BYD ATTO 3 Charging at BP Pulse

BYD ATTO 3 Charger Won't Start? Fix It Step by Step

Your BYD ATTO 3 is plugged in but charging has not started. The charger might be blinking, showing an error, or completely unresponsive. This happens to every EV driver eventually. Walk through these steps to figure out whether the problem is the charger, the car, or something in between.

Symptoms

• Charger display shows an error code after plugging in
• CCS2 connector is inserted but the ATTO 3 does not respond
• Charging port indicator light stays off or flashes a warning color
• Charger screen says 'waiting for vehicle' indefinitely
• Type 2 AC cable locks in but no power flows to the car

What to Do

1. 1

   Check the charger screen for instructions

   Read any error messages or prompts on the charger display. It will tell you if authentication is needed, if there is a fault, or if it is waiting for the vehicle to respond.

2. 2

   Remove and reinsert the connector

   Pull the CCS2 or Type 2 connector out completely, wait 10-15 seconds, and push it back in firmly until you hear the locking click.

3. 3

   Authenticate with the charger

   Tap your RFID card, open the network's app to start the session, or try contactless payment. If one method fails, try another.

4. 4

   Check the charge port for obstructions

   Look inside the ATTO 3's charge port for debris, dirt, water, or ice. Clean it gently if needed. Make sure the flap is fully open and not interfering with the connector.

5. 5

   Lock and unlock the car

   Use the BYD app or key to lock and then unlock the ATTO 3. This can reset the charge port locking mechanism and communication system.

6. 6

   Try a different charger

   If nothing works, try another stall or station. If another car can charge at the same stall, the issue may be specific to your ATTO 3 and worth a service visit.

BYD ATTO 3 Charging Payment Failed? Quick Fixes

You have your BYD ATTO 3 plugged in and ready, but the payment will not go through. Card rejected, app error, or you simply cannot figure out how to pay at this charger. Payment problems prevent more charging sessions than most people realize. Here is how to solve it.

Symptoms

• RFID card tap gets no response from the charger
• Charging app shows payment declined or error
• Contactless bank card rejected at the charger terminal
• Charger prompts for payment but nothing you try works
• Session starts then terminates within seconds due to billing failure

What to Do

1. 1

   Check accepted payment methods on the charger

   Look for payment logos, QR codes, and instructions on the charger unit. This tells you which RFID cards, apps, or bank card types work here.

2. 2

   Download and use the network's app

   Scan the QR code or search for the network's app. Create an account, add your card, and start the session through the app. This often works when RFID fails.

3. 3

   Try a different payment method

   Switch between RFID card, app payment, and contactless bank card. If you have a roaming provider, try that. Having multiple options greatly increases your chances.

4. 4

   Check for bank holds or declines

   Open your banking app to see if a pre-authorization was attempted and declined. Contact your bank if needed, or try a different card with sufficient available balance.

5. 5

   Try another stall at the station

   If the card reader is broken on one stall, the next one might work fine. Try the adjacent stall before leaving.

6. 6

   Find a nearby alternative station

   Use your charging app to find another station nearby where your payment methods are known to work. Filter by network if possible.

BYD ATTO 3 Charging Slowly? LFP Cold Tips Inside

Your BYD ATTO 3 is charging much slower than the 89kW you expected. The ATTO 3 uses an LFP battery, which is great for longevity and safe to charge to 100% daily, but LFP is significantly more sensitive to cold temperatures than NMC chemistry. Without preconditioning, cold weather hits especially hard. Here is what is going on and what you can do.

Symptoms

• DC charging power well below 89kW on the charger display
• Extremely slow charging in cold weather, sometimes under 20kW
• AC charging not reaching 11kW
• Charging speed drops sharply above 60-70% SOC
• First charge of the day in winter is dramatically slower than summer

What to Do

1. 1

   Check the outside temperature

   If it is below 10C, your LFP battery is likely too cold for fast charging. Below 0C, expect significantly reduced speeds. This is the most common cause of slow charging on the ATTO 3.

2. 2

   Drive longer before charging in cold weather

   Since the ATTO 3 has no preconditioning, drive for at least 30-45 minutes, ideally on a highway, before stopping at a DC charger. This warms the LFP battery through use.

3. 3

   Check the charger's rated power

   Verify the charger can deliver at least 89kW. A 50kW charger limits your speed regardless of battery temperature. Look for chargers rated 100kW or above.

4. 4

   Arrive at a lower SOC

   The ATTO 3 charges fastest between 10-50% SOC. On road trips, plan to arrive at each charger between 10-20% for the best speed.

5. 5

   Choose a stall without power sharing

   Pick a stall where the adjacent one is empty to avoid power sharing. Some stations label which stalls share power output.

6. 6

   For AC, use a 3-phase Type 2 connection

   The ATTO 3 supports 11kW AC charging. Ensure your cable and charger are both 3-phase capable. A single-phase connection limits you to about 3.6kW.

Contactless reader not responding

You tap your bank card or phone and nothing happens. The screen does not acknowledge the tap at all, or it briefly flashes and returns to the start screen.

Symptoms

• No beep or screen change after tapping your card
• Screen flashes 'Card read error' then resets
• Apple Pay or Google Pay shows 'Done' on your phone but the charger does not start
• Reader works on one unit but not the adjacent one

How to Fix It

1. 1

   Try a physical bank card instead of your phone

   Contactless phone payments sometimes fail on BP Pulse readers even when a physical card works fine. Hold the card flat against the reader for 2-3 seconds.

2. 2

   Check for a second tap point

   Some BP Pulse units have the contactless reader on the side panel rather than below the screen. Look for a card symbol printed on the housing.

3. 3

   Clean the reader surface

   Wipe dirt, rain, or condensation off the contactless reader area with your sleeve. Moisture on the sensor can prevent a clean read.

4. 4

   Start the session via the BP Pulse app instead

   Open the app, find the charger on the map, select the connector, and tap 'Start Charging.' This bypasses the physical reader entirely.

5. 5

   Try the other connector or an adjacent unit

   If the charger has two connectors, the other side may have a working reader. Or walk to the next unit. Contactless reader failures are often limited to one specific unit.

BP Pulse app crashing on Android

The app closes unexpectedly when you try to start a session, view the map, or enter payment details. This is more common on older Android versions and after recent app updates.

Symptoms

• App closes immediately after opening
• App freezes on the map screen then crashes
• Crash when tapping 'Start Charging' after selecting a connector
• 'App keeps stopping' notification from Android

How to Fix It

1. 1

   Force close and reopen the app

   Go to Android Settings, then Apps, then BP Pulse. Tap 'Force Stop,' wait a few seconds, then open the app again.

2. 2

   Clear the app cache

   In Settings, go to Apps, then BP Pulse, then Storage, then 'Clear Cache.' This removes temporary data without deleting your account. You will not need to log in again.

3. 3

   Check for an app update

   Open the Google Play Store, search for BP Pulse, and tap 'Update' if available. Crashes often follow a buggy release that gets patched within days.

4. 4

   Use contactless payment as a backup

   If the app will not cooperate, tap your bank card on the charger's contactless reader to start a session without the app.

5. 5

   Reinstall the app if crashes persist

   Uninstall BP Pulse, restart your phone, then reinstall from the Play Store. You will need to log in again, so make sure you know your BP Pulse account email.

Charger shows 'Out of Service' with no visible damage

The screen displays 'Out of Service' or 'Unavailable,' but the charger looks perfectly fine. No broken cables, no barrier tape, no obvious reason it should be offline.

Symptoms

• Screen stuck on 'Out of Service' message
• Charger appears available in the app but shows error on arrival
• Status light is red or off entirely
• Other chargers at the same location work fine

How to Fix It

1. 1

   Check the BP Pulse app for real-time status

   Open the app and look at this specific charger. If it shows as unavailable there too, the network has flagged it remotely. A maintenance team likely already knows.

2. 2

   Look for a reset button or power switch

   Some older BP Pulse units (especially former Chargemaster ones) have a small reset button behind a panel or near the base. Pressing it can sometimes clear a stuck error state.

3. 3

   Report it in the app

   Use the 'Report a problem' option on the charger's detail page in the BP Pulse app. This helps BP Pulse prioritize repairs and updates the status for other drivers.

4. 4

   Move to another charger

   An 'Out of Service' state usually means a backend fault, a communication issue with the network, or a pending software update. You cannot fix these yourself. Use another unit or location.

Charging session drops after 5-10 minutes

Charging starts normally, but the session ends on its own after a few minutes. Your car shows it is no longer receiving power, and the charger returns to the welcome screen.

Symptoms

• Car dashboard shows charging stopped unexpectedly
• Charger screen returns to 'Plug in to start' after a few minutes
• You receive a session-ended notification in the app with a very short session
• This happens repeatedly at the same charger

How to Fix It

1. 1

   Check the connector is fully seated

   Unplug the cable, inspect the connector pins for dirt or debris, and plug it back in firmly until you hear a click. A loose connection can cause the charger to drop the session.

2. 2

   Check your car's charge limit

   If your car's charge limit is set very close to the current battery level, some vehicles will stop charging almost immediately. Set the limit to 80% or higher and try again.

3. 3

   Try the other connector type

   If the charger offers both CCS2 and CHAdeMO and your car supports CCS2, make sure you are using CCS2. Using the wrong connector obviously will not fit, but a worn CCS2 connector on one side may work better on the other unit.

4. 4

   Start a new session at a different unit

   Repeated drops at the same charger point to a hardware fault on that unit. Move to another charger and try again.

5. 5

   Report the faulty unit

   Note the charger ID (printed on the unit) and report it via the BP Pulse app or call the BP Pulse support number shown on the charger. This helps get the unit serviced.

Subscription vs pay-as-you-go pricing confusion

BP Pulse offers a subscription plan with lower per-kWh rates and a pay-as-you-go option with higher rates. It is not always clear which pricing you are on, or whether the subscription is worth it for your usage.

Symptoms

• Charged a higher rate than expected on your receipt
• Unsure whether your subscription is active
• Signed up for subscription but still seeing non-member prices
• Cannot figure out how to switch between plans

How to Fix It

1. 1

   Check your plan status in the app

   Open the BP Pulse app, go to your account settings, and look for your subscription status. If it says 'Active,' you should be getting the lower rate automatically.

2. 2

   Make sure you are starting sessions through the app

   Subscription pricing only applies when you start the session via the BP Pulse app or RFID card linked to your account. Tapping a contactless bank card will charge you the standard pay-as-you-go rate.

3. 3

   Review your charging history for rate discrepancies

   In the app, go to Charging History and check the per-kWh rate on recent sessions. Compare this to the subscription rate listed on the BP Pulse pricing page.

4. 4

   Cancel or change your plan if needed

   You can manage your subscription in the app under Account, then Subscription. If you charge infrequently, pay-as-you-go may actually cost less overall despite the higher per-kWh rate.