Mercedes-Benz EQS Charging at ABC-lataus

Mercedes-Benz EQS Charger Won't Start a Session

You connected the CCS2 cable to your EQS's right rear charge port, but the Hyperscreen shows no charging activity. No power flowing, no progress. This is frustrating, especially in a flagship sedan where everything should just work. The cause is usually authentication, cable seating, or the charger itself, not the EQS.

Symptoms

• CCS2 connector plugged in but the Hyperscreen shows no charging activity
• Charger screen displays an error or stays idle after authentication attempt
• Plug & Charge does not authenticate automatically at a supported station
• Charge port LED does not illuminate or blinks an error pattern
• Mercedes me app shows the EQS as connected but not charging

What to Do

1. 1

   Remove and firmly reseat the CCS2 connector

   Pull the connector out of the right rear charge port. Check for debris or moisture. Push it back in straight and firm until you hear a click and see the charge port LED respond. The CCS2 connector is heavy, so support it with both hands to ensure proper alignment.

2. 2

   Authenticate manually if Plug & Charge failed

   Open the charging network's app and start the session by scanning the QR code or selecting the charger. If you have an RFID card for this network, tap it on the reader. Do not wait for Plug & Charge if it did not work within 30 seconds.

3. 3

   Disable scheduled charging in MBUX

   On the Hyperscreen, open Settings, then Charging. Turn off any departure time or scheduled charging window. At a public charger, you want charging to start immediately. Re-enable scheduled charging when you are back at your home wallbox.

4. 4

   Lock and unlock the EQS to reset the charge controller

   Use the key or Mercedes me app to lock the car. Wait 15 seconds, then unlock. This resets the charge port locking mechanism and the onboard charging communication module. Reconnect the cable after unlocking.

5. 5

   Try a different connector or charger at the station

   If the station has multiple CCS2 connectors, try a different one. If the entire station seems unresponsive, use MBUX navigation to find another nearby charger. Report the faulty charger through the network's app.

Mercedes-Benz EQS Payment Failed at Charging Station

You are standing next to your EQS at a public charger and payment will not go through. Plug & Charge did not activate, the app shows an error, or your card was declined. Payment failures are one of the most common reasons charging sessions do not start. With the EQS, you have multiple authentication options to try before giving up.

Symptoms

• Plug & Charge does not authenticate when the CCS2 cable is connected
• Contactless card declined at the charger's payment terminal
• Mercedes me Charge or the network's app shows a payment error
• RFID card not recognized by the charger reader
• Session starts but stops immediately with a billing-related error

What to Do

1. 1

   Try Plug & Charge by connecting the cable

   Plug the CCS2 connector into the EQS's right rear charge port. Wait up to 30 seconds for Plug & Charge to authenticate. Check the Hyperscreen for a charging confirmation. If nothing happens after 30 seconds, Plug & Charge is not working at this station.

2. 2

   Use the charging network's app to start the session

   Open the app for the charging network shown on the charger. Scan the QR code or enter the charger ID. Start the session through the app. Verify your payment method in the app is valid and not expired.

3. 3

   Try contactless payment at the charger terminal

   If the charger has a contactless payment terminal, tap your bank card, Apple Pay, or Google Pay. If the first card is declined, try a different one. Some terminals accept only certain card brands.

4. 4

   Verify your Mercedes me Charge account

   Open the Mercedes me app. Go to Charge settings and check that Plug & Charge is enabled and your payment method is current. If you recently changed your payment method, it may need time to sync. Try restarting the Mercedes me app.

5. 5

   Try a different RFID card or roaming provider

   If you carry multiple RFID cards, try another network. Roaming providers with broad European coverage (Chargemap, Maingau, Shell Recharge) can fill gaps where Mercedes me Charge does not reach.

6. 6

   Find an alternative charger nearby

   If payment fails on this charger entirely, use the Hyperscreen to find another station nearby. A different charging network may accept your payment method. Filter by the networks you know work with your cards.

Mercedes-Benz EQS Charging Slower Than Expected

You plugged in your EQS at a 300 kW charger expecting close to 200 kW, but the Hyperscreen shows 50 kW. Or your home wallbox is stuck at 3.6 kW instead of 11 kW (or 22 kW if you have the optional upgrade). The EQS has a huge 118 kWh battery that can take a while to warm up. Slow charging is almost always temperature, state of charge, or the charger, not a defect.

Symptoms

• DC fast charging speed well below the 200 kW maximum shown on the Hyperscreen
• AC charging stuck at 3-4 kW instead of 11 kW or 22 kW
• Charging speed drops sharply after reaching 50-60% state of charge
• Charging session starts at reasonable speed but slows within minutes
• The 118 kWh battery takes significantly longer to charge than expected

What to Do

1. 1

   Route to the charger using MBUX navigation

   Enter the charging station as your destination on the Hyperscreen or MBUX. This activates automatic battery preconditioning for the 118 kWh pack. The EQS will display a preconditioning notification. Given the large battery, start routing at least 20-30 minutes before arrival for maximum benefit in cold weather.

2. 2

   Check your state of charge before expecting peak speed

   The EQS reaches 200 kW only at lower state of charge levels. For the fastest DC charging, arrive between 10-20%. If you are above 60%, the speed reduction is normal. With 580 km of range, you often do not need to charge above 80% on road trips.

3. 3

   Verify the charger can deliver the speed you expect

   Check the charger's rated output on the unit itself or in the charging app. A 50 kW charger will never give your EQS more than 50 kW. Look for chargers rated 150 kW or higher to take advantage of the EQS's capabilities. Avoid stalls paired with another vehicle.

4. 4

   Check AC charging settings and wallbox compatibility

   Open the charging settings in MBUX. Confirm the charge current is set to maximum. If you have the optional 22 kW onboard charger, verify your wallbox is 3-phase 32A. For the standard 11 kW charger, you need at least 3-phase 16A.

5. 5

   Check if Plug & Charge negotiated the correct power

   The EQS supports Plug & Charge. Occasionally, authentication issues cause the charger to default to a lower power tier. Unplug from the right rear charge port, wait 30 seconds, and reconnect. Check MBUX for any authentication errors.

6. 6

   Try a different charger

   If the speed is still low after checking all settings, try a different charger. Some chargers degrade over time. Use MBUX navigation or the Mercedes me app to find a high-power charger (150 kW+) nearby.

Session fails to start or charger shows an error

You plug in and try to authenticate, but the charger does not begin charging. This can happen due to communication issues between your vehicle and the charger, or a problem with authentication.

Symptoms

• Charger shows an error after you try to start a session
• Contactless card payment does not work at this station (older unit without payment terminal)
• Card reader beeps but the session does not start
• The app says the session is starting but nothing happens at the charger

How to Fix It

1. 1

   Unplug, wait 30 seconds, and try again

   The initial communication handshake between your vehicle and the charger can fail. Unplug the connector, wait at least 30 seconds, and reconnect. The second attempt often works.

2. 2

   Try starting the session through the ABC-lataus app

   If the card reader is not cooperating, open the ABC-lataus app, select the station, and start the session from your phone. This bypasses the physical card reader entirely.

3. 3

   Try contactless card payment at newer stations

   Some newer ABC-lataus high-power stations have a contactless payment terminal. If the app is not cooperating, look for a card reader on the charger unit and tap your bank card. Older stations may not have this option.

4. 4

   Try a different charger unit at the same station

   If the station has multiple charger units, switch to another one. One unit may have a hardware issue while the others work fine.

Finding the EV charger at a busy fuel station

ABC-lataus chargers are located at ABC fuel stations, which also serve diesel and petrol vehicles. The EV charging spots can be easy to miss if you are visiting for the first time.

Symptoms

• You arrived at the ABC station but cannot see the EV charger
• The charger is behind the fuel pump area or in a separate parking section
• Other vehicles (non-EV) are parked in the charging spots
• Signage is not visible from the main road entrance

How to Fix It

1. 1

   Check the ABC-lataus app for the charger's exact location

   The app shows station details including photos or layout hints. Some ABC stations place chargers at the far end of the parking area, away from the fuel pumps.

2. 2

   Look for the CCS2 cable and charging unit

   The charger unit is taller than a fuel pump and usually has a clearly different design. Look for a separate bay with a CCS2 cable, often marked with green signage or an EV symbol on the ground.

3. 3

   Drive past the fuel pumps

   At many ABC stations, the EV charger is positioned after the fuel pump area or in a dedicated corner of the parking lot. Do not stop at the fuel pumps. Continue through and scan for the charging unit.

4. 4

   If an ICE vehicle is blocking the spot, report it

   ABC stations serve all types of vehicles. If a non-EV is parked in the charging bay, contact ABC customer service through the app. Unfortunately, there is not much you can do in the moment besides trying another station.

App setup confusion within the S-Group ecosystem

The ABC-lataus app is part of the S-Group digital ecosystem. If you already use S-mobiili for groceries or fuel, the relationship between the apps can be confusing.

Symptoms

• You are not sure whether to use S-mobiili or the ABC-lataus app
• Your S-Group login works in one app but not the other
• Charging payments do not appear in your S-mobiili transaction history
• You created a new account instead of linking your existing S-Group membership

How to Fix It

1. 1

   Use the ABC-lataus app for starting and managing charging sessions

   While S-mobiili handles your broader S-Group membership, the ABC-lataus app is the dedicated tool for finding stations, starting sessions, and viewing charging history. Install it separately from the App Store or Google Play.

2. 2

   Log in with your existing S-Group credentials

   Use the same username and password you use for S-mobiili or s-kanava.fi. Do not create a new account.

3. 3

   Check payment method settings in the ABC-lataus app

   Even if you have a payment card saved in S-mobiili, the ABC-lataus app may require you to add a payment method separately. Go to settings or payment in the ABC-lataus app and add your card there.

4. 4

   Verify your account is set up for charging

   Check the ABC-lataus app settings to make sure your payment method is saved and charging is enabled.

Connector stuck or difficult to insert in winter cold

Finnish winters mean temperatures well below freezing. The CCS2 connector locking mechanism and the vehicle's charge port can freeze, making it hard to plug in or unplug.

Symptoms

• The CCS2 connector will not click into your vehicle's charge port
• The connector is plugged in but the locking mechanism will not engage
• You cannot release the connector after charging is complete
• The connector handle feels stiff or the release button is frozen

How to Fix It

1. 1

   Check your vehicle's charge port for ice

   Open the charge port door and look for ice buildup around the opening or inside the port. Brush away any loose ice or snow with your hand or a soft brush. Do not use sharp tools, as you can damage the pins.

2. 2

   Warm the connector in your hands for a moment

   If the connector handle feels frozen stiff, hold it in your hands for 30 seconds to warm the mechanism slightly. The locking button and release lever work better when they are not frozen solid.

3. 3

   Push the connector in firmly and straight

   In cold weather, plastic contracts and tolerances get tighter. Line up the connector carefully and push it in with steady, even pressure. Do not force it at an angle.

4. 4

   If the connector is stuck after charging, try unlocking from your car

   Use your vehicle's unlock button or the in-car menu to release the charge port lock. Some vehicles also release the connector when you unlock the doors. If it is still stuck, wait a few minutes. The charging session generates heat that may free the mechanism.

5. 5

   Contact support if the connector will not release

   Do not yank the connector. Forcing it can damage both the cable and your vehicle's charge port. Call ABC-lataus support and they can guide you through a remote release or send help.

Charging session starts but power delivery is low

The charger is rated for 200 kW, but your session is delivering significantly less. Several factors specific to ABC-lataus stations can contribute.

Symptoms

• Dashboard shows 30 to 50 kW at a 200 kW rated charger
• Charging speed drops after a few minutes
• Speed is lower than what you get at other fast chargers
• The charger screen shows a lower maximum than 200 kW

How to Fix It

1. 1

   Check your vehicle's maximum DC charging rate

   A 200 kW charger does not mean your vehicle can accept 200 kW. Many EVs max out at 50 to 150 kW depending on the model, battery temperature, and state of charge. Check your vehicle's specifications.

2. 2

   Consider battery temperature in Finnish conditions

   Cold batteries accept less power. If your vehicle has been parked outside in freezing temperatures, the battery may need to warm up before it can accept higher charging speeds. Some vehicles have a preconditioning feature you can activate before arriving.

3. 3

   Check if another vehicle is sharing the station's power

   Some ABC-lataus locations share power between charger units. If another vehicle is charging at the same station, your available power may be split. This is normal and not a fault.

4. 4

   Arrive with a lower state of charge for faster charging

   Charging is fastest between 10% and 50% state of charge. If you arrive at 60% or higher, the charger will taper the power to protect your battery. This is your vehicle's doing, not the charger's.