Audi e-tron GT Charging at Recharge

Audi e-tron GT Charger Won't Start Charging

You have plugged in your e-tron GT, but nothing happens. The MMI screen stays silent or shows an error. The e-tron GT has two charge ports, one on the left rear for AC and one on the right rear for DC, which can add confusion. This is frustrating, but it is almost always fixable on the spot.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the MMI touchscreen
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• e-tron GT charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Plugged into the wrong charge port for the type of charging

What to Do

1. 1

   Verify you are using the correct charge port

   For DC fast charging, use the charge port on the right rear of the car. For AC charging with a Type 2 cable, use the charge port on the left rear. Using the wrong port is the most common cause of a failed start on the e-tron GT.

2. 2

   Check for a charging schedule or departure timer

   On the MMI touchscreen, go to the e-tron charging settings. If a timer or departure schedule is active, switch it to charge immediately or turn off the timer. You can also check the myAudi app for active schedules.

3. 3

   Unplug and reconnect firmly

   Remove the connector, wait 10 seconds, then reinsert it firmly into the correct charge port until you hear a clear click. Watch the charge port LED for a steady response.

4. 4

   Restart the charger session

   On the charger, end the current session if one is active. Then start a new session by tapping your RFID card, using contactless payment, or restarting in the charger operator's app.

5. 5

   Reboot the MMI system

   Press and hold the power button on the MMI touchscreen for about 10 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication on the car's side.

6. 6

   Try a different charger

   If the station has multiple stalls, move to a different one. Some chargers have firmware issues that cause 800V handshake failures. A different unit at the same station may work fine.

Audi e-tron GT Charging Payment Failed at Station

You are at the charger, your e-tron GT is plugged in, but the payment will not go through. The charger shows an error or just sits there waiting. Payment failures at public chargers are common and usually have nothing to do with your car. Here is how to get charging.

Symptoms

• Charger displays 'Payment failed' or 'Authorization error' after tapping your card
• RFID card is not recognized by the charger's reader
• myAudi or Audi charging app shows an error when trying to start a remote session
• Plug & Charge does not activate after plugging in the CCS2 connector on the right rear
• Contactless payment terminal on the charger rejects your bank card

What to Do

1. 1

   Try a different payment method

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having two or three payment options gives you the best chance of getting going.

2. 2

   Check the myAudi app

   Open the myAudi app on your phone. Make sure your Audi charging account is active, your payment method is valid, and Plug & Charge is enabled if you want to use it. Try starting the session remotely through the app.

3. 3

   Scan the charger's QR code

   Most public chargers have a QR code on the unit. Scanning it with your phone's camera opens the operator's payment page. You can usually pay with a credit card through the browser without downloading an app.

4. 4

   Check your bank app for blocked transactions

   Open your banking app and check for any flagged or blocked transactions. Some banks require you to approve the charge manually. If you see a notification, approve it and try the payment again.

5. 5

   Try Plug & Charge if available

   If the charger supports Plug & Charge and your e-tron GT has it activated through the myAudi app, simply unplug and replug the CCS2 connector into the right rear charge port. The payment should authorize automatically through the cable.

6. 6

   Move to a different charger

   If nothing works at this station, the charger's payment system may be down entirely. Find a nearby alternative using the myAudi app or the e-tron GT's built-in charger finder on the MMI touchscreen.

Audi e-tron GT Charging Slower Than Expected

You plugged in your e-tron GT expecting 270 kW and the MMI touchscreen shows 50 kW. With an 800V architecture designed for ultra-fast charging, this is especially frustrating. Slow charging on the e-tron GT is almost never a defect. It is usually the charger's capability, the battery temperature, or a mismatch between the station's voltage and the car's 800V system.

Symptoms

• DC fast charging speed well below the 270 kW maximum shown on the MMI touchscreen
• AC home charging stuck at 3-4 kW instead of the full 11 kW or optional 22 kW
• Charging speed drops significantly after reaching 50-60% state of charge
• The e-tron GT charges at similar speeds to 400V vehicles despite having 800V architecture
• MMI display shows lower power than the charger's rated output

What to Do

1. 1

   Verify the charger supports 800V and high power

   Check the charger's label or the operator's app for the maximum power output and voltage. For the e-tron GT to reach its peak 270 kW, you need a charger rated for at least 270 kW at 800V. A 150 kW or 400V charger will work but at much lower speeds.

2. 2

   Check the battery temperature

   Look at the charging screen on the MMI touchscreen. If the battery is cold, use the navigation system to route to the fast charger. The e-tron GT will precondition the battery on the way using its heat pump. If you are already at the charger, driving for 15-20 minutes and returning can help.

3. 3

   Check your state of charge

   Look at the digital instrument cluster or MMI screen. If you are above 80%, the slower speed is expected. For the fastest charging, arrive at the charger between 5-20% and charge to 80%.

4. 4

   Verify the charger is not sharing power

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

5. 5

   Check the AC charge current setting

   On the MMI touchscreen, go to the e-tron charging settings. Make sure the AC charge current is set to maximum. If you have the optional 22 kW onboard charger, verify your wallbox supports it.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Look for Ionity, Electrify America, or other 350 kW networks that support 800V to get the best speeds from your e-tron GT.

Charger stuck in "preparing" state

You authenticated successfully, the charger says "preparing," but it never starts delivering power. This is one of the most reported issues on Recharge stations, especially at older units.

Symptoms

• Charger screen shows "Preparing" or "Initializing" for more than two minutes
• Your car's charging indicator does not activate
• The Recharge app shows the session as active but 0 kW delivered
• The charger fan spins up but no power flows

How to Fix It

1. 1

   Wait up to three minutes

   Some Recharge units, particularly the 300kW stations, take longer to complete the power handshake with your car. Give it a full three minutes before taking action.

2. 2

   Unplug and reconnect

   Remove the CCS2 connector, wait 15 seconds, then plug it back in firmly. This resets the communication between your car and the charger.

3. 3

   Stop the session in the Recharge app and start a new one

   Open the Recharge app, tap Stop on the active session, wait for it to fully end, then start a new session on the same charger. This clears any stuck state on the backend.

4. 4

   Try the other connector on the same unit

   Many Recharge stations have two CCS2 connectors. If one is stuck, the other connector on the same unit often works fine.

5. 5

   Use a different authentication method

   If you started with the app, try your RFID card instead, or vice versa. Sometimes the issue is with the authentication path, not the charger hardware.

Old Fortum branding causes app scan failure

Recharge was originally part of Fortum's charging operations before being spun off as a separate company. Some older stations still display Fortum logos and QR codes. Scanning an old Fortum QR code with the Recharge app may not work, or it may redirect to a dead Fortum page.

Symptoms

• QR code on the charger opens a Fortum website or shows an error
• Recharge app says "Charger not found" after scanning
• Station ID on the physical unit does not match what the Recharge app expects
• The charger has Fortum branding but is listed as Recharge in third-party apps

How to Fix It

1. 1

   Ignore the QR code and search by station name in the Recharge app

   Open the Recharge app, use the map or search to find the station by location. The charger will appear under its Recharge name even if the physical unit still says Fortum.

2. 2

   Enter the charger ID manually

   Look for a numeric ID on the charger, often printed on a sticker near the connector. In the Recharge app, tap "Enter ID" and type it in directly.

3. 3

   Use RFID or contactless payment instead of the app

   Tap your Recharge RFID card or a contactless bank card on the reader. This bypasses the app entirely and works regardless of the branding on the charger.

4. 4

   Check if contactless is available on this unit

   Not all Recharge stations support contactless bank card payment. Look for a card reader terminal on the charger. If there is no terminal, you will need the app or an RFID card.

RFID card from old Fortum account not recognized

If you had a Fortum Charge & Drive account and RFID card, it may not work automatically on the Recharge network. Some cards were migrated, others were not.

Symptoms

• Tapping your old Fortum RFID card shows "Card not recognized" on the charger
• The charger beeps but does not start a session
• Your Fortum card works on some stations but not others

How to Fix It

1. 1

   Log in to the Recharge app and check your RFID cards

   Open the Recharge app, go to your account settings, and look under RFID cards. If your old Fortum card is not listed, it was not migrated automatically.

2. 2

   Re-register your RFID card

   In the Recharge app, tap "Add RFID card" and follow the steps. You will need the card number printed on the back of your RFID card.

3. 3

   Use the app to start the session while you wait for RFID activation

   RFID card registration can take up to 24 hours to propagate across all stations. Use the app to authenticate in the meantime.

4. 4

   Order a new Recharge RFID card if re-registration fails

   Some older Fortum cards use a chip format that is not compatible. You can order a new Recharge RFID card through the app or website.

Contactless payment not accepted

You are trying to tap your bank card or phone to pay, but the charger does not respond or shows an error. Contactless payment availability varies across Recharge stations.

Symptoms

• No card reader terminal visible on the charger
• Card reader shows "Payment failed" or does not respond to taps
• Apple Pay or Google Pay not recognized
• The charger prompts for an RFID card but you only have a bank card

How to Fix It

1. 1

   Check if this station supports contactless payment

   Look for a separate payment terminal with a contactless symbol. Not all Recharge stations have been upgraded. The Recharge app shows payment options for each station on the station detail page.

2. 2

   Try removing and re-holding your card

   Hold your card flat against the reader for at least three seconds. Some terminals need a longer hold than you might expect. Remove the card fully, then try again.

3. 3

   Fall back to the Recharge app

   If contactless is not working, open the Recharge app and start the session from there. You need a payment method saved in the app.

4. 4

   Try a different card

   Some Visa Electron and certain prepaid cards are not accepted by the payment terminals. A standard Visa or Mastercard debit or credit card usually works.

Charging speed much lower than expected

The station is rated for 300kW, but your car is only pulling 50kW or less. While your car's battery management limits the maximum speed, Recharge stations can also throttle power.

Symptoms

• Charger display shows far less power than the station's rated capacity
• Charging speed drops suddenly mid-session
• Other cars at the same station are also charging slowly
• The Recharge app shows the session but at low power

How to Fix It

1. 1

   Check how many other cars are charging at the same station

   Recharge stations with multiple connectors often share a power cabinet. If two or three cars are charging simultaneously, the available power per car drops. This is normal and not a fault.

2. 2

   Check your battery level

   DC fast charging slows significantly above 80% on most EVs. If your battery is above 70-80%, the slower speed is your car protecting the battery, not a problem with the Recharge station.

3. 3

   Check the temperature

   In cold weather, your car may limit charging speed until the battery warms up. This can take 10-15 minutes of charging before speeds increase. Some cars precondition the battery if you set the charger as a destination in navigation.

4. 4

   Try a different connector at the station

   Individual connectors can have faults that limit power output. If another connector is free, unplug and try it.

5. 5

   Report the issue in the Recharge app

   If the speed is unusually low and none of the above apply, report it through the Recharge app. Tap the active session and look for a "Report issue" option. This helps Recharge identify hardware problems.