Porsche Taycan Charging at Atlante

Porsche Taycan Charger Will Not Start a Session

You are at the charger, the CCS2 connector is in, but nothing happens. The charger screen stays on the start page, or shows an error and resets. Charger startup problems on the Taycan are almost always about the connector fit, the charge port location, or authentication. Here is how to get the session going.

Symptoms

• Charger screen stays on the welcome page after plugging in
• Charger displays an error code and resets to the start screen
• Charge port light on the Taycan does not turn on or blinks red
• CCS2 connector clicks in but the car does not acknowledge it
• Charger says 'Vehicle not detected' or 'Communication error'

What to Do

1. 1

   Reinsert the CCS2 connector firmly

   Remove the connector completely, check for debris or ice in the Taycan's charge port, and reinsert it straight and firm until you hear and feel a click. The charge port light should turn on.

2. 2

   Check the charge port flap

   Make sure the charge port door on the right rear is fully open. If it is stuck, gently push it. In freezing conditions, use warm water (never force it) to free any ice. The flap must be clear of the connector path.

3. 3

   Confirm the car is in Park

   Check the PCM display to make sure the Taycan is in Park. Also check that no charging timer or schedule is blocking immediate charging. Go to Settings, then Charging, and verify that direct charging is enabled.

4. 4

   Authenticate with the charger

   Tap your RFID card, start the session in the charger operator's app, or use Porsche Charging Service through the My Porsche app. Make sure you select the correct stall number if using an app. Wait for the charger to confirm authorization before expecting the session to begin.

5. 5

   Try a different stall or station

   If the charger still will not start after reinserting the connector and authenticating, the charger may be faulty. Try a different stall at the same location. If all stalls fail, move to the nearest alternative station.

6. 6

   Restart the Taycan's infotainment system

   In rare cases, restarting the PCM can resolve communication issues. Hold down the center display button for about 10 seconds until the screen goes dark, then release. Wait for it to restart and try plugging in again.

Porsche Taycan Charging Payment Failed at Station

You are at the charger, your Taycan is plugged in, but the payment will not go through. The charger says 'Authorization failed' or the Porsche Charging Service app is not connecting. Payment issues are one of the top reasons a charging session never starts. Most of the time, the fix takes less than two minutes.

Symptoms

• Charger screen shows 'Authorization failed' or 'Payment declined'
• Porsche Charging Service does not start the session automatically
• RFID card tap produces an error or no response from the charger
• Contactless bank card is declined at the charger's payment terminal
• Charger accepts payment but the session ends immediately with zero kWh

What to Do

1. 1

   Check Porsche Charging Service status

   Open the My Porsche app and check your Charging Service contract. Make sure it is active and your payment method on file is valid. If it has expired, renew it or switch to a different payment method at the charger.

2. 2

   Try the charger operator's app

   Look for the network name on the charger (Ionity, Shell Recharge, Allego, EnBW, etc.). Open their app, add a payment method if you have not already, and start the session. Make sure the stall number in the app matches the number on the charger you are using.

3. 3

   Try a different payment method

   If your primary method fails, switch to a backup. Try a different RFID card, a different bank card for contactless, or a different charging app. Having at least two options covers most situations.

4. 4

   Check your card balance

   Open your banking app and verify you have enough available balance for the pre-authorization hold. Previous charging sessions may have pending holds that reduce your available balance temporarily.

5. 5

   Reset the charger and try again

   Press the stop or reset button on the charger. Wait for it to return to the welcome screen. Unplug the connector from your Taycan, wait 30 seconds, plug back in, and authenticate again.

6. 6

   Move to a different stall or station

   If nothing works, try a different stall at the same station. Payment terminals can fail independently. If the entire station is not processing payments, use your Taycan's PCM navigation or Google Maps to find the nearest alternative.

Porsche Taycan Charging Slower Than Expected

You plugged in your Porsche Taycan expecting 270 kW and the Porsche Communication Management screen shows 80 kW. Or your wallbox is stuck at 3 kW instead of 11 kW. The Taycan has one of the fastest charging architectures on the market, but real-world speeds depend on battery temperature, charger capability, and a few settings you can check yourself.

Symptoms

• DC fast charging speed well below the 270 kW maximum
• AC home charging stuck at 3-4 kW instead of 11 kW or 22 kW
• Charging speed drops sharply after reaching 50-60%
• PCM shows lower power than the charger's rated output
• Charging session starts fast but slows down within minutes

What to Do

1. 1

   Use Porsche navigation for preconditioning

   Enter your charging stop as a destination in the Porsche Communication Management system. The Taycan will automatically precondition the battery to the ideal temperature during the drive. This is the single most effective way to reach peak charging speeds.

2. 2

   Check if the charger supports 800V

   Look at the charger's specifications, usually printed on the unit or shown in the operator's app. Chargers rated at 350 kW (like Ionity HPC) typically support 800V. If the charger is 50 kW or 150 kW, expect lower speeds regardless of your Taycan's capability.

3. 3

   Check your state of charge

   If you are above 80%, the slower speed is by design. For the fastest charging, arrive between 5-20% and charge to 80%. The Taycan's charging curve is steepest in this range.

4. 4

   Verify your AC charging setup

   For home charging, check whether your wallbox is wired for 3-phase power. In the Taycan's charging settings on PCM, confirm the AC charge current is set to maximum. If you have the 22 kW AC option, your wallbox must also support 22 kW.

5. 5

   Try a different charger or stall

   If speeds remain low at a DC charger, move to an unoccupied stall or a different station. Some chargers degrade over time and deliver less than their rated power. The My Porsche app or Porsche Charging Service can help find 800V-capable chargers nearby.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.