Audi e-tron GT Charging at Shell Recharge

Audi e-tron GT Charger Won't Start Charging

You have plugged in your e-tron GT, but nothing happens. The MMI screen stays silent or shows an error. The e-tron GT has two charge ports, one on the left rear for AC and one on the right rear for DC, which can add confusion. This is frustrating, but it is almost always fixable on the spot.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the MMI touchscreen
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• e-tron GT charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Plugged into the wrong charge port for the type of charging

What to Do

1. 1

   Verify you are using the correct charge port

   For DC fast charging, use the charge port on the right rear of the car. For AC charging with a Type 2 cable, use the charge port on the left rear. Using the wrong port is the most common cause of a failed start on the e-tron GT.

2. 2

   Check for a charging schedule or departure timer

   On the MMI touchscreen, go to the e-tron charging settings. If a timer or departure schedule is active, switch it to charge immediately or turn off the timer. You can also check the myAudi app for active schedules.

3. 3

   Unplug and reconnect firmly

   Remove the connector, wait 10 seconds, then reinsert it firmly into the correct charge port until you hear a clear click. Watch the charge port LED for a steady response.

4. 4

   Restart the charger session

   On the charger, end the current session if one is active. Then start a new session by tapping your RFID card, using contactless payment, or restarting in the charger operator's app.

5. 5

   Reboot the MMI system

   Press and hold the power button on the MMI touchscreen for about 10 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication on the car's side.

6. 6

   Try a different charger

   If the station has multiple stalls, move to a different one. Some chargers have firmware issues that cause 800V handshake failures. A different unit at the same station may work fine.

Audi e-tron GT Charging Payment Failed at Station

You are at the charger, your e-tron GT is plugged in, but the payment will not go through. The charger shows an error or just sits there waiting. Payment failures at public chargers are common and usually have nothing to do with your car. Here is how to get charging.

Symptoms

• Charger displays 'Payment failed' or 'Authorization error' after tapping your card
• RFID card is not recognized by the charger's reader
• myAudi or Audi charging app shows an error when trying to start a remote session
• Plug & Charge does not activate after plugging in the CCS2 connector on the right rear
• Contactless payment terminal on the charger rejects your bank card

What to Do

1. 1

   Try a different payment method

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having two or three payment options gives you the best chance of getting going.

2. 2

   Check the myAudi app

   Open the myAudi app on your phone. Make sure your Audi charging account is active, your payment method is valid, and Plug & Charge is enabled if you want to use it. Try starting the session remotely through the app.

3. 3

   Scan the charger's QR code

   Most public chargers have a QR code on the unit. Scanning it with your phone's camera opens the operator's payment page. You can usually pay with a credit card through the browser without downloading an app.

4. 4

   Check your bank app for blocked transactions

   Open your banking app and check for any flagged or blocked transactions. Some banks require you to approve the charge manually. If you see a notification, approve it and try the payment again.

5. 5

   Try Plug & Charge if available

   If the charger supports Plug & Charge and your e-tron GT has it activated through the myAudi app, simply unplug and replug the CCS2 connector into the right rear charge port. The payment should authorize automatically through the cable.

6. 6

   Move to a different charger

   If nothing works at this station, the charger's payment system may be down entirely. Find a nearby alternative using the myAudi app or the e-tron GT's built-in charger finder on the MMI touchscreen.

Audi e-tron GT Charging Slower Than Expected

You plugged in your e-tron GT expecting 270 kW and the MMI touchscreen shows 50 kW. With an 800V architecture designed for ultra-fast charging, this is especially frustrating. Slow charging on the e-tron GT is almost never a defect. It is usually the charger's capability, the battery temperature, or a mismatch between the station's voltage and the car's 800V system.

Symptoms

• DC fast charging speed well below the 270 kW maximum shown on the MMI touchscreen
• AC home charging stuck at 3-4 kW instead of the full 11 kW or optional 22 kW
• Charging speed drops significantly after reaching 50-60% state of charge
• The e-tron GT charges at similar speeds to 400V vehicles despite having 800V architecture
• MMI display shows lower power than the charger's rated output

What to Do

1. 1

   Verify the charger supports 800V and high power

   Check the charger's label or the operator's app for the maximum power output and voltage. For the e-tron GT to reach its peak 270 kW, you need a charger rated for at least 270 kW at 800V. A 150 kW or 400V charger will work but at much lower speeds.

2. 2

   Check the battery temperature

   Look at the charging screen on the MMI touchscreen. If the battery is cold, use the navigation system to route to the fast charger. The e-tron GT will precondition the battery on the way using its heat pump. If you are already at the charger, driving for 15-20 minutes and returning can help.

3. 3

   Check your state of charge

   Look at the digital instrument cluster or MMI screen. If you are above 80%, the slower speed is expected. For the fastest charging, arrive at the charger between 5-20% and charge to 80%.

4. 4

   Verify the charger is not sharing power

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

5. 5

   Check the AC charge current setting

   On the MMI touchscreen, go to the e-tron charging settings. Make sure the AC charge current is set to maximum. If you have the optional 22 kW onboard charger, verify your wallbox supports it.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Look for Ionity, Electrify America, or other 350 kW networks that support 800V to get the best speeds from your e-tron GT.

RFID card not recognized at the charger

You tap your Shell Recharge RFID card on the charger's reader but it does not respond, beeps an error, or shows 'Card not recognized.'

Symptoms

• Charger beeps but displays 'Unknown card' or 'Authorization failed'
• No response at all when tapping the card
• Card works at some stations but not others
• Card worked yesterday at the same charger but does not work today

How to Fix It

1. 1

   Hold the card still on the reader for 3 to 5 seconds

   RFID readers at some chargers are slow. Do not tap and remove quickly. Hold the card flat against the reader and wait for a confirmation beep or screen change.

2. 2

   Check that your RFID card is activated

   New Shell Recharge RFID cards must be activated in the Shell Recharge app before first use. Go to the app, find the RFID section, and make sure the card status shows active.

3. 3

   Try starting the session through the app instead

   Open the Shell Recharge app, find the station, select the charger, and start the session digitally. This bypasses the RFID reader entirely and uses the roaming connection.

4. 4

   Check if the CPO supports Shell Recharge roaming

   Not every charger that appears in the Shell Recharge app accepts the Shell Recharge RFID card. Some chargers only accept app-based roaming. The station details in the app usually indicate which payment methods are supported.

5. 5

   Clean the card and try again

   Dirt, scratches, or a phone case between the card and reader can block the RFID signal. Remove the card from any holder, wipe it, and try again on the reader's sweet spot (often marked with a contactless symbol).

Roaming vs direct pricing confusion

The price you pay through Shell Recharge is different from the price shown on the charger's screen. This is because Shell Recharge adds a roaming markup on top of the CPO's base rate.

Symptoms

• Charger screen shows 0.39 EUR/kWh but Shell Recharge bills 0.55 EUR/kWh
• Invoice includes fees not displayed at the charger (session fee, per-minute fee)
• Same station is cheaper when using the CPO's own app
• Pricing in the Shell Recharge app does not match the final invoice

How to Fix It

1. 1

   Check the Shell Recharge app for the roaming price before starting

   Before you tap your card or start a session, open the Shell Recharge app and select the station. The app shows the Shell Recharge price, which includes any roaming fee. This is the price you will actually pay.

2. 2

   Understand the pricing structure

   Shell Recharge typically charges a per-kWh rate plus sometimes a session start fee or per-minute fee. The charger screen shows the CPO's direct price, not the roaming price. These are two different rates for two different billing relationships.

3. 3

   Consider using the CPO's own app for lower rates

   If you charge at the same network regularly (for example, Allego, Fastned, or EnBW), their own app usually offers a lower price than roaming through Shell Recharge. The trade-off is managing multiple apps.

4. 4

   Download your invoice from the Shell Recharge app

   Go to your charging history in the Shell Recharge app. Each session has a detailed breakdown showing energy delivered, per-kWh rate, session fees, and total cost. Compare this with what you expected.

Session not starting via QR code

You scan the QR code on the charger to start a session through the Shell Recharge app, but nothing happens or you get an error.

Symptoms

• QR code opens the Shell Recharge app but shows 'Station not found'
• QR code opens a web page instead of the app
• App shows 'Unable to start session' after scanning
• QR code is faded, damaged, or partially covered by a sticker

How to Fix It

1. 1

   Search for the station manually in the app

   If the QR code does not work, open the Shell Recharge app, search for the station by name or location, and start the session from the station page. You may need to select the specific connector or charger ID.

2. 2

   Check the charger ID number

   Every charger has an ID printed somewhere on the unit (usually near the QR code or on a label). Enter this ID manually in the Shell Recharge app if the QR scan fails.

3. 3

   Make sure the QR code belongs to Shell Recharge

   Many chargers have multiple QR codes from different roaming providers and the CPO itself. Make sure you are scanning the Shell Recharge QR code, not the CPO's own code. Scanning the wrong code opens the wrong app or website.

4. 4

   Try the RFID card or contactless payment instead

   QR code start is just one method. Tap your Shell Recharge RFID card or use contactless payment if the charger supports it.

5. 5

   Check your internet connection

   Starting a session via QR code requires the app to communicate with Shell Recharge's servers and the CPO's backend. If you have weak mobile signal (common at highway rest stops), the request may time out. Try switching between Wi-Fi and mobile data.

App showing wrong charger status

The Shell Recharge app shows a charger as available, occupied, or offline, but the actual status is different when you arrive.

Symptoms

• App shows 'Available' but the charger is out of order or has an error screen
• App shows 'Occupied' but no vehicle is connected
• Status has not updated for hours and seems stale
• App shows fewer chargers at a station than physically exist

How to Fix It

1. 1

   Understand that status data is delayed

   Shell Recharge gets charger status from the CPO's systems through the roaming connection. This data can lag by 5 to 15 minutes. A charger that just became available may still show as occupied in the app.

2. 2

   Try plugging in regardless of app status

   If you are already at the station and a charger looks physically available (no vehicle connected, no error on screen), try plugging in and starting a session. The real-time status at the charger overrides whatever the app shows.

3. 3

   Check the CPO's own app for more accurate status

   The CPO (the company that actually operates the charger) usually has more accurate real-time status than roaming aggregators like Shell Recharge. If accuracy matters, cross-check with the CPO's app or website.

4. 4

   Report the incorrect status

   Use the Shell Recharge app to report the charger issue. This helps improve status accuracy over time.

Billing discrepancy between Shell Recharge and the CPO

The amount billed by Shell Recharge does not match what you expected based on the energy delivered or the session duration. This can happen because of how roaming billing works.

Symptoms

• Billed for more kWh than your vehicle's dashboard shows
• Charged a session fee you did not expect
• Per-minute idle fee added even though you unplugged on time
• Double charge: both Shell Recharge and the CPO billed you

How to Fix It

1. 1

   Compare the Shell Recharge invoice with your vehicle's data

   Your vehicle's dashboard shows how much energy the battery received. The charger meters how much energy it delivered, which includes conversion losses. A 5 to 10% difference is normal.

2. 2

   Check for per-minute fees

   Some CPOs charge a per-minute fee (for time spent connected) on top of the per-kWh fee. This can be especially costly during slow AC charging sessions. Check the pricing breakdown in the Shell Recharge app.

3. 3

   Look for session or start fees

   Some stations add a fixed fee per session (for example, 0.35 EUR to 1.00 EUR). This appears in the Shell Recharge invoice as a separate line item.

4. 4

   Dispute the charge through the Shell Recharge app

   If the amount is clearly wrong (double billed, charged for a session that never started, or obviously excessive), contact Shell Recharge support through the app. Go to your charging history, select the session, and use the dispute or help option.

5. 5

   Keep your vehicle's charge data as evidence

   Take a photo of your vehicle's charging screen or dashboard showing the kWh received and the session duration. This is useful if you need to dispute a charge.