Volvo EX40 Charging at ABC-lataus

Volvo EX40 Plugged In but the Charger Will Not Start

You plugged the cable into your Volvo EX40 and nothing happens. No charging animation on the center screen, no LED on the charger, or the charger shows an error. This is one of the most common frustrations at public chargers and is usually caused by authentication, the charge port, or the charger itself.

Symptoms

• Charger displays an error code or flashing red light after plugging in
• Charge port LED on the EX40 does not turn on or stays amber
• Google Built-In display shows no active charging session
• Charger screen says 'waiting for vehicle' or 'authentication failed'
• Cable is plugged in but the connector does not lock into the charge port

What to Do

1. 1

   Check if authentication is required

   Look at the charger's screen. Most public chargers need you to tap an RFID card, scan a QR code, or start the session through an app before charging begins. Plug & Charge works on some networks but not all.

2. 2

   Open the charge port fully

   Make sure the charge port door on the left rear of your EX40 is fully open. Press the edge of the door to release it if it is stuck. Clear any ice or debris in cold weather.

3. 3

   Push the connector in firmly

   Insert the CCS connector straight into the port and push until you hear a click. The connector should lock in place. If it will not lock, do not force it. Check for debris in the port.

4. 4

   Disable scheduled charging

   On the center display, go to Settings, then Charging. Check if a charging schedule is active. Turn it off or set it to 'charge immediately' to start charging at a public charger.

5. 5

   Unplug and try again

   Disconnect the cable, wait 10 seconds, and plug in again. Sometimes the communication handshake between car and charger fails on the first attempt and a retry resolves it.

6. 6

   Try a different charger or connector

   If the charger still will not start, move to a different stall or station. The charger may have an internal fault even if no error is displayed.

Volvo EX40 Charger Payment Failed or Card Declined

You are standing at a charger with your Volvo EX40, ready to charge, and the payment does not go through. Your card is declined, the app shows an error, or you cannot figure out how to pay at all. Payment problems at public chargers are one of the most common frustrations and usually have nothing to do with your car.

Symptoms

• Charger screen shows 'payment failed' or 'card declined'
• Charging app shows an error when trying to start a session
• No visible way to pay at the charger
• Contactless payment terminal does not respond to your card or phone
• Plug & Charge does not activate and the charger waits for payment

What to Do

1. 1

   Check if Plug & Charge is active

   Open the Volvo Cars app and check if Plug & Charge is enabled and linked to a payment method. If it is active, try unplugging and replugging the connector. Plug & Charge works only on supported networks.

2. 2

   Try a different payment method

   If your card was declined, try a different card, your phone's mobile wallet, or the charger network's app. Many chargers accept multiple payment options.

3. 3

   Check your card for pre-authorization holds

   Open your banking app and check for pending charges. If there are multiple holds from earlier charging attempts, your available balance may be too low. Call your bank to release them if needed.

4. 4

   Download the charger network's app

   Look at the charger for the network name or logo. Download their app, create an account, add a payment method, and start the session through the app instead of the charger's payment terminal.

5. 5

   Use an RFID charging card

   If you have an RFID card from a charging provider, tap it on the charger's reader. RFID cards work even when apps and contactless terminals fail. They are a reliable backup.

Volvo EX40 Charging Slower Than Expected at DC or AC

You plugged in your Volvo EX40 expecting 150 kW and the center screen shows 30 kW. Or your home wallbox is stuck at 3 kW instead of 11 kW. Slow charging on the EX40 is almost never a defect. It is usually the battery temperature, the charger itself, or a setting in the Volvo Cars app you can fix quickly.

Symptoms

• DC fast charging speed well below the 150 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops sharply after reaching 50-60%
• Google Built-In display shows lower power than the charger's rating
• Charging session starts at a reasonable speed but slows within minutes

What to Do

1. 1

   Check the battery temperature on the display

   Look at the charging screen on the EX40's center display (Google Built-In). If the battery is cold, drive for 15-20 minutes before charging or use the Volvo Cars app to start preconditioning before you arrive.

2. 2

   Use navigation to precondition the battery

   Set the charger as your destination in Google Maps on the center screen. The EX40 will automatically precondition the battery during the drive so it reaches optimal temperature for fast charging.

3. 3

   Check your state of charge

   If you are above 80%, the slower speed is normal. For fastest DC charging, arrive between 10-20% and charge to 80%. The last 20% takes as long as the first 80%.

4. 4

   Verify the charger is not sharing power

   Look at the charging unit. If there are two cables and someone is using the other one, you are likely sharing power. Move to a charger where both stalls are free.

5. 5

   Check the AC charge current setting

   In the EX40's settings menu, check that the charge current limiter is set to maximum. A reduced setting limits AC charging speed and is sometimes changed accidentally.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded. Try a different connector at the same station, or drive to another charging location.

Session fails to start or charger shows an error

You plug in and try to authenticate, but the charger does not begin charging. This can happen due to communication issues between your vehicle and the charger, or a problem with authentication.

Symptoms

• Charger shows an error after you try to start a session
• Contactless card payment does not work at this station (older unit without payment terminal)
• Card reader beeps but the session does not start
• The app says the session is starting but nothing happens at the charger

How to Fix It

1. 1

   Unplug, wait 30 seconds, and try again

   The initial communication handshake between your vehicle and the charger can fail. Unplug the connector, wait at least 30 seconds, and reconnect. The second attempt often works.

2. 2

   Try starting the session through the ABC-lataus app

   If the card reader is not cooperating, open the ABC-lataus app, select the station, and start the session from your phone. This bypasses the physical card reader entirely.

3. 3

   Try contactless card payment at newer stations

   Some newer ABC-lataus high-power stations have a contactless payment terminal. If the app is not cooperating, look for a card reader on the charger unit and tap your bank card. Older stations may not have this option.

4. 4

   Try a different charger unit at the same station

   If the station has multiple charger units, switch to another one. One unit may have a hardware issue while the others work fine.

Finding the EV charger at a busy fuel station

ABC-lataus chargers are located at ABC fuel stations, which also serve diesel and petrol vehicles. The EV charging spots can be easy to miss if you are visiting for the first time.

Symptoms

• You arrived at the ABC station but cannot see the EV charger
• The charger is behind the fuel pump area or in a separate parking section
• Other vehicles (non-EV) are parked in the charging spots
• Signage is not visible from the main road entrance

How to Fix It

1. 1

   Check the ABC-lataus app for the charger's exact location

   The app shows station details including photos or layout hints. Some ABC stations place chargers at the far end of the parking area, away from the fuel pumps.

2. 2

   Look for the CCS2 cable and charging unit

   The charger unit is taller than a fuel pump and usually has a clearly different design. Look for a separate bay with a CCS2 cable, often marked with green signage or an EV symbol on the ground.

3. 3

   Drive past the fuel pumps

   At many ABC stations, the EV charger is positioned after the fuel pump area or in a dedicated corner of the parking lot. Do not stop at the fuel pumps. Continue through and scan for the charging unit.

4. 4

   If an ICE vehicle is blocking the spot, report it

   ABC stations serve all types of vehicles. If a non-EV is parked in the charging bay, contact ABC customer service through the app. Unfortunately, there is not much you can do in the moment besides trying another station.

App setup confusion within the S-Group ecosystem

The ABC-lataus app is part of the S-Group digital ecosystem. If you already use S-mobiili for groceries or fuel, the relationship between the apps can be confusing.

Symptoms

• You are not sure whether to use S-mobiili or the ABC-lataus app
• Your S-Group login works in one app but not the other
• Charging payments do not appear in your S-mobiili transaction history
• You created a new account instead of linking your existing S-Group membership

How to Fix It

1. 1

   Use the ABC-lataus app for starting and managing charging sessions

   While S-mobiili handles your broader S-Group membership, the ABC-lataus app is the dedicated tool for finding stations, starting sessions, and viewing charging history. Install it separately from the App Store or Google Play.

2. 2

   Log in with your existing S-Group credentials

   Use the same username and password you use for S-mobiili or s-kanava.fi. Do not create a new account.

3. 3

   Check payment method settings in the ABC-lataus app

   Even if you have a payment card saved in S-mobiili, the ABC-lataus app may require you to add a payment method separately. Go to settings or payment in the ABC-lataus app and add your card there.

4. 4

   Verify your account is set up for charging

   Check the ABC-lataus app settings to make sure your payment method is saved and charging is enabled.

Connector stuck or difficult to insert in winter cold

Finnish winters mean temperatures well below freezing. The CCS2 connector locking mechanism and the vehicle's charge port can freeze, making it hard to plug in or unplug.

Symptoms

• The CCS2 connector will not click into your vehicle's charge port
• The connector is plugged in but the locking mechanism will not engage
• You cannot release the connector after charging is complete
• The connector handle feels stiff or the release button is frozen

How to Fix It

1. 1

   Check your vehicle's charge port for ice

   Open the charge port door and look for ice buildup around the opening or inside the port. Brush away any loose ice or snow with your hand or a soft brush. Do not use sharp tools, as you can damage the pins.

2. 2

   Warm the connector in your hands for a moment

   If the connector handle feels frozen stiff, hold it in your hands for 30 seconds to warm the mechanism slightly. The locking button and release lever work better when they are not frozen solid.

3. 3

   Push the connector in firmly and straight

   In cold weather, plastic contracts and tolerances get tighter. Line up the connector carefully and push it in with steady, even pressure. Do not force it at an angle.

4. 4

   If the connector is stuck after charging, try unlocking from your car

   Use your vehicle's unlock button or the in-car menu to release the charge port lock. Some vehicles also release the connector when you unlock the doors. If it is still stuck, wait a few minutes. The charging session generates heat that may free the mechanism.

5. 5

   Contact support if the connector will not release

   Do not yank the connector. Forcing it can damage both the cable and your vehicle's charge port. Call ABC-lataus support and they can guide you through a remote release or send help.

Charging session starts but power delivery is low

The charger is rated for 200 kW, but your session is delivering significantly less. Several factors specific to ABC-lataus stations can contribute.

Symptoms

• Dashboard shows 30 to 50 kW at a 200 kW rated charger
• Charging speed drops after a few minutes
• Speed is lower than what you get at other fast chargers
• The charger screen shows a lower maximum than 200 kW

How to Fix It

1. 1

   Check your vehicle's maximum DC charging rate

   A 200 kW charger does not mean your vehicle can accept 200 kW. Many EVs max out at 50 to 150 kW depending on the model, battery temperature, and state of charge. Check your vehicle's specifications.

2. 2

   Consider battery temperature in Finnish conditions

   Cold batteries accept less power. If your vehicle has been parked outside in freezing temperatures, the battery may need to warm up before it can accept higher charging speeds. Some vehicles have a preconditioning feature you can activate before arriving.

3. 3

   Check if another vehicle is sharing the station's power

   Some ABC-lataus locations share power between charger units. If another vehicle is charging at the same station, your available power may be split. This is normal and not a fault.

4. 4

   Arrive with a lower state of charge for faster charging

   Charging is fastest between 10% and 50% state of charge. If you arrive at 60% or higher, the charger will taper the power to protect your battery. This is your vehicle's doing, not the charger's.