Mercedes-Benz eVito Charging at Be Charge

Mercedes eVito Van Charger Will Not Start a Session

You have connected the charger to your Mercedes eVito and nothing is happening. No session, no power, no charging light. When you are between jobs or trying to charge at the depot, you need this resolved quickly. Here is how.

Symptoms

• CCS2 or Type 2 connector is plugged in but no session starts
• The MBUX display does not show charging activity
• The charger screen shows an error after plug-in
• The charge port indicator stays off or flashes amber
• The depot wallbox status light does not change when plugged in

What to Do

1. 1

   Authenticate before plugging in

   At public chargers, tap your RFID card or start the session in the app before inserting the connector. Wait for the charger to confirm it is ready.

2. 2

   Clean and reinsert the connector

   Remove the connector, wipe the charge port on the eVito with a dry cloth to remove any dirt, then reinsert the connector firmly until it clicks.

3. 3

   Check MBUX charging settings

   On the MBUX display, navigate to the charging menu. Check if departure time charging is active. Disable it for immediate charging.

4. 4

   Check the depot electrical panel

   If at the depot, check the circuit breaker for the charging circuit. Also check the wallbox status indicator. Report issues to your fleet manager.

5. 5

   Lock and unlock the van

   Use the key to lock the eVito, wait 20 seconds, then unlock. This can reset the charging electronics after a fault state.

6. 6

   Move to a different charger

   If the charger is faulty, do not waste time. Move to another unit or station, especially if you are mid-route.

Mercedes eVito Van Payment Failed at Charging Station

You are at a public charger with your Mercedes eVito and the payment will not go through. Whether it is a fleet card, personal RFID, or an app, payment failures at public chargers waste time between jobs. Here is how to resolve it fast.

Symptoms

• Fleet card does not start a session at the charger
• RFID card tap produces no response
• Charging app shows a payment authorization error
• Contactless bank card is declined
• Charger shows 'payment failed' on the screen

What to Do

1. 1

   Check accepted payment methods

   Look at the charger stickers and screen for accepted networks and cards. If your fleet card logo is not shown, this charger is not on your network.

2. 2

   Try a different payment method

   Switch between fleet card, personal RFID, charging app, and contactless bank card. One may work where others fail.

3. 3

   Verify fleet card status

   Contact your fleet manager or check the fleet card provider app to confirm the card is active and has not hit a spending limit.

4. 4

   Hold the card steadily

   Place the card flat against the reader for 3 seconds. Do not tap and pull away quickly. Gloves can interfere with NFC reading.

5. 5

   Cancel and retry

   Cancel any pending session in the app, wait 60 seconds, and start a fresh attempt.

6. 6

   Move to another charger unit

   If the payment reader on this unit is broken, try the next charger at the station. Do not waste time troubleshooting hardware you cannot fix.

Mercedes eVito Van Charging Slower Than Expected Speed

Your Mercedes eVito is charging slower than the 110 kW DC maximum. Or your depot wallbox is barely delivering power overnight. Without battery preconditioning, the eVito is especially sensitive to cold weather. Here is what to check and how to improve your charging speed.

Symptoms

• DC fast charging well below the 110 kW maximum
• Depot AC charging stuck at 3-4 kW instead of 11 kW
• Charging speed drops quickly after 40-50% state of charge
• Winter charging starts extremely slowly
• Mid-route DC charging takes too long between jobs

What to Do

1. 1

   Drive before charging in cold weather

   Since the eVito lacks preconditioning, drive for at least 20-30 minutes before stopping at a DC charger in winter. This warms the battery through use.

2. 2

   Charge between 20-50% for fastest speeds

   Plan your mid-route charging stops to arrive between 20-50% state of charge. This is where the eVito can approach its 110 kW peak.

3. 3

   Check your depot charger wiring

   Ask your fleet manager or electrician to verify the depot wallbox is wired for three-phase at 16A per phase for 11 kW. Single-phase installations are common but much slower.

4. 4

   Choose unshared DC chargers

   At public stations, check if the charger is sharing power. If another vehicle is on the paired connector, try a different unit.

5. 5

   Use MBUX to check charging status

   The MBUX infotainment system shows current charging power and estimated time. Use this to verify speeds and decide if you should move to a different charger.

6. 6

   Try a different charger

   If speeds remain well below expected at a low state of charge, the charger may be faulty. Move to another unit.