BYD SEAL Charging at REWE Charging

BYD Seal Charger Won't Start? Step-by-Step Fix

You have plugged in your BYD Seal but the charger refuses to start. Screen errors, no response, or the car is not acknowledging the connector. With the Seal's 800V system, the charging handshake is slightly more complex, but most failed starts have simple causes. Let's work through them.

Symptoms

• Charger display shows an error or stays on the authentication screen
• CCS2 connector clicks in but no charging activity begins
• BYD Seal dashboard shows no charging indicator
• Charger starts the handshake but then aborts with an error
• Type 2 AC cable connected but no power flowing

What to Do

1. 1

   Read the charger display

   Check for error messages, authentication prompts, or fault indicators. If it says 'communication error' after a brief attempt, the charger may be struggling with the 800V handshake.

2. 2

   Unplug and replug the connector

   Remove the CCS2 connector completely, wait 15 seconds, and reinsert it firmly. Make sure it locks into the Seal's charge port with an audible click.

3. 3

   Complete authentication

   Tap your RFID card, start the session in the network app, or use contactless payment. Try both pre-plug and post-plug authentication sequences.

4. 4

   Inspect the charge port

   Check the Seal's charge port for debris, ice, or visible damage. Clean gently if needed. Make sure the port flap is fully open.

5. 5

   Restart the car's systems

   Turn the BYD Seal off completely, wait 30 seconds, then turn it back on. This resets the charging communication system and can resolve handshake issues.

6. 6

   Try a different charger

   If this stall consistently fails, try another one. For persistent 800V handshake issues, look for newer generation chargers (2022 or later installations) which tend to have better protocol support.

BYD Seal Charging Payment Failed? How to Fix It

You are at a charger with your BYD Seal and the payment will not work. Your card is rejected, the app is not cooperating, or you cannot figure out how to pay at this station. Payment issues are frustratingly common across European charging networks. Here is how to sort it out and start charging.

Symptoms

• RFID card gets no response when tapped
• Charging app shows payment error or transaction declined
• Contactless bank card declined at the charger
• Charger displays authentication required but does not accept your method
• Session terminates immediately due to billing failure

What to Do

1. 1

   Check the charger's accepted payment methods

   Look for logos, stickers, and instructions on the charger showing which RFID cards, apps, or bank card types it accepts.

2. 2

   Use the network's own app

   Scan the QR code on the charger or search for the network's app. Register, add a payment method, and start the session through the app.

3. 3

   Try different payment methods

   Switch between RFID, contactless, and app payment. A roaming provider like Plugsurfing, Shell Recharge, or Chargemap may cover this charger.

4. 4

   Check your bank for blocked transactions

   Open your banking app to check for declined pre-authorizations. Call your bank if needed, or try a card with a higher available balance.

5. 5

   Try another stall

   The payment reader on one stall may be broken while others work. Try the next stall before leaving the station.

6. 6

   Find an alternative station

   If nothing works, search for a nearby station on a network where your payment methods work. Filter by network or payment type in your app.

BYD Seal Charging Slowly? 800V LFP Explained Here

Your BYD Seal has an impressive 150kW DC capability and 800V architecture, but you are not seeing those numbers on the charger display. The Seal uses an LFP battery, which is safe to charge to 100% daily but is significantly more sensitive to cold than NMC chemistry. Without preconditioning, winter charging can be frustratingly slow. Here is what affects your speed and how to improve it.

Symptoms

• DC charging power well below 150kW even on a high-power charger
• Dramatically slow charging in cold weather, sometimes under 30kW
• AC charging not reaching 11kW
• Charging speed tapers heavily above 60-70% SOC
• 800V charger delivers no better speed than a 400V one

What to Do

1. 1

   Check the temperature

   If it is below 10C, cold is the primary cause of slow LFP charging. Below 0C, expect speeds to be a fraction of the 150kW maximum. Plan for longer stops in winter.

2. 2

   Drive longer before charging in cold weather

   Without preconditioning, the only way to warm the Seal's LFP battery is to drive. Highway driving for 30-45 minutes before a DC stop will significantly improve initial charging speed.

3. 3

   Look for high-power chargers

   To access the Seal's 150kW capability, you need a charger rated at 150kW or above. Check the charger label or app. Many older CCS2 stations max out at 50kW.

4. 4

   Arrive at a lower SOC

   The Seal charges fastest between 10-50% SOC. Plan road trip stops to arrive between 10-20% for maximum speed. The taper above 70% is significant.

5. 5

   Avoid power-sharing stalls

   Choose a charger stall where no other car is using the paired stall. This gives you the full power allocation from the station.

6. 6

   For AC charging, use a 3-phase connection

   The Seal supports 11kW AC via Type 2. A single-phase cable or charger limits you to about 3.6kW. Use a 3-phase Type 2 cable on an 11kW or higher charger.

Charger occupied by non-charging vehicles

You arrive at the REWE charger and a car is parked in the charging spot without being plugged in. This is common at supermarket locations where shoppers treat EV spots as regular parking.

Symptoms

• Charging spot is occupied by a car with no cable connected
• ICE vehicle parked in the EV charging bay
• Car is plugged in but session has clearly ended and the driver is inside shopping
• All charging spots taken despite the app showing the charger as available

How to Fix It

1. 1

   Check if the other car is actively charging

   Look at the charger display or connector. If the session has ended and the car is just parked, REWE cannot remotely move it. The app status reflects the charger, not the parking spot.

2. 2

   Ask at the REWE customer service desk

   REWE staff can sometimes make a store announcement asking the vehicle owner to move. This works more often than you would expect.

3. 3

   Wait briefly or shop first

   At supermarket chargers, turnover is high. Most shoppers leave within 30 to 45 minutes. Do your shopping and check again.

4. 4

   Check for additional REWE locations nearby

   Many German cities have multiple REWE stores with chargers within a short drive. Check the app for the next closest option.

Contactless card reader not responding

You tap your debit or credit card on the reader but nothing happens. The reader does not beep, does not show a light, or shows an error briefly before resetting.

Symptoms

• Card reader shows no response when you tap
• Reader beeps but the screen shows an error
• Card works at the REWE checkout inside but not at the charger
• Contactless symbol is visible on the reader but it seems inactive

How to Fix It

1. 1

   Hold your card flat against the reader for 3 to 5 seconds

   Some REWE charger readers are slower than store payment terminals. Hold the card still and wait for the full processing time.

2. 2

   Remove your phone and other cards from the area

   If you hold your wallet with multiple contactless cards near the reader, it may detect interference and reject the transaction.

3. 3

   Try the charging app instead

   If contactless is not working, start the session through the REWE charging partner app. This bypasses the physical card reader entirely.

4. 4

   Check if the reader is physically damaged

   Supermarket chargers are exposed to shopping carts, weather, and heavy foot traffic. If the reader looks cracked or the screen is damaged, report it to REWE staff inside and try another stall if available.

Session ends due to maximum stay time limit

Your charging session stops before the battery is full because REWE enforces a maximum parking time at the charging spot. This exists to keep spots available for other shoppers.

Symptoms

• Charging stops after 60 to 90 minutes even though the battery is not full
• App notification says session ended due to time limit
• You return from shopping to find the charger disconnected
• Charger screen shows session completed despite low battery level

How to Fix It

1. 1

   Check the posted time limit before you start

   REWE typically allows 60 to 120 minutes depending on the location. Look for signage near the charger or check the app for time restrictions at that specific store.

2. 2

   Plan your charge around your shopping time

   At up to 300 kW, most EVs can gain 150 to 250 km of range in 30 to 45 minutes. A normal grocery run is usually enough time for a meaningful charge.

3. 3

   Move your car if you need more time

   If you need a longer session, move your car to a regular parking spot after the time limit and start a new session if the charger is free when you return.

4. 4

   Use REWE chargers for top-ups, not full charges

   Supermarket chargers work best for adding range while you shop, not for charging from 10% to 100%. If you need a full charge, plan for a dedicated fast charging station.

Poor mobile signal in underground or garage parking

Some REWE stores have chargers in basement or covered parking areas where mobile signal is weak. This can prevent the app from starting a session or processing contactless payments.

Symptoms

• App shows 'No connection' or spins without loading
• Contactless payment times out during processing
• You cannot scan the QR code on the charger because the page will not load
• Session starts but the app loses connection and cannot show charging status

How to Fix It

1. 1

   Connect to REWE store WiFi if available

   Many REWE stores offer free WiFi that may reach the parking area. Check for a REWE network in your phone's WiFi settings.

2. 2

   Walk closer to the garage entrance to start the session

   If you need the app to start the session, walk toward the exit where signal is stronger, start the session remotely, then return to your car.

3. 3

   Use contactless payment instead of the app

   Contactless card payments are processed through the charger's built-in connection, not your phone. If the card reader works, you do not need mobile signal.

4. 4

   Pre-load the app before entering the garage

   Open the app and navigate to the station page while you still have signal. Some apps cache enough data to start a session even with intermittent connectivity.

Charger unavailable outside store hours

You arrive at a REWE charger outside store opening hours and the charger is inaccessible or powered down. Some locations gate their parking areas or shut down chargers when the store closes.

Symptoms

• Parking area gate is locked and you cannot reach the charger
• Charger screen is dark and does not respond
• App shows the charger as available but the physical location is closed
• Barrier arm blocks entry to the parking lot after closing time

How to Fix It

1. 1

   Check store hours before planning a charge

   REWE stores in Germany typically close between 20:00 and 22:00 on weekdays and earlier on Saturdays. Most are closed on Sundays. If the charger is behind a gate, you cannot access it outside these hours.

2. 2

   Verify 24/7 access in the app

   Some REWE charging locations offer 24/7 access even when the store is closed. Check the station details in the app. If it does not mention 24-hour access, assume it follows store hours.

3. 3

   Leave the parking area before the store closes

   If you are charging and the store is about to close, make sure you can exit the parking area. Some locations lock the barrier after closing, which could trap your car overnight.

4. 4

   Find an alternative nearby charger

   Use a multi-network app like Chargemap or the EVcourse charger finder to locate a 24/7 charger nearby. Dedicated charging stations along main roads usually operate around the clock.