Volvo EX40 Charging at Shell Recharge

Volvo EX40 Plugged In but the Charger Will Not Start

You plugged the cable into your Volvo EX40 and nothing happens. No charging animation on the center screen, no LED on the charger, or the charger shows an error. This is one of the most common frustrations at public chargers and is usually caused by authentication, the charge port, or the charger itself.

Symptoms

• Charger displays an error code or flashing red light after plugging in
• Charge port LED on the EX40 does not turn on or stays amber
• Google Built-In display shows no active charging session
• Charger screen says 'waiting for vehicle' or 'authentication failed'
• Cable is plugged in but the connector does not lock into the charge port

What to Do

1. 1

   Check if authentication is required

   Look at the charger's screen. Most public chargers need you to tap an RFID card, scan a QR code, or start the session through an app before charging begins. Plug & Charge works on some networks but not all.

2. 2

   Open the charge port fully

   Make sure the charge port door on the left rear of your EX40 is fully open. Press the edge of the door to release it if it is stuck. Clear any ice or debris in cold weather.

3. 3

   Push the connector in firmly

   Insert the CCS connector straight into the port and push until you hear a click. The connector should lock in place. If it will not lock, do not force it. Check for debris in the port.

4. 4

   Disable scheduled charging

   On the center display, go to Settings, then Charging. Check if a charging schedule is active. Turn it off or set it to 'charge immediately' to start charging at a public charger.

5. 5

   Unplug and try again

   Disconnect the cable, wait 10 seconds, and plug in again. Sometimes the communication handshake between car and charger fails on the first attempt and a retry resolves it.

6. 6

   Try a different charger or connector

   If the charger still will not start, move to a different stall or station. The charger may have an internal fault even if no error is displayed.

Volvo EX40 Charger Payment Failed or Card Declined

You are standing at a charger with your Volvo EX40, ready to charge, and the payment does not go through. Your card is declined, the app shows an error, or you cannot figure out how to pay at all. Payment problems at public chargers are one of the most common frustrations and usually have nothing to do with your car.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Charging app shows an error when trying to start a session
• No visible way to pay at the charger
• Contactless payment terminal does not respond to your card or phone
• Plug & Charge does not activate and the charger waits for payment

What to Do

1. 1

   Check if Plug & Charge is active

   Open the Volvo Cars app and check if Plug & Charge is enabled and linked to a payment method. If it is active, try unplugging and replugging the connector. Plug & Charge works only on supported networks.

2. 2

   Try a different payment method

   If your card was declined, try a different card, your phone's mobile wallet, or the charger network's app. Many chargers accept multiple payment options.

3. 3

   Check your card for pre-authorization holds

   Open your banking app and check for pending charges. If there are multiple holds from earlier charging attempts, your available balance may be too low. Call your bank to release them if needed.

4. 4

   Download the charger network's app

   Look at the charger for the network name or logo. Download their app, create an account, add a payment method, and start the session through the app instead of the charger's payment terminal.

5. 5

   Use an RFID charging card

   If you have an RFID card from a charging provider, tap it on the charger's reader. RFID cards work even when apps and contactless terminals fail. They are a reliable backup.

Volvo EX40 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX40 expecting 150 kW and the center screen shows 30 kW. Or your home wallbox is stuck at 3 kW instead of 11 kW. Slow charging on the EX40 is almost never a defect. It is usually the battery temperature, the charger itself, or a setting in the Volvo Cars app you can fix quickly.

Symptoms

• DC fast charging speed well below the 150 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 50-60%
• Google Built-In display shows lower power than the charger's rating
• Charging session starts at a reasonable speed but slows within minutes

What to Do

1. 1

   Check the battery temperature on the display

   Look at the charging screen on the EX40's center display (Google Built-In). If the battery is cold, drive for 15-20 minutes before charging or use the Volvo Cars app to start preconditioning before you arrive.

2. 2

   Use navigation to precondition the battery

   Set the charger as your destination in Google Maps on the center screen. The EX40 will automatically precondition the battery during the drive so it reaches optimal temperature for fast charging.

3. 3

   Check your state of charge

   If you are above 80%, the slower speed is normal. For fastest DC charging, arrive between 10-20% and charge to 80%. The last 20% takes as long as the first 80%.

4. 4

   Verify the charger is not sharing power

   Look at the charging unit. If there are two cables and someone is using the other one, you are likely sharing power. Move to a charger where both stalls are free.

5. 5

   Check the AC charge current setting

   In the EX40's settings menu, check that the charge current limiter is set to maximum. A reduced setting limits AC charging speed and is sometimes changed accidentally.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded. Try a different connector at the same station, or drive to another charging location.

RFID card not recognized at the charger

You tap your Shell Recharge RFID card on the charger's reader but it does not respond, beeps an error, or shows 'Card not recognized.'

Symptoms

• Charger beeps but displays 'Unknown card' or 'Authorization failed'
• No response at all when tapping the card
• Card works at some stations but not others
• Card worked yesterday at the same charger but does not work today

How to Fix It

1. 1

   Hold the card still on the reader for 3 to 5 seconds

   RFID readers at some chargers are slow. Do not tap and remove quickly. Hold the card flat against the reader and wait for a confirmation beep or screen change.

2. 2

   Check that your RFID card is activated

   New Shell Recharge RFID cards must be activated in the Shell Recharge app before first use. Go to the app, find the RFID section, and make sure the card status shows active.

3. 3

   Try starting the session through the app instead

   Open the Shell Recharge app, find the station, select the charger, and start the session digitally. This bypasses the RFID reader entirely and uses the roaming connection.

4. 4

   Check if the CPO supports Shell Recharge roaming

   Not every charger that appears in the Shell Recharge app accepts the Shell Recharge RFID card. Some chargers only accept app-based roaming. The station details in the app usually indicate which payment methods are supported.

5. 5

   Clean the card and try again

   Dirt, scratches, or a phone case between the card and reader can block the RFID signal. Remove the card from any holder, wipe it, and try again on the reader's sweet spot (often marked with a contactless symbol).

Roaming vs direct pricing confusion

The price you pay through Shell Recharge is different from the price shown on the charger's screen. This is because Shell Recharge adds a roaming markup on top of the CPO's base rate.

Symptoms

• Charger screen shows 0.39 EUR/kWh but Shell Recharge bills 0.55 EUR/kWh
• Invoice includes fees not displayed at the charger (session fee, per-minute fee)
• Same station is cheaper when using the CPO's own app
• Pricing in the Shell Recharge app does not match the final invoice

How to Fix It

1. 1

   Check the Shell Recharge app for the roaming price before starting

   Before you tap your card or start a session, open the Shell Recharge app and select the station. The app shows the Shell Recharge price, which includes any roaming fee. This is the price you will actually pay.

2. 2

   Understand the pricing structure

   Shell Recharge typically charges a per-kWh rate plus sometimes a session start fee or per-minute fee. The charger screen shows the CPO's direct price, not the roaming price. These are two different rates for two different billing relationships.

3. 3

   Consider using the CPO's own app for lower rates

   If you charge at the same network regularly (for example, Allego, Fastned, or EnBW), their own app usually offers a lower price than roaming through Shell Recharge. The trade-off is managing multiple apps.

4. 4

   Download your invoice from the Shell Recharge app

   Go to your charging history in the Shell Recharge app. Each session has a detailed breakdown showing energy delivered, per-kWh rate, session fees, and total cost. Compare this with what you expected.

Session not starting via QR code

You scan the QR code on the charger to start a session through the Shell Recharge app, but nothing happens or you get an error.

Symptoms

• QR code opens the Shell Recharge app but shows 'Station not found'
• QR code opens a web page instead of the app
• App shows 'Unable to start session' after scanning
• QR code is faded, damaged, or partially covered by a sticker

How to Fix It

1. 1

   Search for the station manually in the app

   If the QR code does not work, open the Shell Recharge app, search for the station by name or location, and start the session from the station page. You may need to select the specific connector or charger ID.

2. 2

   Check the charger ID number

   Every charger has an ID printed somewhere on the unit (usually near the QR code or on a label). Enter this ID manually in the Shell Recharge app if the QR scan fails.

3. 3

   Make sure the QR code belongs to Shell Recharge

   Many chargers have multiple QR codes from different roaming providers and the CPO itself. Make sure you are scanning the Shell Recharge QR code, not the CPO's own code. Scanning the wrong code opens the wrong app or website.

4. 4

   Try the RFID card or contactless payment instead

   QR code start is just one method. Tap your Shell Recharge RFID card or use contactless payment if the charger supports it.

5. 5

   Check your internet connection

   Starting a session via QR code requires the app to communicate with Shell Recharge's servers and the CPO's backend. If you have weak mobile signal (common at highway rest stops), the request may time out. Try switching between Wi-Fi and mobile data.

App showing wrong charger status

The Shell Recharge app shows a charger as available, occupied, or offline, but the actual status is different when you arrive.

Symptoms

• App shows 'Available' but the charger is out of order or has an error screen
• App shows 'Occupied' but no vehicle is connected
• Status has not updated for hours and seems stale
• App shows fewer chargers at a station than physically exist

How to Fix It

1. 1

   Understand that status data is delayed

   Shell Recharge gets charger status from the CPO's systems through the roaming connection. This data can lag by 5 to 15 minutes. A charger that just became available may still show as occupied in the app.

2. 2

   Try plugging in regardless of app status

   If you are already at the station and a charger looks physically available (no vehicle connected, no error on screen), try plugging in and starting a session. The real-time status at the charger overrides whatever the app shows.

3. 3

   Check the CPO's own app for more accurate status

   The CPO (the company that actually operates the charger) usually has more accurate real-time status than roaming aggregators like Shell Recharge. If accuracy matters, cross-check with the CPO's app or website.

4. 4

   Report the incorrect status

   Use the Shell Recharge app to report the charger issue. This helps improve status accuracy over time.

Billing discrepancy between Shell Recharge and the CPO

The amount billed by Shell Recharge does not match what you expected based on the energy delivered or the session duration. This can happen because of how roaming billing works.

Symptoms

• Billed for more kWh than your vehicle's dashboard shows
• Charged a session fee you did not expect
• Per-minute idle fee added even though you unplugged on time
• Double charge: both Shell Recharge and the CPO billed you

How to Fix It

1. 1

   Compare the Shell Recharge invoice with your vehicle's data

   Your vehicle's dashboard shows how much energy the battery received. The charger meters how much energy it delivered, which includes conversion losses. A 5 to 10% difference is normal.

2. 2

   Check for per-minute fees

   Some CPOs charge a per-minute fee (for time spent connected) on top of the per-kWh fee. This can be especially costly during slow AC charging sessions. Check the pricing breakdown in the Shell Recharge app.

3. 3

   Look for session or start fees

   Some stations add a fixed fee per session (for example, 0.35 EUR to 1.00 EUR). This appears in the Shell Recharge invoice as a separate line item.

4. 4

   Dispute the charge through the Shell Recharge app

   If the amount is clearly wrong (double billed, charged for a session that never started, or obviously excessive), contact Shell Recharge support through the app. Go to your charging history, select the session, and use the dispute or help option.

5. 5

   Keep your vehicle's charge data as evidence

   Take a photo of your vehicle's charging screen or dashboard showing the kWh received and the session duration. This is useful if you need to dispute a charge.