Smart #1 Charging at Ionity

Smart #1 Pro Plus Charger Will Not Start a Session

You plugged the connector into your Smart #1, but the charger is not responding. No charging indicator, no session starting, nothing happening. This is almost always a charger-side or authentication issue, not a problem with the car. Let us work through it.

Symptoms

• The CCS2 or Type 2 connector is in but nothing happens
• The charger screen shows an error or stays on the welcome screen
• The Smart #1 dashboard does not show a charging session
• You hear the connector lock but charging does not begin
• The charging app shows the charger as available even though you are plugged in

What to Do

1. 1

   Authenticate with the charger first

   Tap your RFID card, open the charging network app, or use contactless payment on the charger. Wait for the charger screen to confirm the session before plugging in.

2. 2

   Remove and reinsert the connector

   Unlock the connector (press the button on the charger handle), remove it fully, wait 10 seconds, then push it back in firmly until it clicks and locks.

3. 3

   Lock and unlock the car

   Use the key fob or Smart app to lock the car, wait 15 seconds, then unlock it. This can reset the charging system if it is in a fault state.

4. 4

   Check the charge port for ice or debris

   Open the charge port flap on the rear left of the Smart #1 and inspect it. In winter, warm the port gently with your hands or use lukewarm water if ice is present. Never use hot water.

5. 5

   Restart the infotainment system

   Press and hold the power button on the center screen for 10 seconds to restart the system. Wait for it to boot fully, then try plugging in again.

6. 6

   Try a different charger

   If the session still will not start, the charger is likely faulty. Move to another charger at the station or a different location.

Smart #1 Pro Plus Payment Failed at Charging Station

You are ready to charge your Smart #1, but the payment will not go through. The RFID card does not register, the app gives an error, or your bank card gets declined. This is a charger and payment issue, not a car issue. Here is what to do.

Symptoms

• RFID card tap does nothing at the charger
• Charging app shows a payment or authorization error
• Contactless bank card is declined
• Charger displays a payment error code
• Session starts but stops immediately with a billing message

What to Do

1. 1

   Check which payment methods the charger accepts

   Look at the stickers and screen on the charger for accepted networks, apps, and card types. If your payment method is not listed, you need to try something else.

2. 2

   Switch to a different payment method

   Try a different RFID card, a different charging app, or a contactless bank card. Having multiple options is essential for public charging in Europe.

3. 3

   Check your available balance

   Open your banking app and verify you have at least 80 EUR available to cover the pre-authorization hold. If not, use a card with a higher balance.

4. 4

   Hold the RFID card steadily

   Place the RFID card flat against the reader and hold it for 2-3 seconds. Do not tap and remove quickly. Some readers are slow to respond.

5. 5

   Cancel and retry the session

   If a previous attempt is stuck, cancel it through the app first. Wait a minute, then start a fresh session from scratch.

6. 6

   Try the other charger unit

   If the payment hardware is faulty on one unit, the neighboring charger at the same station may work fine.

Smart #1 Pro Plus Charging Slower Than Expected Speed

Your Smart #1 should charge at up to 150 kW on DC and 22 kW on AC, but the numbers on the screen tell a different story. Maybe you are stuck at 40 kW on a fast charger, or your wallbox is only delivering 7 kW. Here is what is going on and how to fix it.

Symptoms

• DC fast charging well below the 150 kW maximum
• AC charging stuck at 7 or 11 kW instead of 22 kW
• Charging speed drops sharply after 50-60% state of charge
• The dashboard shows lower power than the charger rating
• Charging from 10% to 80% takes much longer than the advertised 30 minutes

What to Do

1. 1

   Use navigation to activate preconditioning

   Set the DC charger as your destination in the Smart #1's built-in navigation. This activates battery preconditioning, warming or cooling the battery to the ideal temperature before you arrive.

2. 2

   Check your state of charge

   If you are above 60%, the slower speed is expected. For the fastest DC charging, arrive between 10-20% and charge to 80%.

3. 3

   Verify the charger's actual output

   Check the charger display for its rated power. If it says 50 kW, that is your maximum regardless of the Smart #1's 150 kW capability. Look for chargers rated 150 kW or higher.

4. 4

   Check if the charger is shared

   If another car is using the adjacent connector on the same charger unit, you may be sharing power. Move to a charger with no other user if possible.

5. 5

   For AC, verify three-phase connection

   To get 22 kW AC, your wallbox must be wired for three-phase at 32A. Check with your electrician. If you only have single-phase, the maximum is about 7.4 kW.

6. 6

   Try a different charger

   If speeds are still low after checking everything, the charger may be degraded. Try another charger at the same station or a different location.

Session won't start after contactless payment

You tap your card, the reader beeps, but the charger never begins delivering power. This is one of the most reported issues at Ionity stations.

Symptoms

• Contactless reader shows a green light but nothing happens
• Screen says 'Initializing' for more than 60 seconds
• Card is charged a pre-authorization hold but no energy is delivered
• Error message appears after the tap but disappears too quickly to read

How to Fix It

1. 1

   Unplug the cable and wait 10 seconds

   This resets the charger's session state. Plug the cable back in firmly until you hear the locking click.

2. 2

   Try a different payment method

   Open the Ionity app and start the session from there instead. If you have an Ionity subscription, use the app. App-initiated sessions bypass the contactless reader entirely.

3. 3

   Check your card's contactless limit

   Some banks block contactless transactions above a certain amount. Ionity may pre-authorize up to 100 EUR. If your bank flags this, the session fails silently.

4. 4

   Move to another stall at the same station

   Individual charger units can have faulty card readers while the rest of the station works fine. Try the next available stall.

5. 5

   Check for a pending hold on your bank statement

   If a hold was placed but no session started, it typically releases within 3 to 7 business days. You will not be charged for energy you did not receive.

Plug & Charge pairing fails

Your vehicle supports Plug & Charge (ISO 15118) but the Ionity station does not recognize it. The charger asks for payment instead of starting automatically.

Symptoms

• Charger prompts for app or card payment instead of starting automatically
• Screen shows 'Vehicle not recognized'
• Plug & Charge worked at this station before but stopped working
• Pairing completed in the Ionity app but the station still asks for payment

How to Fix It

1. 1

   Verify Plug & Charge is enabled in your vehicle settings

   Some vehicles (like Porsche Taycan, BMW iX, Mercedes EQS) have a toggle in the infotainment system. If it was turned off during a software update, the charger cannot identify your car.

2. 2

   Re-pair your vehicle in the Ionity app

   Go to the Ionity app, navigate to Plug & Charge settings, remove the existing pairing, and set it up again. This refreshes the digital certificate.

3. 3

   Check that your Ionity subscription is active

   Plug & Charge on Ionity requires an active subscription. If your subscription lapsed, the auto-start will fail even if the pairing is intact.

4. 4

   Try unplugging and re-plugging slowly

   The ISO 15118 handshake happens in the first few seconds. If you plug in too quickly or the connector is not fully seated, the handshake times out and the charger falls back to manual payment.

5. 5

   Start the session via the app as a fallback

   Plug & Charge issues are often caused by backend certificate mismatches. You can still charge at Ionity subscription rates by starting the session through the app while the issue is resolved.

Charger screen frozen or unresponsive

The charger display is stuck on a loading screen, shows garbled text, or does not respond to touch. The hardware may still work even if the screen does not.

Symptoms

• Screen shows a logo or loading animation that never progresses
• Touch inputs on the screen do nothing
• Screen is completely black but the charger lights are on
• Screen shows an error code that does not clear

How to Fix It

1. 1

   Try plugging in and starting via the app

   The screen and the charging hardware are separate systems. Many Ionity chargers will still deliver power even with a frozen display if you initiate the session through the Ionity app.

2. 2

   Unplug completely and wait 30 seconds

   Sometimes unplugging triggers a soft reset of the charger unit. Wait, then try again.

3. 3

   Try a different stall

   Ionity stations typically have multiple charger units. A frozen screen on one unit does not affect the others.

4. 4

   Report the charger in the Ionity app

   Open the Ionity app, find the station, and report the specific charger as out of order. This helps Ionity dispatch maintenance faster.

App shows station available but charger is faulted

The Ionity app shows green (available) status for a station, but when you arrive, the chargers display errors or are physically out of service.

Symptoms

• App shows 'Available' but charger displays 'Out of Order'
• All stalls at the station are faulted despite the app showing availability
• Charger has a maintenance sticker or barrier but the app has not been updated
• You drove to a station specifically because the app said it was free

How to Fix It

1. 1

   Refresh the station status in the app

   Pull down to refresh the station view. Status updates can lag by several minutes, especially after a charger was recently reported or rebooted.

2. 2

   Check individual charger status, not just the station

   Tap into the station details in the Ionity app. Even if some stalls show faulted, others at the same station may still work.

3. 3

   Try plugging in anyway

   Occasionally a charger shows a stale error on its screen from a previous session but works fine for the next user. Plug in and attempt to start via the app.

4. 4

   Plan a backup station

   Before driving to an Ionity station, check if there is an alternative station within 10 to 15 minutes. Ionity stations along highways sometimes have another Ionity or competitor station at the next exit.

5. 5

   Report the discrepancy

   Use the 'Report a problem' option in the Ionity app. Accurate reports help Ionity fix status sync issues and prioritize maintenance.

Unexpectedly high ad-hoc price

You charged without an Ionity subscription subscription and the per-kWh price is significantly higher than you expected. Ionity's ad-hoc rate is one of the most expensive in Europe.

Symptoms

• Invoice shows 0.75 EUR/kWh or higher
• Total cost for a short session is much higher than expected
• Price displayed on the charger screen was not noticed before starting
• You assumed the price would be similar to home charging or other networks

How to Fix It

1. 1

   Check if Ionity subscription would save you money

   Ionity offers subscription plans that reduce the per-kWh price significantly. Check the Ionity app for current plans and rates. If you charge at Ionity more than once or twice a month, a subscription usually pays for itself.

2. 2

   Check your vehicle manufacturer's charging plan

   Many EV manufacturers (Hyundai, Kia, BMW, Mercedes, Volkswagen Group, Ford) offer bundled Ionity pricing through their own apps. You may already have access to a discounted rate through your car brand.

3. 3

   Look at the charger screen before starting next time

   Ionity displays the per-kWh price on the charger screen before the session starts. The ad-hoc price is always shown.

4. 4

   Consider roaming providers for occasional use

   If you do not want a subscription, some roaming apps (like Shell Recharge, Chargemap, or Maingau) offer lower Ionity rates than the ad-hoc price.

Charging speed much lower than 350 kW

The station advertises 350 kW but your vehicle is charging at a fraction of that speed. This can be normal or it can indicate a problem.

Symptoms

• Dashboard shows 50 to 100 kW at a 350 kW charger
• Charging started fast but dropped sharply after a few minutes
• Other vehicles at the same station seem to charge faster
• Speed is lower than what you normally get at Ionity

How to Fix It

1. 1

   Check your battery level

   Charging speed drops significantly above 60 to 80% state of charge on most vehicles. This is normal battery behavior, not an Ionity issue. For the fastest stop, charge from 10 to 80% and move on.

2. 2

   Check the battery temperature

   Cold batteries charge slowly. If your vehicle supports battery preconditioning, set the Ionity station as your navigation destination. The car will warm the battery on the way there.

3. 3

   Verify your vehicle's max DC charging speed

   Not all EVs can accept 350 kW. Many popular models top out at 100 to 150 kW. The charger delivers only what the vehicle requests.

4. 4

   Try a different stall

   Individual charger units can occasionally have hardware limitations or faults that reduce output. Moving to another stall at the same station can sometimes restore full speed.

5. 5

   Check for power sharing

   Some Ionity stations share power between adjacent stalls. If the neighboring stall is also in use, both vehicles may receive reduced power. Try a stall that is not next to another active session.