Kia EV9 Charging at Atlante

Kia EV9 Charger Won't Start? Step-by-Step Fix Guide

You have plugged the cable into your EV9's right rear charge port, but nothing is happening. No charging indicator on the panoramic display, no LED confirmation. On a large SUV you rely on for family trips or long drives, a failed charge start can be stressful. In most cases, the issue is authentication, utility mode being on, a car setting, or the charger itself.

Symptoms

• CCS2 or Type 2 cable plugged in but no charging indicator on the panoramic display
• Charge port LED stays off or flashes red
• Charger screen shows an error or remains on the start screen
• Kia Connect app shows the car is not connected to a charger
• Charging starts briefly then stops within a few seconds

What to Do

1. 1

   Turn off V2L utility mode

   On the EV9's infotainment screen, go to EV settings. Make sure utility mode or V2L is turned off. Also check the exterior V2L outlet on the rear bumper. If a device was plugged in there, the car may still be in discharge mode.

2. 2

   Check the charge port and cable

   Open the charge port on the right rear fender. The EV9 is a tall vehicle, so the port is relatively high. Press the flap firmly to open. Insert the CCS2 connector straight in until it clicks. The LED should light up.

3. 3

   Authenticate with the charger

   If Plug & Charge does not start the session, tap your RFID card, use the charging network's app, or try contactless payment. Have a backup method ready.

4. 4

   Check for a charging schedule

   On the infotainment screen, go to EV settings, then Scheduled Charging. If a schedule is active, disable it or tap 'Charge Now' to override. The Kia Connect app can also manage schedules.

5. 5

   Unplug, wait 30 seconds, and try again

   Remove the cable completely, wait 30 seconds, reconnect, and re-authenticate. This resets the communication between the EV9 and the charger.

6. 6

   Try a different charger

   If nothing works, try another stall at the same station or a different station. Report the broken charger through the charging network's app.

Kia EV9 Charger Payment Failed at a Public Station

You are at a public charger with your EV9, the CCS2 cable is connected, but the payment will not go through. The charger shows an error, the app is not cooperating, or your RFID card gets nothing. Payment problems are one of the most common reasons charging fails to start, and they are almost never a car problem. Here is how to work through it.

Symptoms

• Charger screen shows 'payment failed' or 'authorization error'
• RFID card tapped but the charger does not respond
• Charging network app shows an error during authorization
• Plug & Charge does not start the session automatically
• Contactless card payment declined at the terminal

What to Do

1. 1

   Try a different payment method

   If RFID failed, try the charging network's app. If the app failed, try contactless payment with a card. Switch between methods quickly rather than retrying the same one.

2. 2

   Check your charging network account

   Open the charging app and check your payment details. Look for expired cards, low prepaid balances, or account issues. Update your payment method if needed.

3. 3

   Verify Plug & Charge configuration

   In the Kia Connect app, check that Plug & Charge is enabled and linked to the correct charging network. Also verify that this specific station supports Plug & Charge. Not all stations do.

4. 4

   Look for a QR code on the charger

   Many chargers have a QR code that opens a web payment page. This lets you pay without an account or app. Scan it with your phone camera.

5. 5

   Try a different charger at the same station

   If one stall's payment terminal is not working, another may be fine. Walk to the next charger and try your payment method again.

Kia EV9 Charging Slower Than Expected at DC or AC

The EV9 is Kia's largest electric SUV, with a 96 kWh battery and 800V architecture that supports up to 233 kW DC charging. When you see 60 kW on the charger screen instead of 200+, it does not match what the specs promise. In most cases, slow charging on the EV9 comes down to battery temperature, the charger's actual voltage and output, or a car setting worth checking.

Symptoms

• DC fast charging speed well below the 233 kW maximum
• AC charging stuck at 3-4 kW instead of the full 11 kW
• Charging speed drops sharply above 60-70% state of charge
• Session starts at low power and never ramps up
• Panoramic display shows much lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature

   Look at the EV information on the panoramic display. If the battery is cold, use the built-in navigation to set a charging destination. The EV9 will precondition the battery automatically on the way. This is especially important in winter given the large battery.

2. 2

   Check whether the charger supports 800V

   Look at the charger specs on its screen or in the charging network's app. If it is a 400V charger, the EV9's multi-charging system handles the conversion, but you will not see 233 kW. Seek out chargers that explicitly list 800V support.

3. 3

   Check your state of charge

   If you are above 80%, the speed drop is normal. For road trips, plan stops to arrive between 10-20% and unplug at 80%. The EV9's consumption is around 204 Wh/km, so factor that into your stop planning.

4. 4

   Review scheduled charging and charge limits

   On the EV settings screen or in the Kia Connect app, check that scheduled charging is not delaying the session and the charge current limit is at maximum.

5. 5

   Check if the charger is sharing power

   Look at the charger cabinet. If two cables come from the same unit and someone is on the other cable, your speed may be halved. Move to an unoccupied charger if one is available.

6. 6

   Try a different charger or station

   If speed is still low after checking everything, the charger may be underperforming its rated output. Try another stall or head to a different station.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.