Tesla Model S Charging at GreenWay

Tesla Model S Charger Will Not Start a Session

You plugged in your Model S and nothing is happening. No green light on the charge port, no animation on the 17-inch touchscreen, just silence. Whether you are at a Supercharger, a third-party CCS2 station, or a home wallbox, there are a handful of common reasons the session will not begin.

Symptoms

• Charge port LED stays white or flashes red after plugging in the connector
• 17-inch touchscreen shows no charging animation or displays an error message
• Supercharger stall makes a click but does not begin delivering power
• CCS2 connector at a third-party station locks in but charging never starts
• Tesla app shows 'Not Charging' even though the cable is connected

What to Do

1. 1

   Check the charge port LED color

   Walk to the left rear of the car and look at the charge port light. White means ready but not connected. Blue means communicating. Green means charging. Red or amber means there is a fault. If it is white with the cable plugged in, remove and reseat the connector firmly.

2. 2

   Unplug and replug the connector

   Remove the connector completely, wait five seconds, then reinsert it until you hear the latch click. On CCS2 connectors, make sure both the top (AC pins) and bottom (DC pins) sections are seated properly.

3. 3

   Check for scheduled charging on the touchscreen

   On the 17-inch touchscreen, go to Controls, then Charging. If scheduled charging is active, you will see the planned start time. Tap to disable it or select 'Charge Now' to override the schedule.

4. 4

   Authorize the session at non-Tesla chargers

   At third-party CCS2 stations, check whether the charger requires you to start the session through an app, RFID card, or contactless payment. Plug & Charge works at supported stations, but many still require manual authorization.

5. 5

   Try a different stall or charger

   If you are at a Supercharger, move to a different stall. If you are at a third-party station, try the other connector. A faulted charger looks identical to a working one from the outside.

6. 6

   Restart the touchscreen

   Hold both scroll wheels on the steering wheel for about 10 seconds until the 17-inch touchscreen goes black and reboots. This resets the charging controller and fixes some communication glitches. The car stays on during the reboot.

Tesla Model S Payment Failed at Charging Station

You are plugged in and the charger is waiting for payment, or the Supercharger session will not start because of a billing issue. Payment problems are one of the most common reasons drivers get stuck at chargers, and the Model S has multiple ways to pay depending on where you are charging.

Symptoms

• Supercharger session will not start and the Tesla app shows a payment error
• Third-party CCS2 charger displays 'Authorization failed' after tapping your card
• RFID card is not recognized by the charger's reader
• Plug & Charge does not activate at a supported station
• Contactless bank card is rejected by the charger's payment terminal

What to Do

1. 1

   Check your Tesla account payment method

   Open the Tesla app on your phone. Go to Account, then Payment. Verify your credit card is current and has not expired. If the card was replaced, update the details. Supercharger sessions will not start without a valid payment method on file.

2. 2

   Try a different payment method at the charger

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having at least two payment methods gives you a backup when one does not work.

3. 3

   Scan the charger QR code for browser payment

   Most public chargers have a QR code on the unit. Scanning it with your phone opens the operator's payment page in your browser. You can usually pay with a credit card directly without downloading their app.

4. 4

   Check your banking app for blocked transactions

   Open your banking app and look for flagged or declined transactions. Some banks require you to approve the charge manually. Approve it and retry the payment at the charger.

5. 5

   Try Plug & Charge by replugging

   If the charger supports Plug & Charge, unplug the CCS2 connector from your Model S, wait a few seconds, and replug. Payment should authorize automatically through the cable. This only works if your Tesla account has Plug & Charge enabled and the charger supports ISO 15118.

6. 6

   Move to a Supercharger or a different station

   If you cannot resolve the payment issue, find a Tesla Supercharger using the nav on the 17-inch touchscreen. Supercharger billing is handled entirely through your Tesla account, bypassing third-party payment systems.

Tesla Model S Charging Slower Than Expected at Charger

You pulled into a Supercharger expecting 250 kW and the 17-inch touchscreen shows 80 kW. Or your home wallbox is crawling at 3 kW instead of 11 kW. The Model S has one of the fastest charging curves on the road, but reaching peak speed depends on battery temperature, state of charge, and a few settings you can check in under a minute.

Symptoms

• DC fast charging power well below 250 kW on the touchscreen despite a rated charger
• AC home charging stuck at 3-4 kW instead of the expected 11 kW on 3-phase
• Charging speed drops sharply after 40-50% on the touchscreen during DC fast charging
• Supercharger shows significantly lower kW than neighboring stalls
• Non-Tesla CCS2 charger delivers far less power than its rated maximum

What to Do

1. 1

   Check if the battery was preconditioned

   On the 17-inch touchscreen, tap the charging icon. If you see a snowflake icon or a message about conditioning, the battery was not warm enough when you arrived. Next time, navigate to the charger using Tesla nav at least 20-30 minutes before arrival so preconditioning kicks in automatically.

2. 2

   Check your current state of charge

   If you are above 50%, the slower speed is expected on the 95 kWh NCA pack. Peak power happens roughly between 5-30%. For the fastest charging stops on a road trip, arrive between 10-20%.

3. 3

   Move to an unpaired Supercharger stall

   Look at the stall numbers. If they are labeled in A/B pairs (3A/3B, 4A/4B), pick a stall where the paired stall is empty. At V3 or V4 Superchargers with the Magic Dock or the new V4 cable, this is not a concern.

4. 4

   Check the AC charge current limit on the touchscreen

   Go to Controls, then Charging on the touchscreen. Look for the charge current setting. Make sure it is set to the maximum amperage. This only affects AC charging at home or destination chargers, not Supercharging.

5. 5

   Try a different charger or stall

   If speeds remain low, the charger hardware may be degraded. Try another stall at the same location. On non-Tesla CCS2 stations, check the charger display for error codes or reduced power notices.

6. 6

   Check for a Tesla software update

   Go to Controls, then Software on the touchscreen. If an update is pending, install it. Tesla has adjusted charging curves through over-the-air updates in the past, sometimes improving peak speeds.

App-only payment with no backup option

GreenWay stations require the GreenWay app to start a session. There are no contactless card readers or RFID pads. If the app fails or your phone dies, you cannot charge.

Symptoms

• No card reader or RFID pad visible on the charger
• Charger screen shows a QR code or 'Use app to start' message
• You arrived without the app installed and cannot begin a session
• Your phone battery is low and you are worried it will die during setup

How to Fix It

1. 1

   Download the GreenWay app before your trip

   This is non-negotiable for GreenWay stations. Install the app, create an account, and add a payment method while you have good internet and battery. Do this before you leave, not at the charger.

2. 2

   Charge your phone before arriving at the station

   Since you need your phone to start and monitor the session, make sure it has enough battery. Use your car's USB port or a power bank on the way.

3. 3

   Try a roaming app as a backup

   Some GreenWay stations are accessible through roaming providers like Plugsurfing, Shell Recharge, or Chargemap. Check your roaming app's map to see if the specific station is covered before counting on it.

4. 4

   Scan the QR code on the charger

   If you do not have the app, scan the QR code with your phone camera. It may direct you to the app store or, in some cases, to a web-based session start page.

App requires location services for charger activation

The GreenWay app needs location services turned on to activate a charger. Without it, the app cannot verify that you are at the station and will not let you start a session.

Symptoms

• App shows 'Enable location services' and will not proceed
• You can see the charger on the map but cannot start a session
• The 'Start charging' button is grayed out or unresponsive
• App shows your location incorrectly, placing you far from the station

How to Fix It

1. 1

   Enable location services for the GreenWay app

   Go to your phone settings, find the GreenWay app, and set location access to 'While Using' or 'Always.' On iPhone: Settings, Privacy, Location Services, GreenWay. On Android: Settings, Apps, GreenWay, Permissions, Location.

2. 2

   Make sure GPS is turned on, not just Wi-Fi location

   In some areas, Wi-Fi-based location is inaccurate. Turn on full GPS (high accuracy mode on Android) for a precise position fix at the station.

3. 3

   Step outside your vehicle briefly

   If GPS signal is weak (underground parking, dense urban area), step a few meters away from your car with your phone. This can help the GPS lock onto your position.

4. 4

   Try selecting the charger manually

   If the app cannot determine your location, try tapping on the station on the map manually or entering the charger's ID number (printed on the charger unit). Some app versions allow manual selection as a fallback.

Coverage gaps between cities

GreenWay's network is concentrated in and around cities. Between major cities, especially on secondary roads, there can be long stretches with no GreenWay stations.

Symptoms

• No GreenWay stations shown on the app map for 100+ km stretches
• The nearest GreenWay station requires a detour off your route
• You planned a trip assuming GreenWay coverage and ran into a gap
• Available stations between cities are AC-only (slow), not DC fast charging

How to Fix It

1. 1

   Plan your route and charging stops before leaving

   Use the GreenWay app or a route planner like ABRP (A Better Route Planner) to map out charging stops. Identify gaps in advance so you are not caught by surprise.

2. 2

   Have alternative charging networks ready

   Install apps for other networks that operate in the region. In Slovakia and Poland, look for Ionity, Shell Recharge, or Greencharge. In Czech Republic, check CEZ or PRE. Having multiple apps ensures you always have a fallback.

3. 3

   Charge to a higher level before entering a gap

   If you know there is a 150+ km stretch without fast chargers, charge to 90 or even 95% at the last available station. The slower charging speed above 80% is worth it if the alternative is running out of range.

4. 4

   Check for AC chargers as emergency backup

   Hotels, shopping centers, and some gas stations in Central Europe have AC chargers (Type 2, 11 to 22 kW). These are slow but can add enough range to reach the next fast charger. Many are accessible through Chargemap or Plugsurfing.

Charger screen errors in local language only

When a GreenWay charger displays an error, the message is often in Slovak, Polish, or Czech with no English translation. Understanding what went wrong is difficult.

Symptoms

• Error message appears in Slovak, Polish, or Czech
• You cannot tell if the error is temporary or requires support
• The charger stopped and you do not know why
• The error code is visible but the description is in a language you do not read

How to Fix It

1. 1

   Note the error code, not just the text

   Most error messages include a numeric or alphanumeric code (like E-101 or ERR_04). Write down or photograph the code. This is useful for support and often means the same thing regardless of language.

2. 2

   Use your phone camera to translate the screen

   Open Google Translate or Apple Translate, switch to camera mode, and point it at the charger screen. This gives a real-time translation of the error message.

3. 3

   Try unplugging and restarting the session

   Many error messages clear on a retry. Unplug, wait 15 seconds, plug back in, and start a new session through the app. Common errors like 'Communication timeout' resolve themselves.

4. 4

   Contact GreenWay support with the error code

   If the error persists, contact support through the GreenWay app. Provide the error code and the station ID (printed on the charger). GreenWay support can tell you whether the issue is temporary or requires a technician.

Power limited at older installations

Some older GreenWay stations deliver less than 150 kW. They may be rated at 50 kW or have degraded power output due to aging hardware.

Symptoms

• Charging speed maxes out at 50 kW on a station advertised as 150 kW
• The charger label says 150 kW but your vehicle never receives more than 50 kW
• Speed is significantly lower than what you get at newer GreenWay stations
• The app shows the station as 150 kW but the charger hardware looks older

How to Fix It

1. 1

   Check the charger label for the actual rated power

   The charger unit itself has a label showing its maximum output. Older GreenWay units may be rated at 50 kW despite the station listing showing 150 kW (which may refer to a newer unit at the same location).

2. 2

   Check if the station has multiple charger types

   Some GreenWay stations have both older 50 kW and newer 150 kW chargers. Make sure you are plugged into the newer, higher-power unit. It is usually the larger cabinet.

3. 3

   Verify your vehicle's battery level and temperature

   Your vehicle limits charging speed when the battery is above 60 to 80% or when the battery is cold. Check your dashboard to confirm the car is requesting more than what the charger delivers.

4. 4

   Use a different station if speed matters

   If you need faster charging and the station is limited, check the GreenWay app for a newer station nearby. Filter by power level to find 150 kW units specifically.