Audi e-tron GT Charging at EnBW mobility+

Audi e-tron GT Charger Won't Start Charging

You have plugged in your e-tron GT, but nothing happens. The MMI screen stays silent or shows an error. The e-tron GT has two charge ports, one on the left rear for AC and one on the right rear for DC, which can add confusion. This is frustrating, but it is almost always fixable on the spot.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the MMI touchscreen
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• e-tron GT charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Plugged into the wrong charge port for the type of charging

What to Do

1. 1

   Verify you are using the correct charge port

   For DC fast charging, use the charge port on the right rear of the car. For AC charging with a Type 2 cable, use the charge port on the left rear. Using the wrong port is the most common cause of a failed start on the e-tron GT.

2. 2

   Check for a charging schedule or departure timer

   On the MMI touchscreen, go to the e-tron charging settings. If a timer or departure schedule is active, switch it to charge immediately or turn off the timer. You can also check the myAudi app for active schedules.

3. 3

   Unplug and reconnect firmly

   Remove the connector, wait 10 seconds, then reinsert it firmly into the correct charge port until you hear a clear click. Watch the charge port LED for a steady response.

4. 4

   Restart the charger session

   On the charger, end the current session if one is active. Then start a new session by tapping your RFID card, using contactless payment, or restarting in the charger operator's app.

5. 5

   Reboot the MMI system

   Press and hold the power button on the MMI touchscreen for about 10 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication on the car's side.

6. 6

   Try a different charger

   If the station has multiple stalls, move to a different one. Some chargers have firmware issues that cause 800V handshake failures. A different unit at the same station may work fine.

Audi e-tron GT Charging Payment Failed at Station

You are at the charger, your e-tron GT is plugged in, but the payment will not go through. The charger shows an error or just sits there waiting. Payment failures at public chargers are common and usually have nothing to do with your car. Here is how to get charging.

Symptoms

• Charger displays 'Payment failed' or 'Authorization error' after tapping your card
• RFID card is not recognized by the charger's reader
• myAudi or Audi charging app shows an error when trying to start a remote session
• Plug & Charge does not activate after plugging in the CCS2 connector on the right rear
• Contactless payment terminal on the charger rejects your bank card

What to Do

1. 1

   Try a different payment method

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having two or three payment options gives you the best chance of getting going.

2. 2

   Check the myAudi app

   Open the myAudi app on your phone. Make sure your Audi charging account is active, your payment method is valid, and Plug & Charge is enabled if you want to use it. Try starting the session remotely through the app.

3. 3

   Scan the charger's QR code

   Most public chargers have a QR code on the unit. Scanning it with your phone's camera opens the operator's payment page. You can usually pay with a credit card through the browser without downloading an app.

4. 4

   Check your bank app for blocked transactions

   Open your banking app and check for any flagged or blocked transactions. Some banks require you to approve the charge manually. If you see a notification, approve it and try the payment again.

5. 5

   Try Plug & Charge if available

   If the charger supports Plug & Charge and your e-tron GT has it activated through the myAudi app, simply unplug and replug the CCS2 connector into the right rear charge port. The payment should authorize automatically through the cable.

6. 6

   Move to a different charger

   If nothing works at this station, the charger's payment system may be down entirely. Find a nearby alternative using the myAudi app or the e-tron GT's built-in charger finder on the MMI touchscreen.

Audi e-tron GT Charging Slower Than Expected

You plugged in your e-tron GT expecting 270 kW and the MMI touchscreen shows 50 kW. With an 800V architecture designed for ultra-fast charging, this is especially frustrating. Slow charging on the e-tron GT is almost never a defect. It is usually the charger's capability, the battery temperature, or a mismatch between the station's voltage and the car's 800V system.

Symptoms

• DC fast charging speed well below the 270 kW maximum shown on the MMI touchscreen
• AC home charging stuck at 3-4 kW instead of the full 11 kW or optional 22 kW
• Charging speed drops significantly after reaching 50-60% state of charge
• The e-tron GT charges at similar speeds to 400V vehicles despite having 800V architecture
• MMI display shows lower power than the charger's rated output

What to Do

1. 1

   Verify the charger supports 800V and high power

   Check the charger's label or the operator's app for the maximum power output and voltage. For the e-tron GT to reach its peak 270 kW, you need a charger rated for at least 270 kW at 800V. A 150 kW or 400V charger will work but at much lower speeds.

2. 2

   Check the battery temperature

   Look at the charging screen on the MMI touchscreen. If the battery is cold, use the navigation system to route to the fast charger. The e-tron GT will precondition the battery on the way using its heat pump. If you are already at the charger, driving for 15-20 minutes and returning can help.

3. 3

   Check your state of charge

   Look at the digital instrument cluster or MMI screen. If you are above 80%, the slower speed is expected. For the fastest charging, arrive at the charger between 5-20% and charge to 80%.

4. 4

   Verify the charger is not sharing power

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

5. 5

   Check the AC charge current setting

   On the MMI touchscreen, go to the e-tron charging settings. Make sure the AC charge current is set to maximum. If you have the optional 22 kW onboard charger, verify your wallbox supports it.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Look for Ionity, Electrify America, or other 350 kW networks that support 800V to get the best speeds from your e-tron GT.

Roaming pricing unclear or higher than expected

You started a session through EnBW mobility+ and the per-kWh price was significantly higher than you expected. The same charger costs different amounts at different times, and the pricing logic feels opaque.

Symptoms

• Per-kWh rate on the receipt is higher than the rate shown on the EnBW website
• Same charger location costs more through EnBW mobility+ than through the CPO's own app
• Price differs between two chargers at the same station
• Unexpected 'roaming fee' or 'session fee' on your invoice

How to Fix It

1. 1

   Check the price before you start the session

   In the EnBW mobility+ app, tap on the charger and look for the pricing details before starting. The app shows the per-kWh rate for that specific charger. Prices vary because each CPO sets different roaming rates.

2. 2

   Understand the pricing tiers

   EnBW mobility+ groups chargers into pricing tiers. 'EnBW own' chargers are cheapest, 'roaming standard' is mid-range, and 'roaming plus' (typically high-power chargers from premium CPOs like Ionity) costs more. The tier is usually shown in the charger details.

3. 3

   Compare with the CPO's own app

   If a charger is operated by Ionity, for example, check the Ionity app or website for their direct pricing. Sometimes the CPO's own app or RFID card is cheaper because there is no roaming middleman. If you use that CPO frequently, their own account may save you money.

4. 4

   Consider the EnBW mobility+ tariff you are on

   EnBW offers different tariffs (with and without a monthly fee). The tariff with a monthly fee usually gives lower per-kWh rates. In the app, go to your profile to check which tariff you are on and whether switching would save you money based on your usage.

5. 5

   Watch for idle fees and blocking fees

   Some chargers accessed through EnBW mobility+ charge a per-minute fee after your car finishes charging but the cable is still plugged in. Move your car promptly once charging is complete to avoid these fees.

App not loading charger details

You tap on a charger pin on the map and the detail screen is blank, shows a loading spinner forever, or displays outdated information. You cannot see pricing, availability, or the start button.

Symptoms

• Charger detail page shows a permanent loading spinner
• Availability status not updating (shows 'Available' for hours at a busy station)
• Price information missing from the detail screen
• App shows 'No connection' error when loading charger details

How to Fix It

1. 1

   Check your phone's internet connection

   Charging stations are often in areas with poor cellular coverage, like parking garages, highway rest stops behind concrete walls, or rural areas. Switch between mobile data and Wi-Fi, or walk to a spot with better signal and load the charger details there.

2. 2

   Force-close the app and reopen it

   Swipe the EnBW mobility+ app away from your recent apps list, wait a few seconds, and reopen it. Navigate to the charger again. This clears any stuck network requests.

3. 3

   Search for the charger by ID

   Instead of tapping the map pin, use the search bar in the app and enter the charger's ID or EVSE number (printed on the physical unit). This sometimes loads details that the map view fails to fetch.

4. 4

   Use the QR code on the charger as a backup

   Many chargers have a QR code that opens a direct session start page. Scan it with your phone camera. This page is served by the CPO, not EnBW, and often loads faster.

5. 5

   Clear the app cache

   On Android: Settings, Apps, EnBW mobility+, Storage, Clear Cache. On iOS: delete and reinstall the app (iOS does not offer cache clearing). This resolves issues caused by corrupted local data.

QR code scan not working

You scan the QR code on the charger with the EnBW mobility+ app and it either does not recognize the code, opens a wrong page, or shows an error.

Symptoms

• App says 'QR code not recognized' after scanning
• QR code opens a web page for the CPO's own app instead of EnBW mobility+
• Camera does not focus on the QR code (too dark, code damaged)
• Scan succeeds but the session start page shows an error

How to Fix It

1. 1

   Use the EnBW app's built-in scanner, not your phone camera

   Open the EnBW mobility+ app and use its QR scanner (usually in the top menu or via a scan button on the map screen). Scanning with your phone camera might open the CPO's own page instead of routing through EnBW.

2. 2

   Clean the QR code

   Wipe dirt, rain, or ice off the QR code with your sleeve. Damaged or faded QR codes are common on outdoor chargers. If the code is badly worn, look for a second QR code on a different part of the charger.

3. 3

   Turn on your phone's flashlight

   In dark or shaded areas, the camera cannot read the code. Most QR scanners (including EnBW's) have a flashlight toggle. Enable it for better readability.

4. 4

   Enter the charger ID manually

   If the QR code will not scan, look for the charger's numeric or alphanumeric ID printed nearby. Enter it manually in the EnBW app's search function to find and start the session.

Cannot stop the session from the app

You tap 'Stop Charging' in the EnBW mobility+ app and nothing happens. The session keeps running, your car keeps charging (or has already finished but the session stays active), and you want to unplug and leave.

Symptoms

• 'Stop' button in the app does not respond or shows an error
• Session shows as active in the app even after unplugging
• Charger screen says 'Session active' but your car is full
• You are worried about accumulating idle fees

How to Fix It

1. 1

   Physically unplug the connector from your car

   On most chargers, unplugging the cable ends the session automatically, regardless of what the app says. Unlock your car's charge port (from the car's screen, key fob, or charge port button) and remove the connector.

2. 2

   Wait 2 minutes and check the app again

   There is often a delay between physically ending the session and the app updating. The app depends on the CPO's system sending a 'session ended' signal back through the roaming chain. Give it a moment.

3. 3

   Force-close and reopen the app

   Sometimes the app's session view gets stuck. Force-close it, reopen, and check your session history. The session may already be ended on the backend even if the active session screen was not updating.

4. 4

   Press the stop button on the charger itself

   Many chargers have a physical stop button on the screen or housing. Press it. This sends the stop command directly to the charger hardware without going through the roaming network.

5. 5

   Contact support if you are being billed for a stuck session

   If the session stays 'active' in the app for more than 10 minutes after you have unplugged and driven away, contact EnBW mobility+ support. They can close the session on their end and correct any overcharges.

App is in German and hard to navigate

The EnBW mobility+ app defaults to German. If you do not speak German, navigating menus, understanding pricing details, and finding settings can be frustrating.

Symptoms

• All menus and buttons are in German after installation
• Language setting not obvious in the app
• Error messages appear in German, making troubleshooting difficult
• Pricing terms and tariff explanations are only in German

How to Fix It

1. 1

   Change your phone's system language temporarily

   The EnBW mobility+ app follows your phone's system language. If English is available in the app, switching your phone to English (Settings, General, Language) will switch the app too. You can switch back after you finish.

2. 2

   Check for an English option in the app settings

   Open the app, tap the profile or menu icon (usually three lines or a person icon in the corner), and look for 'Sprache' (Language) or 'Einstellungen' (Settings). Some versions offer English as an option directly.

3. 3

   Use your phone's translate feature on screenshots

   On iOS, take a screenshot and use Live Text to translate. On Android, use Google Lens. This is useful for understanding pricing details or error messages in German.

4. 4

   Consider an alternative roaming app with better language support

   If the language barrier is a persistent problem, apps like Shell Recharge, Plugsurfing, or Chargemap offer similar roaming coverage across Europe and have full English interfaces. They access many of the same chargers.