Peugeot e-2008 Charging at Atlante

Peugeot e-2008 Charger Won't Start? Try These Steps

You have connected your Peugeot e-2008 to the charger, but nothing happens. No power, no progress, maybe an error on the charger screen. This is frustrating but usually fixable. Here are the most common causes and what to do about each one.

Symptoms

• CCS2 connector plugged in but no session begins
• Charger screen displays an error or failed connection message
• The e-2008's charge port indicator does not light up or blinks red
• Charger starts initializing but disconnects within seconds
• Type 2 connector locks in at an AC charger but no power flows

What to Do

1. 1

   Complete the payment or authentication step

   Tap your RFID card, start a session in the charging network app, or use contactless payment. Follow the charger's on-screen instructions for the correct order of authentication and plug-in.

2. 2

   Unplug and firmly reseat the connector

   Pull out the CCS2 or Type 2 connector completely. Push it back in straight and firmly until it clicks into the e-2008's charge port. Support the cable weight with your other hand.

3. 3

   Turn off scheduled charging in the i-Cockpit

   Open the charging settings on the e-2008's central touchscreen. If scheduled charging is active, disable it. This lets the car accept power immediately instead of waiting for a time window.

4. 4

   Clean the charge port

   Inspect the charge port on the left rear for dirt, salt, or ice. Wipe the contacts gently with a dry cloth. In winter, clear any ice from the port opening and door hinge.

5. 5

   Lock and unlock the car to reset

   Use the key fob or MyPeugeot app to lock the e-2008, wait 10 seconds, then unlock it. This resets the charge port controller. Try connecting again.

6. 6

   Move to a different charger

   If the issue persists, try another stall at the same station or find a nearby alternative. Some charger faults are specific to individual units.

Peugeot e-2008: Charger Payment Failed? Solutions

Your Peugeot e-2008 is plugged in and ready, but the payment is failing. RFID rejected, app error, bank card declined. The good news is this has nothing to do with your car. The bad news is you need to sort it out before you can charge. Here is how.

Symptoms

• RFID card rejected with an error message on the charger
• Charging network app fails to start the session or shows a payment error
• Contactless bank card declined at the charger terminal
• Pre-authorization hold on your bank account but no charging session
• Charger starts briefly then stops with a billing error

What to Do

1. 1

   Check what payment methods the charger accepts

   Look at the charger screen and body for logos of accepted RFID networks, app payment, or contactless card terminals. This tells you which methods are available.

2. 2

   Switch to a different payment method

   If RFID fails, try the charging network app. If the app fails, try a contactless bank card. Having at least two backup options is essential.

3. 3

   Check your bank card balance and limits

   Open your banking app and verify your card has enough available balance for a pre-authorization hold. Some chargers hold up to 80 EUR temporarily.

4. 4

   Update or restart the charging network app

   Check for app updates, close and reopen the app, and check for any stuck open sessions. Log out and back in if the error persists.

5. 5

   Use the built-in card reader if available

   More European chargers now have contactless card readers built in. Look for a card terminal on the charger unit and tap your bank card directly.

6. 6

   Call the charger support number

   The phone number is printed on every public charger. The operator can often start a session remotely or confirm if the charger has a known issue.

Peugeot e-2008 Charging Slow? Here Is How to Fix It

Your Peugeot e-2008 supports up to 107 kW DC fast charging with its 50.8 kWh NMC811 battery. But at the charger, the numbers may tell a different story. The e-2008 sits on the Stellantis e-CMP2 platform and shares some charging characteristics with its siblings. Here is what limits your speed and how to get better results.

Symptoms

• DC charging power stays well below 107 kW on a high-power charger
• Charging speed drops sharply before reaching 50% state of charge
• Home AC charging stuck at 3.6 kW instead of 11 kW
• The i-Cockpit display shows a much longer estimated time than expected
• Winter charging sessions are significantly slower than summer sessions

What to Do

1. 1

   Drive at highway speed for 15-20 minutes before fast charging

   The e-2008 cannot precondition its battery, so driving actively before your stop is the best alternative. Highway driving generates enough heat to bring the battery closer to optimal charging temperature, especially in winter.

2. 2

   Arrive at the charger between 10% and 20%

   The e-2008 charges fastest at low state of charge. Plan your stop so you arrive around 10-15%. The difference between arriving at 10% and 50% can mean 30-40 kW less charging power.

3. 3

   Choose an unshared charger stall

   Check the station layout. If two CCS2 cables come from one unit, pick the stall where the other connector is not in use. This gives you access to the full power output.

4. 4

   Verify your home AC installation

   Check the charging power on the i-Cockpit screen during a home AC session. If it reads about 3.6 kW, you are on single-phase. A three-phase upgrade unlocks 11 kW and significantly reduces charging time.

5. 5

   Monitor the charging display

   During DC charging, the i-Cockpit shows current power and battery temperature. If power starts low, the battery is likely still cold. It should ramp up over the first 5-10 minutes as the battery warms.

6. 6

   Unplug at 80% on road trips

   Charging from 80% to 100% on DC takes disproportionately long due to tapering. On road trips, charge to 80%, drive to the next stop, and charge again. This is almost always faster overall.

New station with teething problems

Atlante is expanding rapidly, and many stations are brand new. Newly installed chargers sometimes have firmware bugs, incomplete network configuration, or hardware that has not been fully tested under real-world conditions.

Symptoms

• Charger turns on but fails to communicate with your vehicle
• Session starts but drops after a few seconds
• Charger screen shows an error code you have never seen before
• Station appears on the map but the chargers are not yet operational

How to Fix It

1. 1

   Try a different charger at the same station

   New stations often have multiple units and the issue may be limited to one charger. Try another unit before giving up on the location.

2. 2

   Unplug, wait 30 seconds, and retry

   New charger firmware sometimes fails on the first handshake but succeeds on the second attempt. A short wait lets the charger reset its session state.

3. 3

   Start the session through the Atlante app

   If the charger's screen or contactless reader is not working properly, the app provides a separate communication path to the charger's backend. This can bypass local hardware issues.

4. 4

   Check the Atlante app for station status notes

   Atlante sometimes posts notices about newly activated stations that are still in testing. The station detail page in the app may show a note about limited functionality.

5. 5

   Report the issue and move to the next station

   Use the Atlante app to report the problem. New station issues are usually fixed quickly once reported. Check the app for the nearest alternative Atlante or competitor station.

App crashes on older phones

The Atlante app can be unstable on older phones or phones running outdated operating systems. The app may crash during login, while loading the map, or in the middle of starting a session.

Symptoms

• App closes unexpectedly when you open the station map
• App freezes during the payment screen
• Login screen loads but the app crashes after entering credentials
• App works briefly but crashes when you try to start a session

How to Fix It

1. 1

   Update the Atlante app to the latest version

   Atlante pushes frequent updates that fix stability issues. Open the App Store or Google Play and check for updates before your trip.

2. 2

   Clear the app cache

   On Android, go to Settings, Apps, Atlante, and clear the cache. On iPhone, delete and reinstall the app. Corrupted cache data is a common cause of crashes.

3. 3

   Check your phone's operating system version

   The Atlante app may require iOS 15+ or Android 10+. If your phone is on an older version, update if possible. If your phone cannot update, you may need a roaming app as a backup.

4. 4

   Use contactless payment as a fallback

   If the app keeps crashing and the station supports contactless, tap your credit or debit card on the charger's payment terminal. Not all Atlante stations have this yet, but it completely bypasses the app.

5. 5

   Try a roaming app

   Apps like Chargemap, Shell Recharge, or Electropass can start sessions at Atlante stations without using the Atlante app. Check roaming coverage before relying on this.

Contactless payment terminal not activated

Atlante is rolling out contactless card payment across its network, but not every charger has an active terminal yet. Some units have the hardware installed but the payment function is not turned on.

Symptoms

• Card reader is visible on the charger but does not respond to a tap
• Screen says 'Use app to start' with no contactless option shown
• Contactless symbol is printed on the charger but the reader light is off
• You see a payment terminal but tapping produces no response

How to Fix It

1. 1

   Download and use the Atlante app

   At stations where contactless is not yet active, the Atlante app is the primary payment method. Download it before your trip and add a payment card in advance.

2. 2

   Check the charger screen for payment instructions

   Some Atlante chargers display which payment methods are currently available. If contactless is not listed, the terminal is not active at that unit.

3. 3

   Try a different charger at the same station

   Contactless activation sometimes rolls out unit by unit. Another charger at the same station may have an active terminal.

4. 4

   Use a roaming RFID card or app

   If you have an RFID card from a roaming provider, try tapping it. Some Atlante stations accept roaming RFID even when the contactless card terminal is not active.

Charger screen hard to read in direct sunlight

Some Atlante charger screens have low brightness levels that make them nearly impossible to read in bright sunlight. This is especially common at stations in Southern Europe during summer.

Symptoms

• Screen content is barely visible outdoors during the day
• You cannot read the price, status, or error messages on the screen
• Screen appears to be off but the charger is actually on
• You have to cup your hands around the screen to read it

How to Fix It

1. 1

   Use your body or hand to shade the screen

   Stand to block direct sunlight from hitting the screen. Even partial shade can make the display readable.

2. 2

   Take a photo of the screen with your phone

   Your phone camera can sometimes capture what your eyes cannot. Take a photo and zoom in to read the text.

3. 3

   Use the Atlante app to monitor your session

   All session information (charging speed, energy delivered, cost, estimated time) is available in the app. You do not need the charger screen to track your session.

4. 4

   Start the session entirely through the app

   If you cannot read the screen at all, use the Atlante app to select the charger, start the session, and stop it when done. This avoids needing to interact with the screen.

Cable connector requires specific angle to lock

Some Atlante charger cables need to be inserted at a particular angle or with extra force for the CCS2 connector to seat properly. If it is not fully locked, the session will not start.

Symptoms

• Connector feels like it is in but the charger does not recognize it
• Charger screen says 'Connect cable' even though the cable is plugged in
• You hear a partial click but the connector is not locked
• Connector slides back out after you let go

How to Fix It

1. 1

   Push the connector straight in, then slightly upward

   Some Atlante CCS2 connectors need a slight upward tilt after the initial push to engage the locking mechanism. You should feel and hear a solid click.

2. 2

   Check for debris in the vehicle's charging port

   Dust, ice, or a small pebble in the port can prevent the connector from seating fully. Inspect the port and brush out anything you find.

3. 3

   Make sure the vehicle is unlocked and ready to charge

   Some vehicles lock the charging port flap or disable the inlet when the car is locked or in drive mode. Ensure the car is in park and unlocked.

4. 4

   Try a different cable if the charger has two

   If the charger has two CCS2 cables, try the other one. One cable may have a slightly worn connector that does not seat as easily.