Skoda Enyaq Charging at ABC-lataus

Skoda Enyaq Charger Won't Start Charging

You have plugged in your Enyaq, the connector clicked into the charge port on the right rear fender, but nothing happens. The infotainment screen stays silent or shows an error. This is frustrating, but it is almost always fixable on the spot without calling roadside assistance.

Symptoms

• CCS2 or Type 2 connector plugged in but no charging indicator on the infotainment display
• Charger screen shows 'Waiting for vehicle' or stays on the start screen
• Enyaq charge port LED blinks but charging never begins
• Authentication succeeds on the charger but the session fails to start
• Instrument cluster briefly shows a charging icon, then it disappears

What to Do

1. 1

   Check for a charging schedule or timer

   On the infotainment screen, go to the vehicle settings, then charging. If a timer or schedule is active, switch it to charge immediately or turn off the timer. You can also check the MySkoda app for active schedules.

2. 2

   Unplug and reconnect firmly

   Open the charge port on the right rear fender using the button on the port. Remove the connector, wait 10 seconds, then reinsert it firmly until you hear a clear click. Watch the charge port LED for a steady green light.

3. 3

   Restart the charger session

   On the charger, end the current session if one is active. Then start a new session by tapping your RFID card, using contactless payment, or restarting in the charger operator's app.

4. 4

   Try Plug & Charge or a different payment method

   If your Enyaq has Plug & Charge set up through the MySkoda app, make sure the charger supports it. Otherwise, switch to a different RFID card, contactless payment, or the charger operator's own app.

5. 5

   Reboot the infotainment system

   Press and hold the power button on the infotainment screen for about 10 seconds until the screen goes dark and restarts. Once it is back, try plugging in again. This resets the charging communication on the car's side.

6. 6

   Try a different charger or cable

   If the station has multiple stalls, move to a different one. If you are at an AC charger with your own cable, try a different cable. A faulty charger is more common than a faulty car.

Skoda Enyaq Charging Payment Failed at Station

You are at the charger, your Enyaq is plugged in, but the payment will not go through. The charger shows an error or just sits there waiting. Payment failures at public chargers are common and usually have nothing to do with your car. Here is how to get charging.

Symptoms

• Charger displays 'Payment failed' or 'Authorization error' after tapping your card
• RFID card is not recognized by the charger's reader
• MySkoda app or Skoda charging service shows an error when trying to start a remote session
• Plug & Charge does not activate after plugging in the CCS2 connector
• Contactless payment terminal on the charger rejects your bank card

What to Do

1. 1

   Try a different payment method

   If your RFID card failed, try contactless with your bank card or phone. If contactless failed, try the charger operator's app. Having two or three payment options gives you the best chance of getting going.

2. 2

   Check the MySkoda app

   Open the MySkoda app on your phone. Make sure your Skoda charging account is active, your payment method is valid, and Plug & Charge is enabled if you want to use it. Try starting the session remotely through the app.

3. 3

   Scan the charger's QR code

   Most public chargers have a QR code on the unit. Scanning it with your phone's camera opens the operator's payment page. You can usually pay with a credit card through the browser without downloading an app.

4. 4

   Check your bank app for blocked transactions

   Open your banking app and check for any flagged or blocked transactions. Some banks require you to approve the charge manually. If you see a notification, approve it and try the payment again.

5. 5

   Try Plug & Charge if available

   If the charger supports Plug & Charge and your Enyaq has it activated through the MySkoda app, simply unplug and replug the CCS2 connector. The payment should authorize automatically through the cable without any card or app.

6. 6

   Move to a different charger

   If nothing works at this station, the charger's payment system may be down entirely. Find a nearby alternative using the MySkoda app or the Enyaq's built-in charger finder on the infotainment screen.

Skoda Enyaq Charging Slower Than Expected

You plugged in your Enyaq expecting 135 kW and the infotainment screen shows 30 kW. Or your home wallbox is stuck at 3 kW instead of the full 11 kW. Slow charging on the Enyaq is almost never a defect. It is usually the battery temperature, the charger itself, or a setting you can fix right now.

Symptoms

• DC fast charging speed well below the 135 kW maximum shown on the infotainment display
• AC home charging stuck at 3-4 kW instead of the full 11 kW
• Charging speed drops significantly after reaching 50-60% state of charge
• Charging session starts at a reasonable speed but drops quickly within minutes
• Infotainment display shows lower power than the charger's rated output

What to Do

1. 1

   Check the battery temperature

   Look at the charging screen on the infotainment display. If the battery is cold, use the navigation system to route to the fast charger. The Enyaq will precondition the battery automatically on the way. If you are already at the charger, driving for 15-20 minutes and returning can help.

2. 2

   Check your state of charge

   Look at the instrument cluster or infotainment screen. If you are above 80%, the slower speed is expected. For the fastest charging, arrive at the charger between 10-20% and charge to 80%.

3. 3

   Verify the charger is not sharing power

   Look at the charger unit. If there are two cables and someone is using the other one, you may be sharing power. Move to an unoccupied charger if one is available.

4. 4

   Check the AC charge current setting

   On the infotainment screen, go to the vehicle settings, then charging. Make sure the AC charge current is set to maximum. The Enyaq lets you adjust this, and it may have been lowered accidentally.

5. 5

   Check for software updates

   On the infotainment screen, check for available updates, or use the MySkoda app to see if an over-the-air update is ready. Skoda has released updates that improve the Enyaq's DC charging curve on the MEB platform.

6. 6

   Try a different charger

   If the speed is still low, the charger itself may be degraded or faulty. Try a different stall at the same location or a different charging station entirely.

Session fails to start or charger shows an error

You plug in and try to authenticate, but the charger does not begin charging. This can happen due to communication issues between your vehicle and the charger, or a problem with authentication.

Symptoms

• Charger shows an error after you try to start a session
• Contactless card payment does not work at this station (older unit without payment terminal)
• Card reader beeps but the session does not start
• The app says the session is starting but nothing happens at the charger

How to Fix It

1. 1

   Unplug, wait 30 seconds, and try again

   The initial communication handshake between your vehicle and the charger can fail. Unplug the connector, wait at least 30 seconds, and reconnect. The second attempt often works.

2. 2

   Try starting the session through the ABC-lataus app

   If the card reader is not cooperating, open the ABC-lataus app, select the station, and start the session from your phone. This bypasses the physical card reader entirely.

3. 3

   Try contactless card payment at newer stations

   Some newer ABC-lataus high-power stations have a contactless payment terminal. If the app is not cooperating, look for a card reader on the charger unit and tap your bank card. Older stations may not have this option.

4. 4

   Try a different charger unit at the same station

   If the station has multiple charger units, switch to another one. One unit may have a hardware issue while the others work fine.

Finding the EV charger at a busy fuel station

ABC-lataus chargers are located at ABC fuel stations, which also serve diesel and petrol vehicles. The EV charging spots can be easy to miss if you are visiting for the first time.

Symptoms

• You arrived at the ABC station but cannot see the EV charger
• The charger is behind the fuel pump area or in a separate parking section
• Other vehicles (non-EV) are parked in the charging spots
• Signage is not visible from the main road entrance

How to Fix It

1. 1

   Check the ABC-lataus app for the charger's exact location

   The app shows station details including photos or layout hints. Some ABC stations place chargers at the far end of the parking area, away from the fuel pumps.

2. 2

   Look for the CCS2 cable and charging unit

   The charger unit is taller than a fuel pump and usually has a clearly different design. Look for a separate bay with a CCS2 cable, often marked with green signage or an EV symbol on the ground.

3. 3

   Drive past the fuel pumps

   At many ABC stations, the EV charger is positioned after the fuel pump area or in a dedicated corner of the parking lot. Do not stop at the fuel pumps. Continue through and scan for the charging unit.

4. 4

   If an ICE vehicle is blocking the spot, report it

   ABC stations serve all types of vehicles. If a non-EV is parked in the charging bay, contact ABC customer service through the app. Unfortunately, there is not much you can do in the moment besides trying another station.

App setup confusion within the S-Group ecosystem

The ABC-lataus app is part of the S-Group digital ecosystem. If you already use S-mobiili for groceries or fuel, the relationship between the apps can be confusing.

Symptoms

• You are not sure whether to use S-mobiili or the ABC-lataus app
• Your S-Group login works in one app but not the other
• Charging payments do not appear in your S-mobiili transaction history
• You created a new account instead of linking your existing S-Group membership

How to Fix It

1. 1

   Use the ABC-lataus app for starting and managing charging sessions

   While S-mobiili handles your broader S-Group membership, the ABC-lataus app is the dedicated tool for finding stations, starting sessions, and viewing charging history. Install it separately from the App Store or Google Play.

2. 2

   Log in with your existing S-Group credentials

   Use the same username and password you use for S-mobiili or s-kanava.fi. Do not create a new account.

3. 3

   Check payment method settings in the ABC-lataus app

   Even if you have a payment card saved in S-mobiili, the ABC-lataus app may require you to add a payment method separately. Go to settings or payment in the ABC-lataus app and add your card there.

4. 4

   Verify your account is set up for charging

   Check the ABC-lataus app settings to make sure your payment method is saved and charging is enabled.

Connector stuck or difficult to insert in winter cold

Finnish winters mean temperatures well below freezing. The CCS2 connector locking mechanism and the vehicle's charge port can freeze, making it hard to plug in or unplug.

Symptoms

• The CCS2 connector will not click into your vehicle's charge port
• The connector is plugged in but the locking mechanism will not engage
• You cannot release the connector after charging is complete
• The connector handle feels stiff or the release button is frozen

How to Fix It

1. 1

   Check your vehicle's charge port for ice

   Open the charge port door and look for ice buildup around the opening or inside the port. Brush away any loose ice or snow with your hand or a soft brush. Do not use sharp tools, as you can damage the pins.

2. 2

   Warm the connector in your hands for a moment

   If the connector handle feels frozen stiff, hold it in your hands for 30 seconds to warm the mechanism slightly. The locking button and release lever work better when they are not frozen solid.

3. 3

   Push the connector in firmly and straight

   In cold weather, plastic contracts and tolerances get tighter. Line up the connector carefully and push it in with steady, even pressure. Do not force it at an angle.

4. 4

   If the connector is stuck after charging, try unlocking from your car

   Use your vehicle's unlock button or the in-car menu to release the charge port lock. Some vehicles also release the connector when you unlock the doors. If it is still stuck, wait a few minutes. The charging session generates heat that may free the mechanism.

5. 5

   Contact support if the connector will not release

   Do not yank the connector. Forcing it can damage both the cable and your vehicle's charge port. Call ABC-lataus support and they can guide you through a remote release or send help.

Charging session starts but power delivery is low

The charger is rated for 200 kW, but your session is delivering significantly less. Several factors specific to ABC-lataus stations can contribute.

Symptoms

• Dashboard shows 30 to 50 kW at a 200 kW rated charger
• Charging speed drops after a few minutes
• Speed is lower than what you get at other fast chargers
• The charger screen shows a lower maximum than 200 kW

How to Fix It

1. 1

   Check your vehicle's maximum DC charging rate

   A 200 kW charger does not mean your vehicle can accept 200 kW. Many EVs max out at 50 to 150 kW depending on the model, battery temperature, and state of charge. Check your vehicle's specifications.

2. 2

   Consider battery temperature in Finnish conditions

   Cold batteries accept less power. If your vehicle has been parked outside in freezing temperatures, the battery may need to warm up before it can accept higher charging speeds. Some vehicles have a preconditioning feature you can activate before arriving.

3. 3

   Check if another vehicle is sharing the station's power

   Some ABC-lataus locations share power between charger units. If another vehicle is charging at the same station, your available power may be split. This is normal and not a fault.

4. 4

   Arrive with a lower state of charge for faster charging

   Charging is fastest between 10% and 50% state of charge. If you arrive at 60% or higher, the charger will taper the power to protect your battery. This is your vehicle's doing, not the charger's.