MG MG5 Charging at ABC-lataus

MG MG5 Charger Won't Start? Step-by-Step Help

You have plugged in your MG MG5 and the charging session refuses to start. The charger might be blinking, showing an error, or doing nothing at all. This is a common problem across all EVs, and the MG5 is no exception. Most causes are easy to diagnose and fix on the spot.

Symptoms

• Charger display shows an error or stays on the start screen
• CCS2 connector plugs in but charging does not initiate
• MG5 charge port light does not turn on or stays amber
• App shows the charger as available but the session does not begin
• AC Type 2 cable locks in but no power flows

What to Do

1. 1

   Read the charger screen

   Check for error messages, authentication prompts, or status indicators. If it says 'waiting for vehicle' the problem is on the car side. If it says 'error' or 'out of service,' the charger is the issue.

2. 2

   Unplug, wait, and replug

   Remove the connector completely, wait 15 seconds, and reinsert it firmly. Listen for the locking click on the MG5's charge port. This resets the communication handshake.

3. 3

   Complete authentication

   Tap your RFID card, open the network app and start the session, or use contactless payment. Some chargers need you to authenticate before plugging in, others after.

4. 4

   Check for scheduled charging

   Go to the MG5's charging settings on the infotainment screen. If a charging schedule is active, disable it to allow immediate charging.

5. 5

   Restart the car's systems

   Turn the MG5 off using the start button, wait 30 seconds, then turn it back on. This can clear temporary software glitches that prevent the charge port from communicating.

6. 6

   Move to another stall or station

   If the charger is at fault, try another stall. If no stalls work, the station may have a site-wide issue. Find an alternative station using your charging app.

MG MG5 Charging Payment Failed? How to Fix It

You are standing at a charger with your MG MG5 and the payment will not work. Card declined, app throwing errors, or no idea how to pay at all. This is one of the most frustrating parts of public charging, and it happens to everyone. Here is how to get past it.

Symptoms

• RFID card not recognized when tapped on the charger
• Charging app shows payment error or transaction declined
• Contactless card payment rejected at the terminal
• Charger starts authentication but then returns an error
• Session begins but ends immediately due to payment failure

What to Do

1. 1

   Identify accepted payment methods

   Look at the charger for payment logos and instructions. Note whether it accepts RFID cards, specific apps, contactless cards, or QR code payments. Each charger may support different methods.

2. 2

   Try the network's own app

   Download the charger network's app, create an account, and add a payment method. Then start the session through the app. This bypasses RFID and contactless issues.

3. 3

   Switch to an alternative payment method

   If your primary RFID card fails, try contactless with your bank card. If that fails, try a roaming provider like Plugsurfing, Shell Recharge, or Chargemap.

4. 4

   Check your bank for blocked transactions

   Open your banking app and look for declined or pending transactions. If the pre-authorization was blocked, call your bank or temporarily increase your card limit.

5. 5

   Try a different stall

   If the card reader on one stall is broken, another stall at the same station may have a working reader. Try the next one before giving up on the location.

6. 6

   Find an alternative station

   Use your charging app to find a nearby station from a network where your payment methods are confirmed to work. Filter by your preferred payment method if the app supports it.

MG MG5 Charging Slowly? Why and How to Fix It

Your MG MG5 is charging slower than you expected. With a maximum DC speed of 87kW, the MG5 is not the fastest charger in its class, but it should still deliver reasonable speeds. If you are seeing numbers well below that, something else is going on. Here is what to check.

Symptoms

• DC charging power showing well below 87kW on the charger display
• AC charging stuck below 11kW on a capable wallbox
• Estimated charging time significantly longer than expected
• Charging speed drops sharply above 50-60% SOC
• Very slow charging in cold weather conditions

What to Do

1. 1

   Check the charger's maximum power output

   Verify the charger is rated above 87kW. If it is a 50kW charger, the MG5 is getting the maximum available. Look at the charger label or check in the network app.

2. 2

   Use preconditioning in cold weather

   Set the fast charger as your destination in the MG5's navigation system. This activates battery preconditioning, which warms the battery before you arrive and improves initial charging speed.

3. 3

   Check your state of charge

   If you are above 60% SOC, the MG5's charging taper is expected. For the fastest session, arrive at the charger between 10-20% SOC and charge to 70-80%.

4. 4

   Try a different stall to avoid power sharing

   If the station shares power between stalls, wait for other cars to finish or move to a stall that is not paired with another active charger. Some stations label which stalls share power.

5. 5

   For AC, verify your cable and charger

   Make sure you are using a 3-phase Type 2 cable on an 11kW or higher AC charger. A single-phase connection limits you to about 3.6kW, which adds many hours to a full charge.

6. 6

   Check car settings for charging limits

   In the MG5's settings, look for any AC current limit or maximum charge level that might be capping your speed.

Session fails to start or charger shows an error

You plug in and try to authenticate, but the charger does not begin charging. This can happen due to communication issues between your vehicle and the charger, or a problem with authentication.

Symptoms

• Charger shows an error after you try to start a session
• Contactless card payment does not work at this station (older unit without payment terminal)
• Card reader beeps but the session does not start
• The app says the session is starting but nothing happens at the charger

How to Fix It

1. 1

   Unplug, wait 30 seconds, and try again

   The initial communication handshake between your vehicle and the charger can fail. Unplug the connector, wait at least 30 seconds, and reconnect. The second attempt often works.

2. 2

   Try starting the session through the ABC-lataus app

   If the card reader is not cooperating, open the ABC-lataus app, select the station, and start the session from your phone. This bypasses the physical card reader entirely.

3. 3

   Try contactless card payment at newer stations

   Some newer ABC-lataus high-power stations have a contactless payment terminal. If the app is not cooperating, look for a card reader on the charger unit and tap your bank card. Older stations may not have this option.

4. 4

   Try a different charger unit at the same station

   If the station has multiple charger units, switch to another one. One unit may have a hardware issue while the others work fine.

Finding the EV charger at a busy fuel station

ABC-lataus chargers are located at ABC fuel stations, which also serve diesel and petrol vehicles. The EV charging spots can be easy to miss if you are visiting for the first time.

Symptoms

• You arrived at the ABC station but cannot see the EV charger
• The charger is behind the fuel pump area or in a separate parking section
• Other vehicles (non-EV) are parked in the charging spots
• Signage is not visible from the main road entrance

How to Fix It

1. 1

   Check the ABC-lataus app for the charger's exact location

   The app shows station details including photos or layout hints. Some ABC stations place chargers at the far end of the parking area, away from the fuel pumps.

2. 2

   Look for the CCS2 cable and charging unit

   The charger unit is taller than a fuel pump and usually has a clearly different design. Look for a separate bay with a CCS2 cable, often marked with green signage or an EV symbol on the ground.

3. 3

   Drive past the fuel pumps

   At many ABC stations, the EV charger is positioned after the fuel pump area or in a dedicated corner of the parking lot. Do not stop at the fuel pumps. Continue through and scan for the charging unit.

4. 4

   If an ICE vehicle is blocking the spot, report it

   ABC stations serve all types of vehicles. If a non-EV is parked in the charging bay, contact ABC customer service through the app. Unfortunately, there is not much you can do in the moment besides trying another station.

App setup confusion within the S-Group ecosystem

The ABC-lataus app is part of the S-Group digital ecosystem. If you already use S-mobiili for groceries or fuel, the relationship between the apps can be confusing.

Symptoms

• You are not sure whether to use S-mobiili or the ABC-lataus app
• Your S-Group login works in one app but not the other
• Charging payments do not appear in your S-mobiili transaction history
• You created a new account instead of linking your existing S-Group membership

How to Fix It

1. 1

   Use the ABC-lataus app for starting and managing charging sessions

   While S-mobiili handles your broader S-Group membership, the ABC-lataus app is the dedicated tool for finding stations, starting sessions, and viewing charging history. Install it separately from the App Store or Google Play.

2. 2

   Log in with your existing S-Group credentials

   Use the same username and password you use for S-mobiili or s-kanava.fi. Do not create a new account.

3. 3

   Check payment method settings in the ABC-lataus app

   Even if you have a payment card saved in S-mobiili, the ABC-lataus app may require you to add a payment method separately. Go to settings or payment in the ABC-lataus app and add your card there.

4. 4

   Verify your account is set up for charging

   Check the ABC-lataus app settings to make sure your payment method is saved and charging is enabled.

Connector stuck or difficult to insert in winter cold

Finnish winters mean temperatures well below freezing. The CCS2 connector locking mechanism and the vehicle's charge port can freeze, making it hard to plug in or unplug.

Symptoms

• The CCS2 connector will not click into your vehicle's charge port
• The connector is plugged in but the locking mechanism will not engage
• You cannot release the connector after charging is complete
• The connector handle feels stiff or the release button is frozen

How to Fix It

1. 1

   Check your vehicle's charge port for ice

   Open the charge port door and look for ice buildup around the opening or inside the port. Brush away any loose ice or snow with your hand or a soft brush. Do not use sharp tools, as you can damage the pins.

2. 2

   Warm the connector in your hands for a moment

   If the connector handle feels frozen stiff, hold it in your hands for 30 seconds to warm the mechanism slightly. The locking button and release lever work better when they are not frozen solid.

3. 3

   Push the connector in firmly and straight

   In cold weather, plastic contracts and tolerances get tighter. Line up the connector carefully and push it in with steady, even pressure. Do not force it at an angle.

4. 4

   If the connector is stuck after charging, try unlocking from your car

   Use your vehicle's unlock button or the in-car menu to release the charge port lock. Some vehicles also release the connector when you unlock the doors. If it is still stuck, wait a few minutes. The charging session generates heat that may free the mechanism.

5. 5

   Contact support if the connector will not release

   Do not yank the connector. Forcing it can damage both the cable and your vehicle's charge port. Call ABC-lataus support and they can guide you through a remote release or send help.

Charging session starts but power delivery is low

The charger is rated for 200 kW, but your session is delivering significantly less. Several factors specific to ABC-lataus stations can contribute.

Symptoms

• Dashboard shows 30 to 50 kW at a 200 kW rated charger
• Charging speed drops after a few minutes
• Speed is lower than what you get at other fast chargers
• The charger screen shows a lower maximum than 200 kW

How to Fix It

1. 1

   Check your vehicle's maximum DC charging rate

   A 200 kW charger does not mean your vehicle can accept 200 kW. Many EVs max out at 50 to 150 kW depending on the model, battery temperature, and state of charge. Check your vehicle's specifications.

2. 2

   Consider battery temperature in Finnish conditions

   Cold batteries accept less power. If your vehicle has been parked outside in freezing temperatures, the battery may need to warm up before it can accept higher charging speeds. Some vehicles have a preconditioning feature you can activate before arriving.

3. 3

   Check if another vehicle is sharing the station's power

   Some ABC-lataus locations share power between charger units. If another vehicle is charging at the same station, your available power may be split. This is normal and not a fault.

4. 4

   Arrive with a lower state of charge for faster charging

   Charging is fastest between 10% and 50% state of charge. If you arrive at 60% or higher, the charger will taper the power to protect your battery. This is your vehicle's doing, not the charger's.