Audi Q4 e-tron Charging at Atlante

Audi Q4 e-tron Charger Won't Start Charging

You have plugged in your Q4 e-tron, the connector clicked into the charge port on the right rear fender, but nothing happens. The MMI screen stays silent or shows an error. This is frustrating, but it is almost always fixable on the spot without calling roadside assistance.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the MMI touchscreen
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• Q4 e-tron charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Instrument cluster briefly shows a charging icon, then it disappears

What to Do

1. 1

   Check for a charging schedule or departure timer

   On the MMI touchscreen, go to the e-tron charging settings. If a timer or departure schedule is active, switch it to charge immediately or turn off the timer. You can also check the myAudi app for active schedules.

2. 2

   Unplug and reconnect firmly

   Open the charge port on the right rear fender using the button on the port or through the MMI screen. Remove the connector, wait 10 seconds, then reinsert it firmly until you hear a clear click. Watch the charge port LED for a steady response.

3. 3

   Restart the charger session

   On the charger, end the current session if one is active. Then start a new session by tapping your RFID card, using contactless payment, or restarting in the charger operator's app.

4. 4

   Try Plug & Charge or a different payment method

   If your Q4 e-tron has Plug & Charge set up through the myAudi app, make sure the charger supports it. Otherwise, switch to a different RFID card, contactless payment, or the charger operator's own app.

5. 5

   Reboot the MMI system

   Press and hold the power button on the MMI touchscreen for about 10 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication on the car's side.

6. 6

   Try a different charger or cable

   If the station has multiple stalls, move to a different one. If you are at an AC charger with your own cable, try a different cable. A faulty charger is more common than a faulty car.

Audi Q4 e-tron Charging Payment Failed at Station

You are at the charger, your Q4 e-tron is plugged in, but the payment will not go through. The charger shows an error or just sits there waiting. Payment failures at public chargers are common and usually have nothing to do with your car. Here is how to get charging.

Symptoms

• Charger displays 'Payment failed' or 'Authorization error' after tapping your card
• RFID card is not recognized by the charger's reader
• myAudi or Audi charging app shows an error when trying to start a remote session
• Plug & Charge does not activate after plugging in the CCS2 connector
• Contactless payment terminal on the charger rejects your bank card

What to Do

1. 1

   Try a different payment method

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having two or three payment options gives you the best chance of getting going.

2. 2

   Check the myAudi app

   Open the myAudi app on your phone. Make sure your Audi charging account is active, your payment method is valid, and Plug & Charge is enabled if you want to use it. Try starting the session remotely through the app.

3. 3

   Scan the charger's QR code

   Most public chargers have a QR code on the unit. Scanning it with your phone's camera opens the operator's payment page. You can usually pay with a credit card through the browser without downloading an app.

4. 4

   Check your bank app for blocked transactions

   Open your banking app and check for any flagged or blocked transactions. Some banks require you to approve the charge manually. If you see a notification, approve it and try the payment again.

5. 5

   Try Plug & Charge if available

   If the charger supports Plug & Charge and your Q4 e-tron has it activated through the myAudi app, simply unplug and replug the CCS2 connector. The payment should authorize automatically through the cable without any card or app.

6. 6

   Move to a different charger

   If nothing works at this station, the charger's payment system may be down entirely. Find a nearby alternative using the myAudi app or the Q4 e-tron's built-in charger finder on the MMI touchscreen.

Audi Q4 e-tron Charging Slower Than Expected

You plugged in your Q4 e-tron expecting 135 kW and the MMI touchscreen shows 30 kW. Or your home wallbox is stuck at 3 kW instead of the full 11 kW. Slow charging on the Q4 e-tron is almost never a defect. It is usually the battery temperature, the charger itself, or a setting in the MMI system you can fix right now.

Symptoms

• DC fast charging speed well below the 135 kW maximum shown on the MMI touchscreen
• AC home charging stuck at 3-4 kW instead of the full 11 kW
• Charging speed drops significantly after reaching 50-60% state of charge
• Charging session starts at a reasonable speed but drops quickly within minutes
• MMI display shows lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature

   Look at the charging screen on the MMI touchscreen. If the battery is cold, use the navigation system to route to the fast charger. The Q4 e-tron will precondition the battery automatically on the way. If you are already at the charger, driving for 15-20 minutes and returning can help.

2. 2

   Check your state of charge

   Look at the digital instrument cluster or MMI screen. If you are above 80%, the slower speed is expected. For the fastest charging, arrive at the charger between 10-20% and charge to 80%.

3. 3

   Verify the charger is not sharing power

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

4. 4

   Check the AC charge current setting

   On the MMI touchscreen, go to the charging settings menu. Make sure the AC charge current is set to maximum. On the Q4 e-tron, this is under the e-tron charging section in the vehicle settings.

5. 5

   Check for software updates

   On the MMI touchscreen, check for available updates, or use the myAudi app to see if an over-the-air update is ready. Audi has released updates that improve the Q4 e-tron's DC charging curve on the MEB platform.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Try a different stall at the same location or a different charging station entirely.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.