Volvo EX40 Charging at EnBW mobility+

Volvo EX40 Plugged In but the Charger Will Not Start

You plugged the cable into your Volvo EX40 and nothing happens. No charging animation on the center screen, no LED on the charger, or the charger shows an error. This is one of the most common frustrations at public chargers and is usually caused by authentication, the charge port, or the charger itself.

Symptoms

• Charger displays an error code or flashing red light after plugging in
• Charge port LED on the EX40 does not turn on or stays amber
• Google Built-In display shows no active charging session
• Charger screen says 'waiting for vehicle' or 'authentication failed'
• Cable is plugged in but the connector does not lock into the charge port

What to Do

1. 1

   Check if authentication is required

   Look at the charger's screen. Most public chargers need you to tap an RFID card, scan a QR code, or start the session through an app before charging begins. Plug & Charge works on some networks but not all.

2. 2

   Open the charge port fully

   Make sure the charge port door on the left rear of your EX40 is fully open. Press the edge of the door to release it if it is stuck. Clear any ice or debris in cold weather.

3. 3

   Push the connector in firmly

   Insert the CCS connector straight into the port and push until you hear a click. The connector should lock in place. If it will not lock, do not force it. Check for debris in the port.

4. 4

   Disable scheduled charging

   On the center display, go to Settings, then Charging. Check if a charging schedule is active. Turn it off or set it to 'charge immediately' to start charging at a public charger.

5. 5

   Unplug and try again

   Disconnect the cable, wait 10 seconds, and plug in again. Sometimes the communication handshake between car and charger fails on the first attempt and a retry resolves it.

6. 6

   Try a different charger or connector

   If the charger still will not start, move to a different stall or station. The charger may have an internal fault even if no error is displayed.

Volvo EX40 Charger Payment Failed or Card Declined

You are standing at a charger with your Volvo EX40, ready to charge, and the payment does not go through. Your card is declined, the app shows an error, or you cannot figure out how to pay at all. Payment problems at public chargers are one of the most common frustrations and usually have nothing to do with your car.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Charging app shows an error when trying to start a session
• No visible way to pay at the charger
• Contactless payment terminal does not respond to your card or phone
• Plug & Charge does not activate and the charger waits for payment

What to Do

1. 1

   Check if Plug & Charge is active

   Open the Volvo Cars app and check if Plug & Charge is enabled and linked to a payment method. If it is active, try unplugging and replugging the connector. Plug & Charge works only on supported networks.

2. 2

   Try a different payment method

   If your card was declined, try a different card, your phone's mobile wallet, or the charger network's app. Many chargers accept multiple payment options.

3. 3

   Check your card for pre-authorization holds

   Open your banking app and check for pending charges. If there are multiple holds from earlier charging attempts, your available balance may be too low. Call your bank to release them if needed.

4. 4

   Download the charger network's app

   Look at the charger for the network name or logo. Download their app, create an account, add a payment method, and start the session through the app instead of the charger's payment terminal.

5. 5

   Use an RFID charging card

   If you have an RFID card from a charging provider, tap it on the charger's reader. RFID cards work even when apps and contactless terminals fail. They are a reliable backup.

Volvo EX40 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX40 expecting 150 kW and the center screen shows 30 kW. Or your home wallbox is stuck at 3 kW instead of 11 kW. Slow charging on the EX40 is almost never a defect. It is usually the battery temperature, the charger itself, or a setting in the Volvo Cars app you can fix quickly.

Symptoms

• DC fast charging speed well below the 150 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 50-60%
• Google Built-In display shows lower power than the charger's rating
• Charging session starts at a reasonable speed but slows within minutes

What to Do

1. 1

   Check the battery temperature on the display

   Look at the charging screen on the EX40's center display (Google Built-In). If the battery is cold, drive for 15-20 minutes before charging or use the Volvo Cars app to start preconditioning before you arrive.

2. 2

   Use navigation to precondition the battery

   Set the charger as your destination in Google Maps on the center screen. The EX40 will automatically precondition the battery during the drive so it reaches optimal temperature for fast charging.

3. 3

   Check your state of charge

   If you are above 80%, the slower speed is normal. For fastest DC charging, arrive between 10-20% and charge to 80%. The last 20% takes as long as the first 80%.

4. 4

   Verify the charger is not sharing power

   Look at the charging unit. If there are two cables and someone is using the other one, you are likely sharing power. Move to a charger where both stalls are free.

5. 5

   Check the AC charge current setting

   In the EX40's settings menu, check that the charge current limiter is set to maximum. A reduced setting limits AC charging speed and is sometimes changed accidentally.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded. Try a different connector at the same station, or drive to another charging location.

Roaming pricing unclear or higher than expected

You started a session through EnBW mobility+ and the per-kWh price was significantly higher than you expected. The same charger costs different amounts at different times, and the pricing logic feels opaque.

Symptoms

• Per-kWh rate on the receipt is higher than the rate shown on the EnBW website
• Same charger location costs more through EnBW mobility+ than through the CPO's own app
• Price differs between two chargers at the same station
• Unexpected 'roaming fee' or 'session fee' on your invoice

How to Fix It

1. 1

   Check the price before you start the session

   In the EnBW mobility+ app, tap on the charger and look for the pricing details before starting. The app shows the per-kWh rate for that specific charger. Prices vary because each CPO sets different roaming rates.

2. 2

   Understand the pricing tiers

   EnBW mobility+ groups chargers into pricing tiers. 'EnBW own' chargers are cheapest, 'roaming standard' is mid-range, and 'roaming plus' (typically high-power chargers from premium CPOs like Ionity) costs more. The tier is usually shown in the charger details.

3. 3

   Compare with the CPO's own app

   If a charger is operated by Ionity, for example, check the Ionity app or website for their direct pricing. Sometimes the CPO's own app or RFID card is cheaper because there is no roaming middleman. If you use that CPO frequently, their own account may save you money.

4. 4

   Consider the EnBW mobility+ tariff you are on

   EnBW offers different tariffs (with and without a monthly fee). The tariff with a monthly fee usually gives lower per-kWh rates. In the app, go to your profile to check which tariff you are on and whether switching would save you money based on your usage.

5. 5

   Watch for idle fees and blocking fees

   Some chargers accessed through EnBW mobility+ charge a per-minute fee after your car finishes charging but the cable is still plugged in. Move your car promptly once charging is complete to avoid these fees.

App not loading charger details

You tap on a charger pin on the map and the detail screen is blank, shows a loading spinner forever, or displays outdated information. You cannot see pricing, availability, or the start button.

Symptoms

• Charger detail page shows a permanent loading spinner
• Availability status not updating (shows 'Available' for hours at a busy station)
• Price information missing from the detail screen
• App shows 'No connection' error when loading charger details

How to Fix It

1. 1

   Check your phone's internet connection

   Charging stations are often in areas with poor cellular coverage, like parking garages, highway rest stops behind concrete walls, or rural areas. Switch between mobile data and Wi-Fi, or walk to a spot with better signal and load the charger details there.

2. 2

   Force-close the app and reopen it

   Swipe the EnBW mobility+ app away from your recent apps list, wait a few seconds, and reopen it. Navigate to the charger again. This clears any stuck network requests.

3. 3

   Search for the charger by ID

   Instead of tapping the map pin, use the search bar in the app and enter the charger's ID or EVSE number (printed on the physical unit). This sometimes loads details that the map view fails to fetch.

4. 4

   Use the QR code on the charger as a backup

   Many chargers have a QR code that opens a direct session start page. Scan it with your phone camera. This page is served by the CPO, not EnBW, and often loads faster.

5. 5

   Clear the app cache

   On Android: Settings, Apps, EnBW mobility+, Storage, Clear Cache. On iOS: delete and reinstall the app (iOS does not offer cache clearing). This resolves issues caused by corrupted local data.

QR code scan not working

You scan the QR code on the charger with the EnBW mobility+ app and it either does not recognize the code, opens a wrong page, or shows an error.

Symptoms

• App says 'QR code not recognized' after scanning
• QR code opens a web page for the CPO's own app instead of EnBW mobility+
• Camera does not focus on the QR code (too dark, code damaged)
• Scan succeeds but the session start page shows an error

How to Fix It

1. 1

   Use the EnBW app's built-in scanner, not your phone camera

   Open the EnBW mobility+ app and use its QR scanner (usually in the top menu or via a scan button on the map screen). Scanning with your phone camera might open the CPO's own page instead of routing through EnBW.

2. 2

   Clean the QR code

   Wipe dirt, rain, or ice off the QR code with your sleeve. Damaged or faded QR codes are common on outdoor chargers. If the code is badly worn, look for a second QR code on a different part of the charger.

3. 3

   Turn on your phone's flashlight

   In dark or shaded areas, the camera cannot read the code. Most QR scanners (including EnBW's) have a flashlight toggle. Enable it for better readability.

4. 4

   Enter the charger ID manually

   If the QR code will not scan, look for the charger's numeric or alphanumeric ID printed nearby. Enter it manually in the EnBW app's search function to find and start the session.

Cannot stop the session from the app

You tap 'Stop Charging' in the EnBW mobility+ app and nothing happens. The session keeps running, your car keeps charging (or has already finished but the session stays active), and you want to unplug and leave.

Symptoms

• 'Stop' button in the app does not respond or shows an error
• Session shows as active in the app even after unplugging
• Charger screen says 'Session active' but your car is full
• You are worried about accumulating idle fees

How to Fix It

1. 1

   Physically unplug the connector from your car

   On most chargers, unplugging the cable ends the session automatically, regardless of what the app says. Unlock your car's charge port (from the car's screen, key fob, or charge port button) and remove the connector.

2. 2

   Wait 2 minutes and check the app again

   There is often a delay between physically ending the session and the app updating. The app depends on the CPO's system sending a 'session ended' signal back through the roaming chain. Give it a moment.

3. 3

   Force-close and reopen the app

   Sometimes the app's session view gets stuck. Force-close it, reopen, and check your session history. The session may already be ended on the backend even if the active session screen was not updating.

4. 4

   Press the stop button on the charger itself

   Many chargers have a physical stop button on the screen or housing. Press it. This sends the stop command directly to the charger hardware without going through the roaming network.

5. 5

   Contact support if you are being billed for a stuck session

   If the session stays 'active' in the app for more than 10 minutes after you have unplugged and driven away, contact EnBW mobility+ support. They can close the session on their end and correct any overcharges.

App is in German and hard to navigate

The EnBW mobility+ app defaults to German. If you do not speak German, navigating menus, understanding pricing details, and finding settings can be frustrating.

Symptoms

• All menus and buttons are in German after installation
• Language setting not obvious in the app
• Error messages appear in German, making troubleshooting difficult
• Pricing terms and tariff explanations are only in German

How to Fix It

1. 1

   Change your phone's system language temporarily

   The EnBW mobility+ app follows your phone's system language. If English is available in the app, switching your phone to English (Settings, General, Language) will switch the app too. You can switch back after you finish.

2. 2

   Check for an English option in the app settings

   Open the app, tap the profile or menu icon (usually three lines or a person icon in the corner), and look for 'Sprache' (Language) or 'Einstellungen' (Settings). Some versions offer English as an option directly.

3. 3

   Use your phone's translate feature on screenshots

   On iOS, take a screenshot and use Live Text to translate. On Android, use Google Lens. This is useful for understanding pricing details or error messages in German.

4. 4

   Consider an alternative roaming app with better language support

   If the language barrier is a persistent problem, apps like Shell Recharge, Plugsurfing, or Chargemap offer similar roaming coverage across Europe and have full English interfaces. They access many of the same chargers.