Smart #1 Charging at EnBW mobility+

Smart #1 Pro Plus Charger Will Not Start a Session

You plugged the connector into your Smart #1, but the charger is not responding. No charging indicator, no session starting, nothing happening. This is almost always a charger-side or authentication issue, not a problem with the car. Let us work through it.

Symptoms

• The CCS2 or Type 2 connector is in but nothing happens
• The charger screen shows an error or stays on the welcome screen
• The Smart #1 dashboard does not show a charging session
• You hear the connector lock but charging does not begin
• The charging app shows the charger as available even though you are plugged in

What to Do

1. 1

   Authenticate with the charger first

   Tap your RFID card, open the charging network app, or use contactless payment on the charger. Wait for the charger screen to confirm the session before plugging in.

2. 2

   Remove and reinsert the connector

   Unlock the connector (press the button on the charger handle), remove it fully, wait 10 seconds, then push it back in firmly until it clicks and locks.

3. 3

   Lock and unlock the car

   Use the key fob or Smart app to lock the car, wait 15 seconds, then unlock it. This can reset the charging system if it is in a fault state.

4. 4

   Check the charge port for ice or debris

   Open the charge port flap on the rear left of the Smart #1 and inspect it. In winter, warm the port gently with your hands or use lukewarm water if ice is present. Never use hot water.

5. 5

   Restart the infotainment system

   Press and hold the power button on the center screen for 10 seconds to restart the system. Wait for it to boot fully, then try plugging in again.

6. 6

   Try a different charger

   If the session still will not start, the charger is likely faulty. Move to another charger at the station or a different location.

Smart #1 Pro Plus Payment Failed at Charging Station

You are ready to charge your Smart #1, but the payment will not go through. The RFID card does not register, the app gives an error, or your bank card gets declined. This is a charger and payment issue, not a car issue. Here is what to do.

Symptoms

• RFID card tap does nothing at the charger
• Charging app shows a payment or authorization error
• Contactless bank card is declined
• Charger displays a payment error code
• Session starts but stops immediately with a billing message

What to Do

1. 1

   Check which payment methods the charger accepts

   Look at the stickers and screen on the charger for accepted networks, apps, and card types. If your payment method is not listed, you need to try something else.

2. 2

   Switch to a different payment method

   Try a different RFID card, a different charging app, or a contactless bank card. Having multiple options is essential for public charging in Europe.

3. 3

   Check your available balance

   Open your banking app and verify you have at least 80 EUR available to cover the pre-authorization hold. If not, use a card with a higher balance.

4. 4

   Hold the RFID card steadily

   Place the RFID card flat against the reader and hold it for 2-3 seconds. Do not tap and remove quickly. Some readers are slow to respond.

5. 5

   Cancel and retry the session

   If a previous attempt is stuck, cancel it through the app first. Wait a minute, then start a fresh session from scratch.

6. 6

   Try the other charger unit

   If the payment hardware is faulty on one unit, the neighboring charger at the same station may work fine.

Smart #1 Pro Plus Charging Slower Than Expected Speed

Your Smart #1 should charge at up to 150 kW on DC and 22 kW on AC, but the numbers on the screen tell a different story. Maybe you are stuck at 40 kW on a fast charger, or your wallbox is only delivering 7 kW. Here is what is going on and how to fix it.

Symptoms

• DC fast charging well below the 150 kW maximum
• AC charging stuck at 7 or 11 kW instead of 22 kW
• Charging speed drops sharply after 50-60% state of charge
• The dashboard shows lower power than the charger rating
• Charging from 10% to 80% takes much longer than the advertised 30 minutes

What to Do

1. 1

   Use navigation to activate preconditioning

   Set the DC charger as your destination in the Smart #1's built-in navigation. This activates battery preconditioning, warming or cooling the battery to the ideal temperature before you arrive.

2. 2

   Check your state of charge

   If you are above 60%, the slower speed is expected. For the fastest DC charging, arrive between 10-20% and charge to 80%.

3. 3

   Verify the charger's actual output

   Check the charger display for its rated power. If it says 50 kW, that is your maximum regardless of the Smart #1's 150 kW capability. Look for chargers rated 150 kW or higher.

4. 4

   Check if the charger is shared

   If another car is using the adjacent connector on the same charger unit, you may be sharing power. Move to a charger with no other user if possible.

5. 5

   For AC, verify three-phase connection

   To get 22 kW AC, your wallbox must be wired for three-phase at 32A. Check with your electrician. If you only have single-phase, the maximum is about 7.4 kW.

6. 6

   Try a different charger

   If speeds are still low after checking everything, the charger may be degraded. Try another charger at the same station or a different location.

Roaming pricing unclear or higher than expected

You started a session through EnBW mobility+ and the per-kWh price was significantly higher than you expected. The same charger costs different amounts at different times, and the pricing logic feels opaque.

Symptoms

• Per-kWh rate on the receipt is higher than the rate shown on the EnBW website
• Same charger location costs more through EnBW mobility+ than through the CPO's own app
• Price differs between two chargers at the same station
• Unexpected 'roaming fee' or 'session fee' on your invoice

How to Fix It

1. 1

   Check the price before you start the session

   In the EnBW mobility+ app, tap on the charger and look for the pricing details before starting. The app shows the per-kWh rate for that specific charger. Prices vary because each CPO sets different roaming rates.

2. 2

   Understand the pricing tiers

   EnBW mobility+ groups chargers into pricing tiers. 'EnBW own' chargers are cheapest, 'roaming standard' is mid-range, and 'roaming plus' (typically high-power chargers from premium CPOs like Ionity) costs more. The tier is usually shown in the charger details.

3. 3

   Compare with the CPO's own app

   If a charger is operated by Ionity, for example, check the Ionity app or website for their direct pricing. Sometimes the CPO's own app or RFID card is cheaper because there is no roaming middleman. If you use that CPO frequently, their own account may save you money.

4. 4

   Consider the EnBW mobility+ tariff you are on

   EnBW offers different tariffs (with and without a monthly fee). The tariff with a monthly fee usually gives lower per-kWh rates. In the app, go to your profile to check which tariff you are on and whether switching would save you money based on your usage.

5. 5

   Watch for idle fees and blocking fees

   Some chargers accessed through EnBW mobility+ charge a per-minute fee after your car finishes charging but the cable is still plugged in. Move your car promptly once charging is complete to avoid these fees.

App not loading charger details

You tap on a charger pin on the map and the detail screen is blank, shows a loading spinner forever, or displays outdated information. You cannot see pricing, availability, or the start button.

Symptoms

• Charger detail page shows a permanent loading spinner
• Availability status not updating (shows 'Available' for hours at a busy station)
• Price information missing from the detail screen
• App shows 'No connection' error when loading charger details

How to Fix It

1. 1

   Check your phone's internet connection

   Charging stations are often in areas with poor cellular coverage, like parking garages, highway rest stops behind concrete walls, or rural areas. Switch between mobile data and Wi-Fi, or walk to a spot with better signal and load the charger details there.

2. 2

   Force-close the app and reopen it

   Swipe the EnBW mobility+ app away from your recent apps list, wait a few seconds, and reopen it. Navigate to the charger again. This clears any stuck network requests.

3. 3

   Search for the charger by ID

   Instead of tapping the map pin, use the search bar in the app and enter the charger's ID or EVSE number (printed on the physical unit). This sometimes loads details that the map view fails to fetch.

4. 4

   Use the QR code on the charger as a backup

   Many chargers have a QR code that opens a direct session start page. Scan it with your phone camera. This page is served by the CPO, not EnBW, and often loads faster.

5. 5

   Clear the app cache

   On Android: Settings, Apps, EnBW mobility+, Storage, Clear Cache. On iOS: delete and reinstall the app (iOS does not offer cache clearing). This resolves issues caused by corrupted local data.

QR code scan not working

You scan the QR code on the charger with the EnBW mobility+ app and it either does not recognize the code, opens a wrong page, or shows an error.

Symptoms

• App says 'QR code not recognized' after scanning
• QR code opens a web page for the CPO's own app instead of EnBW mobility+
• Camera does not focus on the QR code (too dark, code damaged)
• Scan succeeds but the session start page shows an error

How to Fix It

1. 1

   Use the EnBW app's built-in scanner, not your phone camera

   Open the EnBW mobility+ app and use its QR scanner (usually in the top menu or via a scan button on the map screen). Scanning with your phone camera might open the CPO's own page instead of routing through EnBW.

2. 2

   Clean the QR code

   Wipe dirt, rain, or ice off the QR code with your sleeve. Damaged or faded QR codes are common on outdoor chargers. If the code is badly worn, look for a second QR code on a different part of the charger.

3. 3

   Turn on your phone's flashlight

   In dark or shaded areas, the camera cannot read the code. Most QR scanners (including EnBW's) have a flashlight toggle. Enable it for better readability.

4. 4

   Enter the charger ID manually

   If the QR code will not scan, look for the charger's numeric or alphanumeric ID printed nearby. Enter it manually in the EnBW app's search function to find and start the session.

Cannot stop the session from the app

You tap 'Stop Charging' in the EnBW mobility+ app and nothing happens. The session keeps running, your car keeps charging (or has already finished but the session stays active), and you want to unplug and leave.

Symptoms

• 'Stop' button in the app does not respond or shows an error
• Session shows as active in the app even after unplugging
• Charger screen says 'Session active' but your car is full
• You are worried about accumulating idle fees

How to Fix It

1. 1

   Physically unplug the connector from your car

   On most chargers, unplugging the cable ends the session automatically, regardless of what the app says. Unlock your car's charge port (from the car's screen, key fob, or charge port button) and remove the connector.

2. 2

   Wait 2 minutes and check the app again

   There is often a delay between physically ending the session and the app updating. The app depends on the CPO's system sending a 'session ended' signal back through the roaming chain. Give it a moment.

3. 3

   Force-close and reopen the app

   Sometimes the app's session view gets stuck. Force-close it, reopen, and check your session history. The session may already be ended on the backend even if the active session screen was not updating.

4. 4

   Press the stop button on the charger itself

   Many chargers have a physical stop button on the screen or housing. Press it. This sends the stop command directly to the charger hardware without going through the roaming network.

5. 5

   Contact support if you are being billed for a stuck session

   If the session stays 'active' in the app for more than 10 minutes after you have unplugged and driven away, contact EnBW mobility+ support. They can close the session on their end and correct any overcharges.

App is in German and hard to navigate

The EnBW mobility+ app defaults to German. If you do not speak German, navigating menus, understanding pricing details, and finding settings can be frustrating.

Symptoms

• All menus and buttons are in German after installation
• Language setting not obvious in the app
• Error messages appear in German, making troubleshooting difficult
• Pricing terms and tariff explanations are only in German

How to Fix It

1. 1

   Change your phone's system language temporarily

   The EnBW mobility+ app follows your phone's system language. If English is available in the app, switching your phone to English (Settings, General, Language) will switch the app too. You can switch back after you finish.

2. 2

   Check for an English option in the app settings

   Open the app, tap the profile or menu icon (usually three lines or a person icon in the corner), and look for 'Sprache' (Language) or 'Einstellungen' (Settings). Some versions offer English as an option directly.

3. 3

   Use your phone's translate feature on screenshots

   On iOS, take a screenshot and use Live Text to translate. On Android, use Google Lens. This is useful for understanding pricing details or error messages in German.

4. 4

   Consider an alternative roaming app with better language support

   If the language barrier is a persistent problem, apps like Shell Recharge, Plugsurfing, or Chargemap offer similar roaming coverage across Europe and have full English interfaces. They access many of the same chargers.