Smart #1 Charging at GreenWay

Smart #1 Pro Plus Charger Will Not Start a Session

You plugged the connector into your Smart #1, but the charger is not responding. No charging indicator, no session starting, nothing happening. This is almost always a charger-side or authentication issue, not a problem with the car. Let us work through it.

Symptoms

• The CCS2 or Type 2 connector is in but nothing happens
• The charger screen shows an error or stays on the welcome screen
• The Smart #1 dashboard does not show a charging session
• You hear the connector lock but charging does not begin
• The charging app shows the charger as available even though you are plugged in

What to Do

1. 1

   Authenticate with the charger first

   Tap your RFID card, open the charging network app, or use contactless payment on the charger. Wait for the charger screen to confirm the session before plugging in.

2. 2

   Remove and reinsert the connector

   Unlock the connector (press the button on the charger handle), remove it fully, wait 10 seconds, then push it back in firmly until it clicks and locks.

3. 3

   Lock and unlock the car

   Use the key fob or Smart app to lock the car, wait 15 seconds, then unlock it. This can reset the charging system if it is in a fault state.

4. 4

   Check the charge port for ice or debris

   Open the charge port flap on the rear left of the Smart #1 and inspect it. In winter, warm the port gently with your hands or use lukewarm water if ice is present. Never use hot water.

5. 5

   Restart the infotainment system

   Press and hold the power button on the center screen for 10 seconds to restart the system. Wait for it to boot fully, then try plugging in again.

6. 6

   Try a different charger

   If the session still will not start, the charger is likely faulty. Move to another charger at the station or a different location.

Smart #1 Pro Plus Payment Failed at Charging Station

You are ready to charge your Smart #1, but the payment will not go through. The RFID card does not register, the app gives an error, or your bank card gets declined. This is a charger and payment issue, not a car issue. Here is what to do.

Symptoms

• RFID card tap does nothing at the charger
• Charging app shows a payment or authorization error
• Contactless bank card is declined
• Charger displays a payment error code
• Session starts but stops immediately with a billing message

What to Do

1. 1

   Check which payment methods the charger accepts

   Look at the stickers and screen on the charger for accepted networks, apps, and card types. If your payment method is not listed, you need to try something else.

2. 2

   Switch to a different payment method

   Try a different RFID card, a different charging app, or a contactless bank card. Having multiple options is essential for public charging in Europe.

3. 3

   Check your available balance

   Open your banking app and verify you have at least 80 EUR available to cover the pre-authorization hold. If not, use a card with a higher balance.

4. 4

   Hold the RFID card steadily

   Place the RFID card flat against the reader and hold it for 2-3 seconds. Do not tap and remove quickly. Some readers are slow to respond.

5. 5

   Cancel and retry the session

   If a previous attempt is stuck, cancel it through the app first. Wait a minute, then start a fresh session from scratch.

6. 6

   Try the other charger unit

   If the payment hardware is faulty on one unit, the neighboring charger at the same station may work fine.

Smart #1 Pro Plus Charging Slower Than Expected Speed

Your Smart #1 should charge at up to 150 kW on DC and 22 kW on AC, but the numbers on the screen tell a different story. Maybe you are stuck at 40 kW on a fast charger, or your wallbox is only delivering 7 kW. Here is what is going on and how to fix it.

Symptoms

• DC fast charging well below the 150 kW maximum
• AC charging stuck at 7 or 11 kW instead of 22 kW
• Charging speed drops sharply after 50-60% state of charge
• The dashboard shows lower power than the charger rating
• Charging from 10% to 80% takes much longer than the advertised 30 minutes

What to Do

1. 1

   Use navigation to activate preconditioning

   Set the DC charger as your destination in the Smart #1's built-in navigation. This activates battery preconditioning, warming or cooling the battery to the ideal temperature before you arrive.

2. 2

   Check your state of charge

   If you are above 60%, the slower speed is expected. For the fastest DC charging, arrive between 10-20% and charge to 80%.

3. 3

   Verify the charger's actual output

   Check the charger display for its rated power. If it says 50 kW, that is your maximum regardless of the Smart #1's 150 kW capability. Look for chargers rated 150 kW or higher.

4. 4

   Check if the charger is shared

   If another car is using the adjacent connector on the same charger unit, you may be sharing power. Move to a charger with no other user if possible.

5. 5

   For AC, verify three-phase connection

   To get 22 kW AC, your wallbox must be wired for three-phase at 32A. Check with your electrician. If you only have single-phase, the maximum is about 7.4 kW.

6. 6

   Try a different charger

   If speeds are still low after checking everything, the charger may be degraded. Try another charger at the same station or a different location.

App-only payment with no backup option

GreenWay stations require the GreenWay app to start a session. There are no contactless card readers or RFID pads. If the app fails or your phone dies, you cannot charge.

Symptoms

• No card reader or RFID pad visible on the charger
• Charger screen shows a QR code or 'Use app to start' message
• You arrived without the app installed and cannot begin a session
• Your phone battery is low and you are worried it will die during setup

How to Fix It

1. 1

   Download the GreenWay app before your trip

   This is non-negotiable for GreenWay stations. Install the app, create an account, and add a payment method while you have good internet and battery. Do this before you leave, not at the charger.

2. 2

   Charge your phone before arriving at the station

   Since you need your phone to start and monitor the session, make sure it has enough battery. Use your car's USB port or a power bank on the way.

3. 3

   Try a roaming app as a backup

   Some GreenWay stations are accessible through roaming providers like Plugsurfing, Shell Recharge, or Chargemap. Check your roaming app's map to see if the specific station is covered before counting on it.

4. 4

   Scan the QR code on the charger

   If you do not have the app, scan the QR code with your phone camera. It may direct you to the app store or, in some cases, to a web-based session start page.

App requires location services for charger activation

The GreenWay app needs location services turned on to activate a charger. Without it, the app cannot verify that you are at the station and will not let you start a session.

Symptoms

• App shows 'Enable location services' and will not proceed
• You can see the charger on the map but cannot start a session
• The 'Start charging' button is grayed out or unresponsive
• App shows your location incorrectly, placing you far from the station

How to Fix It

1. 1

   Enable location services for the GreenWay app

   Go to your phone settings, find the GreenWay app, and set location access to 'While Using' or 'Always.' On iPhone: Settings, Privacy, Location Services, GreenWay. On Android: Settings, Apps, GreenWay, Permissions, Location.

2. 2

   Make sure GPS is turned on, not just Wi-Fi location

   In some areas, Wi-Fi-based location is inaccurate. Turn on full GPS (high accuracy mode on Android) for a precise position fix at the station.

3. 3

   Step outside your vehicle briefly

   If GPS signal is weak (underground parking, dense urban area), step a few meters away from your car with your phone. This can help the GPS lock onto your position.

4. 4

   Try selecting the charger manually

   If the app cannot determine your location, try tapping on the station on the map manually or entering the charger's ID number (printed on the charger unit). Some app versions allow manual selection as a fallback.

Coverage gaps between cities

GreenWay's network is concentrated in and around cities. Between major cities, especially on secondary roads, there can be long stretches with no GreenWay stations.

Symptoms

• No GreenWay stations shown on the app map for 100+ km stretches
• The nearest GreenWay station requires a detour off your route
• You planned a trip assuming GreenWay coverage and ran into a gap
• Available stations between cities are AC-only (slow), not DC fast charging

How to Fix It

1. 1

   Plan your route and charging stops before leaving

   Use the GreenWay app or a route planner like ABRP (A Better Route Planner) to map out charging stops. Identify gaps in advance so you are not caught by surprise.

2. 2

   Have alternative charging networks ready

   Install apps for other networks that operate in the region. In Slovakia and Poland, look for Ionity, Shell Recharge, or Greencharge. In Czech Republic, check CEZ or PRE. Having multiple apps ensures you always have a fallback.

3. 3

   Charge to a higher level before entering a gap

   If you know there is a 150+ km stretch without fast chargers, charge to 90 or even 95% at the last available station. The slower charging speed above 80% is worth it if the alternative is running out of range.

4. 4

   Check for AC chargers as emergency backup

   Hotels, shopping centers, and some gas stations in Central Europe have AC chargers (Type 2, 11 to 22 kW). These are slow but can add enough range to reach the next fast charger. Many are accessible through Chargemap or Plugsurfing.

Charger screen errors in local language only

When a GreenWay charger displays an error, the message is often in Slovak, Polish, or Czech with no English translation. Understanding what went wrong is difficult.

Symptoms

• Error message appears in Slovak, Polish, or Czech
• You cannot tell if the error is temporary or requires support
• The charger stopped and you do not know why
• The error code is visible but the description is in a language you do not read

How to Fix It

1. 1

   Note the error code, not just the text

   Most error messages include a numeric or alphanumeric code (like E-101 or ERR_04). Write down or photograph the code. This is useful for support and often means the same thing regardless of language.

2. 2

   Use your phone camera to translate the screen

   Open Google Translate or Apple Translate, switch to camera mode, and point it at the charger screen. This gives a real-time translation of the error message.

3. 3

   Try unplugging and restarting the session

   Many error messages clear on a retry. Unplug, wait 15 seconds, plug back in, and start a new session through the app. Common errors like 'Communication timeout' resolve themselves.

4. 4

   Contact GreenWay support with the error code

   If the error persists, contact support through the GreenWay app. Provide the error code and the station ID (printed on the charger). GreenWay support can tell you whether the issue is temporary or requires a technician.

Power limited at older installations

Some older GreenWay stations deliver less than 150 kW. They may be rated at 50 kW or have degraded power output due to aging hardware.

Symptoms

• Charging speed maxes out at 50 kW on a station advertised as 150 kW
• The charger label says 150 kW but your vehicle never receives more than 50 kW
• Speed is significantly lower than what you get at newer GreenWay stations
• The app shows the station as 150 kW but the charger hardware looks older

How to Fix It

1. 1

   Check the charger label for the actual rated power

   The charger unit itself has a label showing its maximum output. Older GreenWay units may be rated at 50 kW despite the station listing showing 150 kW (which may refer to a newer unit at the same location).

2. 2

   Check if the station has multiple charger types

   Some GreenWay stations have both older 50 kW and newer 150 kW chargers. Make sure you are plugged into the newer, higher-power unit. It is usually the larger cabinet.

3. 3

   Verify your vehicle's battery level and temperature

   Your vehicle limits charging speed when the battery is above 60 to 80% or when the battery is cold. Check your dashboard to confirm the car is requesting more than what the charger delivers.

4. 4

   Use a different station if speed matters

   If you need faster charging and the station is limited, check the GreenWay app for a newer station nearby. Filter by power level to find 150 kW units specifically.