Tesla Model S Charging at EnBW mobility+

Tesla Model S Charger Will Not Start a Session

You plugged in your Model S and nothing is happening. No green light on the charge port, no animation on the 17-inch touchscreen, just silence. Whether you are at a Supercharger, a third-party CCS2 station, or a home wallbox, there are a handful of common reasons the session will not begin.

Symptoms

• Charge port LED stays white or flashes red after plugging in the connector
• 17-inch touchscreen shows no charging animation or displays an error message
• Supercharger stall makes a click but does not begin delivering power
• CCS2 connector at a third-party station locks in but charging never starts
• Tesla app shows 'Not Charging' even though the cable is connected

What to Do

1. 1

   Check the charge port LED color

   Walk to the left rear of the car and look at the charge port light. White means ready but not connected. Blue means communicating. Green means charging. Red or amber means there is a fault. If it is white with the cable plugged in, remove and reseat the connector firmly.

2. 2

   Unplug and replug the connector

   Remove the connector completely, wait five seconds, then reinsert it until you hear the latch click. On CCS2 connectors, make sure both the top (AC pins) and bottom (DC pins) sections are seated properly.

3. 3

   Check for scheduled charging on the touchscreen

   On the 17-inch touchscreen, go to Controls, then Charging. If scheduled charging is active, you will see the planned start time. Tap to disable it or select 'Charge Now' to override the schedule.

4. 4

   Authorize the session at non-Tesla chargers

   At third-party CCS2 stations, check whether the charger requires you to start the session through an app, RFID card, or contactless payment. Plug & Charge works at supported stations, but many still require manual authorization.

5. 5

   Try a different stall or charger

   If you are at a Supercharger, move to a different stall. If you are at a third-party station, try the other connector. A faulted charger looks identical to a working one from the outside.

6. 6

   Restart the touchscreen

   Hold both scroll wheels on the steering wheel for about 10 seconds until the 17-inch touchscreen goes black and reboots. This resets the charging controller and fixes some communication glitches. The car stays on during the reboot.

Tesla Model S Payment Failed at Charging Station

You are plugged in and the charger is waiting for payment, or the Supercharger session will not start because of a billing issue. Payment problems are one of the most common reasons drivers get stuck at chargers, and the Model S has multiple ways to pay depending on where you are charging.

Symptoms

• Supercharger session will not start and the Tesla app shows a payment error
• Third-party CCS2 charger displays 'Authorization failed' after tapping your card
• RFID card is not recognized by the charger's reader
• Plug & Charge does not activate at a supported station
• Contactless bank card is rejected by the charger's payment terminal

What to Do

1. 1

   Check your Tesla account payment method

   Open the Tesla app on your phone. Go to Account, then Payment. Verify your credit card is current and has not expired. If the card was replaced, update the details. Supercharger sessions will not start without a valid payment method on file.

2. 2

   Try a different payment method at the charger

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having at least two payment methods gives you a backup when one does not work.

3. 3

   Scan the charger QR code for browser payment

   Most public chargers have a QR code on the unit. Scanning it with your phone opens the operator's payment page in your browser. You can usually pay with a credit card directly without downloading their app.

4. 4

   Check your banking app for blocked transactions

   Open your banking app and look for flagged or declined transactions. Some banks require you to approve the charge manually. Approve it and retry the payment at the charger.

5. 5

   Try Plug & Charge by replugging

   If the charger supports Plug & Charge, unplug the CCS2 connector from your Model S, wait a few seconds, and replug. Payment should authorize automatically through the cable. This only works if your Tesla account has Plug & Charge enabled and the charger supports ISO 15118.

6. 6

   Move to a Supercharger or a different station

   If you cannot resolve the payment issue, find a Tesla Supercharger using the nav on the 17-inch touchscreen. Supercharger billing is handled entirely through your Tesla account, bypassing third-party payment systems.

Tesla Model S Charging Slower Than Expected at Charger

You pulled into a Supercharger expecting 250 kW and the 17-inch touchscreen shows 80 kW. Or your home wallbox is crawling at 3 kW instead of 11 kW. The Model S has one of the fastest charging curves on the road, but reaching peak speed depends on battery temperature, state of charge, and a few settings you can check in under a minute.

Symptoms

• DC fast charging power well below 250 kW on the touchscreen despite a rated charger
• AC home charging stuck at 3-4 kW instead of the expected 11 kW on 3-phase
• Charging speed drops sharply after 40-50% on the touchscreen during DC fast charging
• Supercharger shows significantly lower kW than neighboring stalls
• Non-Tesla CCS2 charger delivers far less power than its rated maximum

What to Do

1. 1

   Check if the battery was preconditioned

   On the 17-inch touchscreen, tap the charging icon. If you see a snowflake icon or a message about conditioning, the battery was not warm enough when you arrived. Next time, navigate to the charger using Tesla nav at least 20-30 minutes before arrival so preconditioning kicks in automatically.

2. 2

   Check your current state of charge

   If you are above 50%, the slower speed is expected on the 95 kWh NCA pack. Peak power happens roughly between 5-30%. For the fastest charging stops on a road trip, arrive between 10-20%.

3. 3

   Move to an unpaired Supercharger stall

   Look at the stall numbers. If they are labeled in A/B pairs (3A/3B, 4A/4B), pick a stall where the paired stall is empty. At V3 or V4 Superchargers with the Magic Dock or the new V4 cable, this is not a concern.

4. 4

   Check the AC charge current limit on the touchscreen

   Go to Controls, then Charging on the touchscreen. Look for the charge current setting. Make sure it is set to the maximum amperage. This only affects AC charging at home or destination chargers, not Supercharging.

5. 5

   Try a different charger or stall

   If speeds remain low, the charger hardware may be degraded. Try another stall at the same location. On non-Tesla CCS2 stations, check the charger display for error codes or reduced power notices.

6. 6

   Check for a Tesla software update

   Go to Controls, then Software on the touchscreen. If an update is pending, install it. Tesla has adjusted charging curves through over-the-air updates in the past, sometimes improving peak speeds.

Roaming pricing unclear or higher than expected

You started a session through EnBW mobility+ and the per-kWh price was significantly higher than you expected. The same charger costs different amounts at different times, and the pricing logic feels opaque.

Symptoms

• Per-kWh rate on the receipt is higher than the rate shown on the EnBW website
• Same charger location costs more through EnBW mobility+ than through the CPO's own app
• Price differs between two chargers at the same station
• Unexpected 'roaming fee' or 'session fee' on your invoice

How to Fix It

1. 1

   Check the price before you start the session

   In the EnBW mobility+ app, tap on the charger and look for the pricing details before starting. The app shows the per-kWh rate for that specific charger. Prices vary because each CPO sets different roaming rates.

2. 2

   Understand the pricing tiers

   EnBW mobility+ groups chargers into pricing tiers. 'EnBW own' chargers are cheapest, 'roaming standard' is mid-range, and 'roaming plus' (typically high-power chargers from premium CPOs like Ionity) costs more. The tier is usually shown in the charger details.

3. 3

   Compare with the CPO's own app

   If a charger is operated by Ionity, for example, check the Ionity app or website for their direct pricing. Sometimes the CPO's own app or RFID card is cheaper because there is no roaming middleman. If you use that CPO frequently, their own account may save you money.

4. 4

   Consider the EnBW mobility+ tariff you are on

   EnBW offers different tariffs (with and without a monthly fee). The tariff with a monthly fee usually gives lower per-kWh rates. In the app, go to your profile to check which tariff you are on and whether switching would save you money based on your usage.

5. 5

   Watch for idle fees and blocking fees

   Some chargers accessed through EnBW mobility+ charge a per-minute fee after your car finishes charging but the cable is still plugged in. Move your car promptly once charging is complete to avoid these fees.

App not loading charger details

You tap on a charger pin on the map and the detail screen is blank, shows a loading spinner forever, or displays outdated information. You cannot see pricing, availability, or the start button.

Symptoms

• Charger detail page shows a permanent loading spinner
• Availability status not updating (shows 'Available' for hours at a busy station)
• Price information missing from the detail screen
• App shows 'No connection' error when loading charger details

How to Fix It

1. 1

   Check your phone's internet connection

   Charging stations are often in areas with poor cellular coverage, like parking garages, highway rest stops behind concrete walls, or rural areas. Switch between mobile data and Wi-Fi, or walk to a spot with better signal and load the charger details there.

2. 2

   Force-close the app and reopen it

   Swipe the EnBW mobility+ app away from your recent apps list, wait a few seconds, and reopen it. Navigate to the charger again. This clears any stuck network requests.

3. 3

   Search for the charger by ID

   Instead of tapping the map pin, use the search bar in the app and enter the charger's ID or EVSE number (printed on the physical unit). This sometimes loads details that the map view fails to fetch.

4. 4

   Use the QR code on the charger as a backup

   Many chargers have a QR code that opens a direct session start page. Scan it with your phone camera. This page is served by the CPO, not EnBW, and often loads faster.

5. 5

   Clear the app cache

   On Android: Settings, Apps, EnBW mobility+, Storage, Clear Cache. On iOS: delete and reinstall the app (iOS does not offer cache clearing). This resolves issues caused by corrupted local data.

QR code scan not working

You scan the QR code on the charger with the EnBW mobility+ app and it either does not recognize the code, opens a wrong page, or shows an error.

Symptoms

• App says 'QR code not recognized' after scanning
• QR code opens a web page for the CPO's own app instead of EnBW mobility+
• Camera does not focus on the QR code (too dark, code damaged)
• Scan succeeds but the session start page shows an error

How to Fix It

1. 1

   Use the EnBW app's built-in scanner, not your phone camera

   Open the EnBW mobility+ app and use its QR scanner (usually in the top menu or via a scan button on the map screen). Scanning with your phone camera might open the CPO's own page instead of routing through EnBW.

2. 2

   Clean the QR code

   Wipe dirt, rain, or ice off the QR code with your sleeve. Damaged or faded QR codes are common on outdoor chargers. If the code is badly worn, look for a second QR code on a different part of the charger.

3. 3

   Turn on your phone's flashlight

   In dark or shaded areas, the camera cannot read the code. Most QR scanners (including EnBW's) have a flashlight toggle. Enable it for better readability.

4. 4

   Enter the charger ID manually

   If the QR code will not scan, look for the charger's numeric or alphanumeric ID printed nearby. Enter it manually in the EnBW app's search function to find and start the session.

Cannot stop the session from the app

You tap 'Stop Charging' in the EnBW mobility+ app and nothing happens. The session keeps running, your car keeps charging (or has already finished but the session stays active), and you want to unplug and leave.

Symptoms

• 'Stop' button in the app does not respond or shows an error
• Session shows as active in the app even after unplugging
• Charger screen says 'Session active' but your car is full
• You are worried about accumulating idle fees

How to Fix It

1. 1

   Physically unplug the connector from your car

   On most chargers, unplugging the cable ends the session automatically, regardless of what the app says. Unlock your car's charge port (from the car's screen, key fob, or charge port button) and remove the connector.

2. 2

   Wait 2 minutes and check the app again

   There is often a delay between physically ending the session and the app updating. The app depends on the CPO's system sending a 'session ended' signal back through the roaming chain. Give it a moment.

3. 3

   Force-close and reopen the app

   Sometimes the app's session view gets stuck. Force-close it, reopen, and check your session history. The session may already be ended on the backend even if the active session screen was not updating.

4. 4

   Press the stop button on the charger itself

   Many chargers have a physical stop button on the screen or housing. Press it. This sends the stop command directly to the charger hardware without going through the roaming network.

5. 5

   Contact support if you are being billed for a stuck session

   If the session stays 'active' in the app for more than 10 minutes after you have unplugged and driven away, contact EnBW mobility+ support. They can close the session on their end and correct any overcharges.

App is in German and hard to navigate

The EnBW mobility+ app defaults to German. If you do not speak German, navigating menus, understanding pricing details, and finding settings can be frustrating.

Symptoms

• All menus and buttons are in German after installation
• Language setting not obvious in the app
• Error messages appear in German, making troubleshooting difficult
• Pricing terms and tariff explanations are only in German

How to Fix It

1. 1

   Change your phone's system language temporarily

   The EnBW mobility+ app follows your phone's system language. If English is available in the app, switching your phone to English (Settings, General, Language) will switch the app too. You can switch back after you finish.

2. 2

   Check for an English option in the app settings

   Open the app, tap the profile or menu icon (usually three lines or a person icon in the corner), and look for 'Sprache' (Language) or 'Einstellungen' (Settings). Some versions offer English as an option directly.

3. 3

   Use your phone's translate feature on screenshots

   On iOS, take a screenshot and use Live Text to translate. On Android, use Google Lens. This is useful for understanding pricing details or error messages in German.

4. 4

   Consider an alternative roaming app with better language support

   If the language barrier is a persistent problem, apps like Shell Recharge, Plugsurfing, or Chargemap offer similar roaming coverage across Europe and have full English interfaces. They access many of the same chargers.