehicle can accept 200 kW. Many EVs max out at 50 to 150 kW depending on the model, battery temperature, and state of charge. Check your vehicle's specifications.

2. 2

   Consider battery temperature in Finnish conditions

   Cold batteries accept less power. If your vehicle has been parked outside in freezing temperatures, the battery may need to warm up before it can accept higher charging speeds. Some vehicles have a preconditioning feature you can activate before arriving.

3. 3

   Check if another vehicle is sharing the station's power

   Some ABC-lataus locations share power between charger units. If another vehicle is charging at the same station, your available power may be split. This is normal and not a fault.

4. 4

   Arrive with a lower state of charge for faster charging

   Charging is fastest between 10% and 50% state of charge. If you arrive at 60% or higher, the charger will taper the power to protect your battery. This is your vehicle's doing, not the charger's.