Volvo EX40 Charging at Atlante

Volvo EX40 Plugged In but the Charger Will Not Start

You plugged the cable into your Volvo EX40 and nothing happens. No charging animation on the center screen, no LED on the charger, or the charger shows an error. This is one of the most common frustrations at public chargers and is usually caused by authentication, the charge port, or the charger itself.

Symptoms

• Charger displays an error code or flashing red light after plugging in
• Charge port LED on the EX40 does not turn on or stays amber
• Google Built-In display shows no active charging session
• Charger screen says 'waiting for vehicle' or 'authentication failed'
• Cable is plugged in but the connector does not lock into the charge port

What to Do

1. 1

   Check if authentication is required

   Look at the charger's screen. Most public chargers need you to tap an RFID card, scan a QR code, or start the session through an app before charging begins. Plug & Charge works on some networks but not all.

2. 2

   Open the charge port fully

   Make sure the charge port door on the left rear of your EX40 is fully open. Press the edge of the door to release it if it is stuck. Clear any ice or debris in cold weather.

3. 3

   Push the connector in firmly

   Insert the CCS connector straight into the port and push until you hear a click. The connector should lock in place. If it will not lock, do not force it. Check for debris in the port.

4. 4

   Disable scheduled charging

   On the center display, go to Settings, then Charging. Check if a charging schedule is active. Turn it off or set it to 'charge immediately' to start charging at a public charger.

5. 5

   Unplug and try again

   Disconnect the cable, wait 10 seconds, and plug in again. Sometimes the communication handshake between car and charger fails on the first attempt and a retry resolves it.

6. 6

   Try a different charger or connector

   If the charger still will not start, move to a different stall or station. The charger may have an internal fault even if no error is displayed.

Volvo EX40 Charger Payment Failed or Card Declined

You are standing at a charger with your Volvo EX40, ready to charge, and the payment does not go through. Your card is declined, the app shows an error, or you cannot figure out how to pay at all. Payment problems at public chargers are one of the most common frustrations and usually have nothing to do with your car.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Charging app shows an error when trying to start a session
• No visible way to pay at the charger
• Contactless payment terminal does not respond to your card or phone
• Plug & Charge does not activate and the charger waits for payment

What to Do

1. 1

   Check if Plug & Charge is active

   Open the Volvo Cars app and check if Plug & Charge is enabled and linked to a payment method. If it is active, try unplugging and replugging the connector. Plug & Charge works only on supported networks.

2. 2

   Try a different payment method

   If your card was declined, try a different card, your phone's mobile wallet, or the charger network's app. Many chargers accept multiple payment options.

3. 3

   Check your card for pre-authorization holds

   Open your banking app and check for pending charges. If there are multiple holds from earlier charging attempts, your available balance may be too low. Call your bank to release them if needed.

4. 4

   Download the charger network's app

   Look at the charger for the network name or logo. Download their app, create an account, add a payment method, and start the session through the app instead of the charger's payment terminal.

5. 5

   Use an RFID charging card

   If you have an RFID card from a charging provider, tap it on the charger's reader. RFID cards work even when apps and contactless terminals fail. They are a reliable backup.

Volvo EX40 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX40 expecting 150 kW and the center screen shows 30 kW. Or your home wallbox is stuck at 3 kW instead of 11 kW. Slow charging on the EX40 is almost never a defect. It is usually the battery temperature, the charger itself, or a setting in the Volvo Cars app you can fix quickly.

Symptoms

• DC fast charging speed well below the 150 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 50-60%
• Google Built-In display shows lower power than the charger's rating
• Charging session starts at a reasonable speed but slows within minutes

What to Do

1. 1

   Check the battery temperature on the display

   Look at the charging screen on the EX40's center display (Google Built-In). If the battery is cold, drive for 15-20 minutes before charging or use the Volvo Cars app to start preconditioning before you arrive.

2. 2

   Use navigation to precondition the battery

   Set the charger as your destination in Google Maps on the center screen. The EX40 will automatically precondition the battery during the drive so it reaches optimal temperature for fast charging.

3. 3

   Check your state of charge

   If you are above 80%, the slower speed is normal. For fastest DC charging, arrive between 10-20% and charge to 80%. The last 20% takes as long as the first 80%.

4. 4

   Verify the charger is not sharing power

   Look at the charging unit. If there are two cables and someone is using the other one, you are likely sharing power. Move to a charger where both stalls are free.

5. 5

   Check the AC charge current setting

   In the EX40's settings menu, check that the charge current limiter is set to maximum. A reduced setting limits AC charging speed and is sometimes changed accidentally.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded. Try a different connector at the same station, or drive to another charging location.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.