Volkswagen ID.3 Charging at Recharge

Volkswagen ID.3 Charger Will Not Start a Session

You plugged in your ID.3 and the charger just sits there. No power, no animation on the infotainment screen, nothing happening. Whether you are at a public DC fast charger or an AC destination charger, there are a few specific things to check before giving up on this station.

Symptoms

• CCS2 connector is plugged into the right rear charge port but the charger shows 'Waiting'
• Infotainment screen shows no charging activity after connecting the cable
• Charger display says 'Authorization required' even though you tapped your card
• Charge port LED on the right rear does not change color after plugging in
• We Charge or Elli app shows the car as connected but not charging

What to Do

1. 1

   Unplug and reseat the CCS2 connector

   Remove the connector from the right rear charge port completely. Wait five seconds. Reinsert it firmly until you hear the latch click. Make sure the two DC pins at the bottom of the CCS2 plug are aligned and fully engaged.

2. 2

   Authorize the session manually

   Check the charger display. If it says 'Waiting for authorization' or similar, tap your RFID card on the reader, open the charger operator's app, or use contactless payment. Do not assume Plug & Charge will work unless you have confirmed it is active.

3. 3

   Check for scheduled charging in the infotainment

   On the ID.3's infotainment screen, go to the charging settings. Look for departure timer or scheduled charging. If it is active, disable it or select 'Charge Now' to start immediately.

4. 4

   Verify Plug & Charge setup in the We Charge app

   Open the We Charge or Elli app on your phone. Check that Plug & Charge is enabled and your payment method is valid. If Plug & Charge has never been set up, you will need to authorize sessions manually at every charger.

5. 5

   Restart the infotainment system

   Press and hold the power button on the infotainment screen for about 10 seconds until it goes black. Wait for it to restart. This can resolve communication glitches between the ID. Software and the charger without affecting the car's other systems.

6. 6

   Try a different charger or connector

   If the session still will not start, the charger may be faulted. Try a different connector at the same station, or find a nearby alternative using the We Charge app or the ID.3's built-in charger finder.

Volkswagen ID.3 Payment Failed at Charging Station

You are at the charger, your ID.3 is plugged in, but the payment will not go through. The charger shows an error or just sits there waiting for authorization. Payment problems at public chargers are common, and they usually have nothing to do with your car. Here is how to get charging.

Symptoms

• Charger displays 'Payment failed' or 'Authorization error' after tapping your card
• RFID card is not recognized by the charger reader
• We Charge or Elli app shows an error when trying to start a remote session
• Plug & Charge does not activate after plugging in the CCS2 connector
• Contactless payment terminal on the charger rejects your bank card

What to Do

1. 1

   Try a different payment method

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having at least two different payment options covers most situations.

2. 2

   Check the We Charge or Elli app

   Open the We Charge or Elli app on your phone. Make sure your account is active, your payment method is valid, and there are no outstanding charges. Try starting the session remotely through the app.

3. 3

   Scan the charger QR code

   Most public chargers have a QR code on the unit. Scan it with your phone camera. This opens the operator's payment page in your browser, where you can usually pay with a credit card without downloading their specific app.

4. 4

   Check your bank app for blocked transactions

   Open your banking app and look for flagged or declined transactions. If you see a notification about a blocked payment, approve it and try the charger again.

5. 5

   Try Plug & Charge if available

   If the charger supports Plug & Charge and your ID.3 has it activated through We Charge, unplug and replug the CCS2 connector into the right rear charge port. Payment should authorize automatically through the cable.

6. 6

   Move to a different charger

   If nothing works, the charger's payment system may be completely down. Find a nearby alternative using the We Charge app or the ID.3's built-in charger finder on the infotainment screen.

Volkswagen ID.3 Charging Slower Than Expected

You plugged in your ID.3 expecting 130 kW and the infotainment screen shows 40 kW. Or your wallbox at home is stuck at 3 kW instead of 11 kW. The ID.3 Pro has a smaller 59 kWh battery than its siblings, which means the charging curve tapers sooner. But most slow charging has a fixable cause.

Symptoms

• DC fast charging power well below the 130 kW maximum shown on the infotainment display
• AC home charging stuck at 3-4 kW instead of the expected 11 kW on 3-phase
• Charging speed drops sharply after 55-60% during DC fast charging
• Infotainment display shows a long estimated time to reach your target percentage
• Different CCS2 chargers consistently deliver less power than expected

What to Do

1. 1

   Check if preconditioning was active

   On the infotainment screen, look for battery temperature indicators when charging. If the battery was cold, enable preconditioning in the We Charge or Elli app before your next fast charging stop. You can also set a departure time, which warms the battery before you leave.

2. 2

   Check your current state of charge

   If you are above 60%, the reduced speed is expected on the 59 kWh pack. For the fastest DC charging, arrive at the charger between 10-20%. The ID.3 Pro peaks early and tapers sooner than larger-battery VW models.

3. 3

   Verify the charger is not sharing power

   Check if another car is plugged into the same charging station. Some stations split available power between users. If possible, move to a charger unit where no other car is connected.

4. 4

   Check the AC charge current setting

   On the infotainment screen, navigate to the charging settings. Look for the AC charge current or amperage limit. Make sure it is set to the maximum. This only affects AC charging at home or destination chargers.

5. 5

   Try a different charger

   If speeds remain low, the charger may be delivering less than its rated power. Try a different station. Use the We Charge app or the ID.3's built-in charger finder to locate alternatives nearby.

6. 6

   Check for a software update

   Go to the settings menu on the infotainment screen and check for available ID. Software updates. VW has improved charging curves through software updates on MEB platform vehicles. Install any pending updates.

Charger stuck in "preparing" state

You authenticated successfully, the charger says "preparing," but it never starts delivering power. This is one of the most reported issues on Recharge stations, especially at older units.

Symptoms

• Charger screen shows "Preparing" or "Initializing" for more than two minutes
• Your car's charging indicator does not activate
• The Recharge app shows the session as active but 0 kW delivered
• The charger fan spins up but no power flows

How to Fix It

1. 1

   Wait up to three minutes

   Some Recharge units, particularly the 300kW stations, take longer to complete the power handshake with your car. Give it a full three minutes before taking action.

2. 2

   Unplug and reconnect

   Remove the CCS2 connector, wait 15 seconds, then plug it back in firmly. This resets the communication between your car and the charger.

3. 3

   Stop the session in the Recharge app and start a new one

   Open the Recharge app, tap Stop on the active session, wait for it to fully end, then start a new session on the same charger. This clears any stuck state on the backend.

4. 4

   Try the other connector on the same unit

   Many Recharge stations have two CCS2 connectors. If one is stuck, the other connector on the same unit often works fine.

5. 5

   Use a different authentication method

   If you started with the app, try your RFID card instead, or vice versa. Sometimes the issue is with the authentication path, not the charger hardware.

Old Fortum branding causes app scan failure

Recharge was originally part of Fortum's charging operations before being spun off as a separate company. Some older stations still display Fortum logos and QR codes. Scanning an old Fortum QR code with the Recharge app may not work, or it may redirect to a dead Fortum page.

Symptoms

• QR code on the charger opens a Fortum website or shows an error
• Recharge app says "Charger not found" after scanning
• Station ID on the physical unit does not match what the Recharge app expects
• The charger has Fortum branding but is listed as Recharge in third-party apps

How to Fix It

1. 1

   Ignore the QR code and search by station name in the Recharge app

   Open the Recharge app, use the map or search to find the station by location. The charger will appear under its Recharge name even if the physical unit still says Fortum.

2. 2

   Enter the charger ID manually

   Look for a numeric ID on the charger, often printed on a sticker near the connector. In the Recharge app, tap "Enter ID" and type it in directly.

3. 3

   Use RFID or contactless payment instead of the app

   Tap your Recharge RFID card or a contactless bank card on the reader. This bypasses the app entirely and works regardless of the branding on the charger.

4. 4

   Check if contactless is available on this unit

   Not all Recharge stations support contactless bank card payment. Look for a card reader terminal on the charger. If there is no terminal, you will need the app or an RFID card.

RFID card from old Fortum account not recognized

If you had a Fortum Charge & Drive account and RFID card, it may not work automatically on the Recharge network. Some cards were migrated, others were not.

Symptoms

• Tapping your old Fortum RFID card shows "Card not recognized" on the charger
• The charger beeps but does not start a session
• Your Fortum card works on some stations but not others

How to Fix It

1. 1

   Log in to the Recharge app and check your RFID cards

   Open the Recharge app, go to your account settings, and look under RFID cards. If your old Fortum card is not listed, it was not migrated automatically.

2. 2

   Re-register your RFID card

   In the Recharge app, tap "Add RFID card" and follow the steps. You will need the card number printed on the back of your RFID card.

3. 3

   Use the app to start the session while you wait for RFID activation

   RFID card registration can take up to 24 hours to propagate across all stations. Use the app to authenticate in the meantime.

4. 4

   Order a new Recharge RFID card if re-registration fails

   Some older Fortum cards use a chip format that is not compatible. You can order a new Recharge RFID card through the app or website.

Contactless payment not accepted

You are trying to tap your bank card or phone to pay, but the charger does not respond or shows an error. Contactless payment availability varies across Recharge stations.

Symptoms

• No card reader terminal visible on the charger
• Card reader shows "Payment failed" or does not respond to taps
• Apple Pay or Google Pay not recognized
• The charger prompts for an RFID card but you only have a bank card

How to Fix It

1. 1

   Check if this station supports contactless payment

   Look for a separate payment terminal with a contactless symbol. Not all Recharge stations have been upgraded. The Recharge app shows payment options for each station on the station detail page.

2. 2

   Try removing and re-holding your card

   Hold your card flat against the reader for at least three seconds. Some terminals need a longer hold than you might expect. Remove the card fully, then try again.

3. 3

   Fall back to the Recharge app

   If contactless is not working, open the Recharge app and start the session from there. You need a payment method saved in the app.

4. 4

   Try a different card

   Some Visa Electron and certain prepaid cards are not accepted by the payment terminals. A standard Visa or Mastercard debit or credit card usually works.

Charging speed much lower than expected

The station is rated for 300kW, but your car is only pulling 50kW or less. While your car's battery management limits the maximum speed, Recharge stations can also throttle power.

Symptoms

• Charger display shows far less power than the station's rated capacity
• Charging speed drops suddenly mid-session
• Other cars at the same station are also charging slowly
• The Recharge app shows the session but at low power

How to Fix It

1. 1

   Check how many other cars are charging at the same station

   Recharge stations with multiple connectors often share a power cabinet. If two or three cars are charging simultaneously, the available power per car drops. This is normal and not a fault.

2. 2

   Check your battery level

   DC fast charging slows significantly above 80% on most EVs. If your battery is above 70-80%, the slower speed is your car protecting the battery, not a problem with the Recharge station.

3. 3

   Check the temperature

   In cold weather, your car may limit charging speed until the battery warms up. This can take 10-15 minutes of charging before speeds increase. Some cars precondition the battery if you set the charger as a destination in navigation.

4. 4

   Try a different connector at the station

   Individual connectors can have faults that limit power output. If another connector is free, unplug and try it.

5. 5

   Report the issue in the Recharge app

   If the speed is unusually low and none of the above apply, report it through the Recharge app. Tap the active session and look for a "Report issue" option. This helps Recharge identify hardware problems.