Mercedes-Benz eSprinter Charging at Be Charge

Mercedes eSprinter Van Charger Will Not Start Session

You have plugged in your Mercedes eSprinter and nothing is happening. Whether at the depot or a public charger mid-route, a session that will not start is a problem. The eSprinter uses standard CCS2 and Type 2 connectors, so the issue is usually authentication, settings, or the charger itself.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging session starts
• MBUX does not show any charging activity
• The charger screen shows an error after plug-in
• The charge port indicator does not light up
• Depot wallbox shows no activity when the eSprinter is connected

What to Do

1. 1

   Authenticate with the charger

   At public stations, tap your RFID or fleet card, or use the charging app before plugging in. Wait for the charger screen to confirm the session is starting.

2. 2

   Firmly reinsert the connector

   Remove the connector, check the charge port for dirt or debris, then reinsert it firmly until you hear the locking click.

3. 3

   Disable departure time charging

   In MBUX, go to the charging settings and turn off any departure time or scheduled charging. This allows immediate charging when you plug in.

4. 4

   Check depot charging queue

   If at the depot, check with your fleet manager whether load management is queuing your van. Some systems show queue status on the wallbox display.

5. 5

   Lock and unlock the eSprinter

   Lock the van with the key, wait 20 seconds, then unlock. This resets the charging system and can clear fault states.

6. 6

   Try a different charger

   If the charger cannot negotiate with the eSprinter's LFP battery system, try a newer or higher-rated charger. Some older 50 kW chargers have compatibility issues.

Mercedes eSprinter Van Payment Failed at the Charger

You are at a public charger with your Mercedes eSprinter and the payment is not going through. With a large van and a delivery schedule to keep, payment problems are the last thing you need. Here is how to resolve it quickly and get back on the road.

Symptoms

• Fleet charging card is declined at the charger
• RFID card does not register when tapped
• Charging app shows a payment or authorization error
• Contactless bank card is declined
• The charger screen shows an error and will not start the session

What to Do

1. 1

   Check which payments the charger accepts

   Read the stickers and screen on the charger. If your fleet card logo is not shown, the charger is not on your network.

2. 2

   Try an alternative payment method

   Use a personal RFID card, a different charging app, or a contactless bank card. Keep the receipt for reimbursement from your company.

3. 3

   Check fleet card status

   Contact your fleet manager or the card provider to verify the card is active and has not exceeded its spending limit.

4. 4

   Hold the card steadily for 3 seconds

   Place the card flat on the reader without moving. Remove gloves if wearing them. Some readers need a full 3-second contact to register.

5. 5

   Cancel any stuck sessions

   If a previous payment attempt is stuck, cancel it in the app and wait a minute before trying again.

6. 6

   Move to a different charger

   If the payment terminal is broken, try the next unit. Do not waste delivery time on a faulty card reader.

Mercedes eSprinter Van Charging Slower Than Expected

Your Mercedes eSprinter has a large 113 kWh LFP battery, which means charging sessions take longer than smaller vans even at peak speed. But if you are seeing speeds well below 115 kW on DC, something else is going on. Here is what to check.

Symptoms

• DC fast charging well below the 115 kW maximum
• Depot AC charging is slow with the large 113 kWh battery
• Charging speed drops sharply after 50-60% state of charge
• Cold weather charging starts at very low power
• A full DC charge takes significantly longer than expected

What to Do

1. 1

   Use navigation to precondition the battery

   Set the DC charger as your destination in the MBUX navigation. The eSprinter will precondition the LFP battery to the ideal temperature, which is critical for fast charging, especially in cold weather.

2. 2

   Plan charging stops for low state of charge

   Charge between 10-60% for the fastest DC speeds. With the LFP battery, the manufacturer generally allows charging to 100%, but the last 20% will be slow. Check your owner's manual for recommended charge limits.

3. 3

   Use high-power chargers

   Choose chargers rated 150 kW or higher to ensure the eSprinter can reach its 115 kW peak. On a 50 kW charger, a 113 kWh battery takes a very long time.

4. 4

   Upgrade depot chargers if needed

   For a 113 kWh battery, 11 kW three-phase AC is the minimum for reliable overnight charging. If your depot has single-phase or 7 kW chargers, discuss an upgrade with your fleet manager.

5. 5

   Avoid shared charger stalls

   At public stations, choose a charger where both connectors are free. With the eSprinter's large battery, shared power extends charging significantly.

6. 6

   Try a different charger

   If speeds are well below 80-90 kW at a low state of charge with a warm battery, the charger may be faulty. Try another unit.