Volvo EX40 Charging at Recharge

Volvo EX40 Plugged In but the Charger Will Not Start

You plugged the cable into your Volvo EX40 and nothing happens. No charging animation on the center screen, no LED on the charger, or the charger shows an error. This is one of the most common frustrations at public chargers and is usually caused by authentication, the charge port, or the charger itself.

Symptoms

• Charger displays an error code or flashing red light after plugging in
• Charge port LED on the EX40 does not turn on or stays amber
• Google Built-In display shows no active charging session
• Charger screen says 'waiting for vehicle' or 'authentication failed'
• Cable is plugged in but the connector does not lock into the charge port

What to Do

1. 1

   Check if authentication is required

   Look at the charger's screen. Most public chargers need you to tap an RFID card, scan a QR code, or start the session through an app before charging begins. Plug & Charge works on some networks but not all.

2. 2

   Open the charge port fully

   Make sure the charge port door on the left rear of your EX40 is fully open. Press the edge of the door to release it if it is stuck. Clear any ice or debris in cold weather.

3. 3

   Push the connector in firmly

   Insert the CCS connector straight into the port and push until you hear a click. The connector should lock in place. If it will not lock, do not force it. Check for debris in the port.

4. 4

   Disable scheduled charging

   On the center display, go to Settings, then Charging. Check if a charging schedule is active. Turn it off or set it to 'charge immediately' to start charging at a public charger.

5. 5

   Unplug and try again

   Disconnect the cable, wait 10 seconds, and plug in again. Sometimes the communication handshake between car and charger fails on the first attempt and a retry resolves it.

6. 6

   Try a different charger or connector

   If the charger still will not start, move to a different stall or station. The charger may have an internal fault even if no error is displayed.

Volvo EX40 Charger Payment Failed or Card Declined

You are standing at a charger with your Volvo EX40, ready to charge, and the payment does not go through. Your card is declined, the app shows an error, or you cannot figure out how to pay at all. Payment problems at public chargers are one of the most common frustrations and usually have nothing to do with your car.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Charging app shows an error when trying to start a session
• No visible way to pay at the charger
• Contactless payment terminal does not respond to your card or phone
• Plug & Charge does not activate and the charger waits for payment

What to Do

1. 1

   Check if Plug & Charge is active

   Open the Volvo Cars app and check if Plug & Charge is enabled and linked to a payment method. If it is active, try unplugging and replugging the connector. Plug & Charge works only on supported networks.

2. 2

   Try a different payment method

   If your card was declined, try a different card, your phone's mobile wallet, or the charger network's app. Many chargers accept multiple payment options.

3. 3

   Check your card for pre-authorization holds

   Open your banking app and check for pending charges. If there are multiple holds from earlier charging attempts, your available balance may be too low. Call your bank to release them if needed.

4. 4

   Download the charger network's app

   Look at the charger for the network name or logo. Download their app, create an account, add a payment method, and start the session through the app instead of the charger's payment terminal.

5. 5

   Use an RFID charging card

   If you have an RFID card from a charging provider, tap it on the charger's reader. RFID cards work even when apps and contactless terminals fail. They are a reliable backup.

Volvo EX40 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX40 expecting 150 kW and the center screen shows 30 kW. Or your home wallbox is stuck at 3 kW instead of 11 kW. Slow charging on the EX40 is almost never a defect. It is usually the battery temperature, the charger itself, or a setting in the Volvo Cars app you can fix quickly.

Symptoms

• DC fast charging speed well below the 150 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 50-60%
• Google Built-In display shows lower power than the charger's rating
• Charging session starts at a reasonable speed but slows within minutes

What to Do

1. 1

   Check the battery temperature on the display

   Look at the charging screen on the EX40's center display (Google Built-In). If the battery is cold, drive for 15-20 minutes before charging or use the Volvo Cars app to start preconditioning before you arrive.

2. 2

   Use navigation to precondition the battery

   Set the charger as your destination in Google Maps on the center screen. The EX40 will automatically precondition the battery during the drive so it reaches optimal temperature for fast charging.

3. 3

   Check your state of charge

   If you are above 80%, the slower speed is normal. For fastest DC charging, arrive between 10-20% and charge to 80%. The last 20% takes as long as the first 80%.

4. 4

   Verify the charger is not sharing power

   Look at the charging unit. If there are two cables and someone is using the other one, you are likely sharing power. Move to a charger where both stalls are free.

5. 5

   Check the AC charge current setting

   In the EX40's settings menu, check that the charge current limiter is set to maximum. A reduced setting limits AC charging speed and is sometimes changed accidentally.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded. Try a different connector at the same station, or drive to another charging location.

Charger stuck in "preparing" state

You authenticated successfully, the charger says "preparing," but it never starts delivering power. This is one of the most reported issues on Recharge stations, especially at older units.

Symptoms

• Charger screen shows "Preparing" or "Initializing" for more than two minutes
• Your car's charging indicator does not activate
• The Recharge app shows the session as active but 0 kW delivered
• The charger fan spins up but no power flows

How to Fix It

1. 1

   Wait up to three minutes

   Some Recharge units, particularly the 300kW stations, take longer to complete the power handshake with your car. Give it a full three minutes before taking action.

2. 2

   Unplug and reconnect

   Remove the CCS2 connector, wait 15 seconds, then plug it back in firmly. This resets the communication between your car and the charger.

3. 3

   Stop the session in the Recharge app and start a new one

   Open the Recharge app, tap Stop on the active session, wait for it to fully end, then start a new session on the same charger. This clears any stuck state on the backend.

4. 4

   Try the other connector on the same unit

   Many Recharge stations have two CCS2 connectors. If one is stuck, the other connector on the same unit often works fine.

5. 5

   Use a different authentication method

   If you started with the app, try your RFID card instead, or vice versa. Sometimes the issue is with the authentication path, not the charger hardware.

Old Fortum branding causes app scan failure

Recharge was originally part of Fortum's charging operations before being spun off as a separate company. Some older stations still display Fortum logos and QR codes. Scanning an old Fortum QR code with the Recharge app may not work, or it may redirect to a dead Fortum page.

Symptoms

• QR code on the charger opens a Fortum website or shows an error
• Recharge app says "Charger not found" after scanning
• Station ID on the physical unit does not match what the Recharge app expects
• The charger has Fortum branding but is listed as Recharge in third-party apps

How to Fix It

1. 1

   Ignore the QR code and search by station name in the Recharge app

   Open the Recharge app, use the map or search to find the station by location. The charger will appear under its Recharge name even if the physical unit still says Fortum.

2. 2

   Enter the charger ID manually

   Look for a numeric ID on the charger, often printed on a sticker near the connector. In the Recharge app, tap "Enter ID" and type it in directly.

3. 3

   Use RFID or contactless payment instead of the app

   Tap your Recharge RFID card or a contactless bank card on the reader. This bypasses the app entirely and works regardless of the branding on the charger.

4. 4

   Check if contactless is available on this unit

   Not all Recharge stations support contactless bank card payment. Look for a card reader terminal on the charger. If there is no terminal, you will need the app or an RFID card.

RFID card from old Fortum account not recognized

If you had a Fortum Charge & Drive account and RFID card, it may not work automatically on the Recharge network. Some cards were migrated, others were not.

Symptoms

• Tapping your old Fortum RFID card shows "Card not recognized" on the charger
• The charger beeps but does not start a session
• Your Fortum card works on some stations but not others

How to Fix It

1. 1

   Log in to the Recharge app and check your RFID cards

   Open the Recharge app, go to your account settings, and look under RFID cards. If your old Fortum card is not listed, it was not migrated automatically.

2. 2

   Re-register your RFID card

   In the Recharge app, tap "Add RFID card" and follow the steps. You will need the card number printed on the back of your RFID card.

3. 3

   Use the app to start the session while you wait for RFID activation

   RFID card registration can take up to 24 hours to propagate across all stations. Use the app to authenticate in the meantime.

4. 4

   Order a new Recharge RFID card if re-registration fails

   Some older Fortum cards use a chip format that is not compatible. You can order a new Recharge RFID card through the app or website.

Contactless payment not accepted

You are trying to tap your bank card or phone to pay, but the charger does not respond or shows an error. Contactless payment availability varies across Recharge stations.

Symptoms

• No card reader terminal visible on the charger
• Card reader shows "Payment failed" or does not respond to taps
• Apple Pay or Google Pay not recognized
• The charger prompts for an RFID card but you only have a bank card

How to Fix It

1. 1

   Check if this station supports contactless payment

   Look for a separate payment terminal with a contactless symbol. Not all Recharge stations have been upgraded. The Recharge app shows payment options for each station on the station detail page.

2. 2

   Try removing and re-holding your card

   Hold your card flat against the reader for at least three seconds. Some terminals need a longer hold than you might expect. Remove the card fully, then try again.

3. 3

   Fall back to the Recharge app

   If contactless is not working, open the Recharge app and start the session from there. You need a payment method saved in the app.

4. 4

   Try a different card

   Some Visa Electron and certain prepaid cards are not accepted by the payment terminals. A standard Visa or Mastercard debit or credit card usually works.

Charging speed much lower than expected

The station is rated for 300kW, but your car is only pulling 50kW or less. While your car's battery management limits the maximum speed, Recharge stations can also throttle power.

Symptoms

• Charger display shows far less power than the station's rated capacity
• Charging speed drops suddenly mid-session
• Other cars at the same station are also charging slowly
• The Recharge app shows the session but at low power

How to Fix It

1. 1

   Check how many other cars are charging at the same station

   Recharge stations with multiple connectors often share a power cabinet. If two or three cars are charging simultaneously, the available power per car drops. This is normal and not a fault.

2. 2

   Check your battery level

   DC fast charging slows significantly above 80% on most EVs. If your battery is above 70-80%, the slower speed is your car protecting the battery, not a problem with the Recharge station.

3. 3

   Check the temperature

   In cold weather, your car may limit charging speed until the battery warms up. This can take 10-15 minutes of charging before speeds increase. Some cars precondition the battery if you set the charger as a destination in navigation.

4. 4

   Try a different connector at the station

   Individual connectors can have faults that limit power output. If another connector is free, unplug and try it.

5. 5

   Report the issue in the Recharge app

   If the speed is unusually low and none of the above apply, report it through the Recharge app. Tap the active session and look for a "Report issue" option. This helps Recharge identify hardware problems.